|
SIST EN ISO 8092-1:2000
01-december-2000
Road vehicles - Connections for on-board electrical wiring harnesses - Part 1:
Tabs for single-pole connections - Dimensions and specific requirements (ISO
8092-1:1996)
Road vehicles - Connections for on-board electrical wiring harnesses - Part 1: Tabs for
single-pole connections - Dimensions and specific requirements (ISO 8092-1:1996)
Straßenfahrzeuge - Steckverbindungen für das elektrische Fahrzeug-Bordnetz - Teil 1:
Flachstecker für einpolige Steckverbindungen - Maße und besondere Anforderungen
(ISO 8092-1:1996)
Véhicules routiers - Connections pour faisceaux de câblage électrique embarqués -
Partie 1: Languettes pour raccordements unipolaires - Dimensions et exigences
particulieres (ISO 8092-1:1996)
Ta slovenski standard je istoveten z: EN ISO 8092-1:1998
ICS:
43.040.10 (OHNWULþQDLQHOHNWURQVND Electrical and electronic
RSUHPD equipment
SIST EN ISO 8092-1:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8092-1:2000
---------------------- Page: 2 ----------------------
SIST EN ISO 8092-1:2000
---------------------- Page: 3 ----------------------
SIST EN ISO 8092-1:2000
---------------------- Page: 4 ----------------------
SIST EN ISO 8092-1:2000
---------------------- Page: 5 ----------------------
SIST EN ISO 8092-1:2000
---------------------- Page: 6 ----------------------
SIST EN ISO 8092-1:2000
I NTERNAT IO NAL IS0
STANDARD
8092-1
Second edition
1996-02-01
Road vehicles - Connections for on-board
electrical wiring harnesses -
Part 1:
Tabs for single-pole connections -
Dimensions and specific requirements
Vehicules routiers - Connexions pour faisceaux de cdblage electrique
-
embarques
Partie 1: Languettes pour raccordements unipolaires - Dimensions et
exigences particulieres
Reference number
IS0 8092-1 :I 996(E)
---------------------- Page: 7 ----------------------
SIST EN ISO 8092-1:2000
I
IS0 8092-1:1996(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 8092-1 was prepared by Technical Committee
ISODC 22, Road vehicles, Subcommittee SC 3, Electrical and electronic
equipment.
This second edition cancels and replaces the first edition
(IS0 8092-1 :I 9891, of which it constitutes a technical revision.
IS0 8092 consists of the following parts, under the general title Road ve-
hicles - Connections for on-board electrical wiring harnesses:
- Part I: Tabs for single-pole connections - Dimensions and specific
requirements
- Part 2: Definitions, test methods and general performance require-
ments
- Part 3: Tabs for multi-pole connections - Dimensions and specific
requirements
- Part 4: Pins for single- and multi-pole connections - Dimensions
and specific requirements
Annex A of this part of IS0 8092 is for information only.
Q IS0 1996
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher,
International Organization for Standardization
CH-1211 Geneve 20 Switzerland
Case Postale 56
Printed in Switzerland
ii
---------------------- Page: 8 ----------------------
SIST EN ISO 8092-1:2000
IS0 8092-1:1996(E)
INTERNATIONAL STANDARD 0 IS0
Road vehicles - Connections for on-board electrical
wiring harnesses -
Part 1:
Tabs for single-pole connections - Dimensions and
specific requirements
4 Dimensions
1 Scope
This part of IS0 8092 specifies dimensions for the
Tabs for single-pole connections shall conform to the
tabs of single-pole connections and specific require-
dimensions given in table 1 and figure 1.
ments, for on-board electrical wiring harnesses of
Details not specified are left to the manufacturer's
road vehicles, which can be fitted into female con-
choice.
tacts such as those given in annex A. It applies to
connectors designed to be disconnected after
mounting in the ve
...