SIST EN 4536-2:2009

Aerospace series - Bushes, plain in corrosion resisting steel with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series

SIST EN 4536-2:2009

Name:SIST EN 4536-2:2009   Standard name:Aerospace series - Bushes, plain in corrosion resisting steel with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series
Standard number:SIST EN 4536-2:2009   language:English language
Release Date:20-Aug-2009   technical committee:I13 - Imaginarni 13
Drafting committee:   ICS number:49.035 - Components for aerospace construction
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Buchsen aus korrosionsbeständigem Stahl, mit selbstschmierender Beschichtung, erhöhte Belastung - Teil 2: Maße und Belastungen - Inch ReiheSérie aérospatiale - Bagues en acier résistant à la corrosion à garniture autolubrifiante, charge élevée - Partie 2: Dimensions et charges - Série en inchesAerospace series - Bushes, plain in corrosion resisting steel with self-lubricating liner, elevated load - Part 2: Dimensions and loads - Inch series49.035Sestavni deli za letalsko in vesoljsko gradnjoComponents for aerospace constructionICS:Ta slovenski standard je istoveten z:EN 4536-2:2009SIST EN 4536-2:2009en01-oktober-2009SIST EN 4536-2:2009SLOVENSKI
STANDARD



SIST EN 4536-2:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 4536-2July 2009ICS 49.035 English VersionAerospace series - Bushes, plain in corrosion resisting steel withself-lubricating liner, elevated load - Part 2: Dimensions andloads - Inch seriesSérie aérospatiale - Bagues en acier résistant à lacorrosion à garniture autolubrifiante, charge élevée - Partie2: Dimensions et charges - Série en inchesLuft- und Raumfahrt - Buchsen aus korrosionsbeständigemStahl, mit selbstschmierender Beschichtung, erhöhteBelastung - Teil 2: Maße und Belastungen - Inch ReiheThis European Standard was approved by CEN on 23 April 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4536-2:2009: ESIST EN 4536-2:2009



EN 4536-2:2009 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Terms and definitions .44Requirements .44.1Configuration, dimensions, tolerances and mass .44.2Surface roughness .44.3Materials .54.4Surface treatment .55Designation . 126Marking . 127Technical specification . 128Design recommendation . 12 SIST EN 4536-2:2009



EN 4536-2:2009 (E) 3 Foreword This document (EN 4536-2:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2010, and conflicting national standards shall be withdrawn at the latest by January 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 4536-2:2009



EN 4536-2:2009 (E) 4 1 Scope This standard specifies the characteristics of plain bushes in corrosion resisting steel with self-lubricating liner, elevated load for aerospace applications.
The bushes are intended for use in fixed or moving parts of the aircraft structure and control mechanisms. They shall be used in the temperature range − 55 °C to 163 °C. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2311, Aerospace series — Bushes with self-lubricating liner — Technical specification EN 2424, Aerospace series — Marking of aerospace products EN 3161, Aerospace series — Steel FE-PM3801 (X5CrNiCu17-4) — Air melted, solution treated and precipitation treated, bar a or D ≤ 200 mm, Rm ≥ 930 MPa TR 4475, Aerospace series — Bearings and mechanical transmissions for airframe applications — Vocabulary 1)
ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual tolerance indications ISO 8075, Aerospace — Surface treatment of hardenable stainless steel parts 3 Terms and definitions For the purposes of this document, the terms and definitions given in TR 4475 apply. 4 Requirements
4.1 Configuration, dimensions, tolerances and mass According to Figure 1 and Tables 1 and 2. Dimensions apply after surface treatment. Dimensions and tolerances are expressed in millimetres (inches).
General tolerances shall be ISO 2768-m in accordance with ISO 2768-1. 4.2 Surface roughness
According to Figure 1.
1) Published as ASD Technical Report at the date of publication of this standard. SIST EN 4536-2:2009



EN 4536-2:2009 (E) 5 4.3 Materials Bush: Stainless steel according to EN 3161 Liner: Self-lubricating wear resistant material consistent with the requirements of EN 2311 4.4 Surface treatment
Code T: Passivation according to ISO 8075.
Key a Chamfer machined before bonding b Chamfer or radius at manufacturers option c Chamfer machined after bonding Figure 1 — Configuration SIST EN 4536-2:2009



EN 4536-2:2009 (E) 6 Table 1 — Dimensions and tolerances Diameter code a
d D a . Nominal diameter 0 − 0,025 0 − 0,013
± 2° (0 − 0.0010) (0 − 0.0005)
04 6,350 (0.2500) 6,388 (0.2515) 9,550 (0.3760) 0,50 to 0,75 (0.020 to 0.030) 15° 05 7,938 (0.3125) 7,976 (0.3140) 11,140 (0.4386) 06 9,525 (0.3750) 9,563 (0.3765) 12,730 (0.5012) 07 11,113 (0.4375) 11,151 (0.4390) 14,321 (0.5638) 08 12,700 (0.5000) 12,738 (0.5015) 15,913 (0.6265) 09 14,288 (0.5625) 14,326 (0.5640) 17,506 (0.6892) 10 15,875 (0.6250) 15,913 (0.6265) 20,681 (0.8142) 11 17,463 (0.6875) 17,501 (0.6890) 22,268 (0.8767) 12 19,050 (0.7500) 19,088 (0.7515) 23,858 (0.9393) 14 22,225 (0.8750) 22,263 (0.8765) 27,038 (1.0645) 16 25,400 (1.0000) 25,438 (1.0015) 30,221 (1.1898) 18 28,575 (1.1250) 28,613 (1.1265) 33,396 (1.3148) 20 31,750 (1.2500) 31,788 (1.2515) 36,571 (1.4398) 22 34,925 (1.3750) 34,963 (1.3765) 39,746 (1.5648) 24 38,100 (1.5000) 38,138 (1.5015) 44,508 (1.7523) 26 41,275 (1.6250) 41,313 (1.6265) 47,683 (1.8773) 28 44,450 (1.7500) 44,488 (1.7515) 50,858 (2.0023) 32 50,800 (2.0000) 50,838 (2.0015) 57,208 (2.2523) a Diameter code corresponds to nominal diameter d in 1/16 inch.
SIST EN 4536-2:2009



EN 4536-2:2009 (E) 7 Table 2 — Mass Dia-meter code a Length code b 005 006 007 008 009 010 011 012 014 016 018 020 022 024 028 l
00,25−
(00.010−) 3,97 4,76 5,56 6,35 7,14 7,94 8,73 9,53 11,11 12,70 14,29 15,88 17,46 19,05 22,23 (0.156) (0.188) (0.219) (0.250) (0.281)(0.313)(0.344)(0.375)(0.438)(0.500)(0.563) (0.625) (0.688)(0.750)(0.875
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27