|
SIST EN ISO/ASTM 52909:2023
01-marec-2023
Aditivna proizvodnja kovin - Lastnosti končnih delov - Orientacija in lokacija v
odvisnosti od mehanskih lastnosti za spajanje kovinskega prahu v postelji
(ISO/ASTM 52909:2022)
Additive manufacturing of metals - Finished part properties - Orientation and location
dependence of mechanical properties for metal powder bed fusion (ISO/ASTM
52909:2022)
Additive Fertigung von Metallen - Eigenschaften von Fertigteilen - Orientierung und Lage
in Abhängigkeit der mechanischen Eigenschaften für pulverbettbasiertes Schmelzen von
Metallen (ISO/ASTM 52909:2022)
Fabrication additive de métaux - Propriétés des pièces finies - Dépendance de
l'orientation et de l'emplacement sur les propriétés mécaniques pour la fusion sur lit de
poudre métallique (ISO/ASTM 52909:2022)
Ta slovenski standard je istoveten z: EN ISO/ASTM 52909:2022
ICS:
25.030 3D-tiskanje Additive manufacturing
SIST EN ISO/ASTM 52909:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO/ASTM 52909:2023
---------------------- Page: 2 ----------------------
SIST EN ISO/ASTM 52909:2023
EN ISO/ASTM 52909
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 25.030
English Version
Additive manufacturing - Finished part properties -
Orientation and location dependence of mechanical
properties for metal powder bed fusion (ISO/ASTM
52909:2022)
Fabrication additive de métaux - Propriétés des pièces Additive Fertigung von Metallen - Eigenschaften von
finies - Dépendance de l'orientation et de Fertigteilen - Orientierung und Lage in Abhängigkeit
l'emplacement sur les propriétés mécaniques pour la der mechanischen Eigenschaften für
fusion sur lit de poudre métallique (ISO/ASTM pulverbettbasiertes Schmelzen (ISO/ASTM
52909:2022) 52909:2022)
This European Standard was approved by CEN on 25 April 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO/ASTM 52909:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO/ASTM 52909:2023
EN ISO/ASTM 52909:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO/ASTM 52909:2023
EN ISO/ASTM 52909:2022 (E)
European foreword
This document (EN ISO/ASTM 52909:2022) has been prepared by Technical Committee ISO/TC 261
"Additive manufacturing" in collaboration with Technical Committee CEN/TC 438 “Additive
Manufacturing” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark,
...