SIST-TP ISO/TR 16806:2005

Pneumatic fluid power -- Cylinders -- Load capacity of pneumatic slides and their presentation method

SIST-TP ISO/TR 16806:2005

Name:SIST-TP ISO/TR 16806:2005   Standard name:Pneumatic fluid power -- Cylinders -- Load capacity of pneumatic slides and their presentation method
Standard number:SIST-TP ISO/TR 16806:2005   language:English language
Release Date:31-Oct-2005   technical committee:IHPV - Hydraulics and pneumatics
Drafting committee:   ICS number:23.100.20 - Cylinders
SLOVENSKI STANDARD
SIST-TP ISO/TR 16806:2005
01-november-2005
)OXLGQDWHKQLND±3QHYPDWLND±9DOML±,]UDþXQLQSULND]QRVLOQRVWLYRGLO
Pneumatic fluid power -- Cylinders -- Load capacity of pneumatic slides and their
presentation method
Transmissions pneumatiques -- Vérins -- Capacité de charge des unités de guidage
pneumatique et leur méthode de présentation
Ta slovenski standard je istoveten z: ISO/TR 16806:2003
ICS:
23.100.20 +LGUDYOLþQLYDOML Cylinders
SIST-TP ISO/TR 16806:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TP ISO/TR 16806:2005

---------------------- Page: 2 ----------------------

SIST-TP ISO/TR 16806:2005


TECHNICAL ISO/TR
REPORT 16806
First edition
2003-02-15

Pneumatic fluid power — Cylinders —
Load capacity of pneumatic slides and
their presentation method
Transmissions pneumatiques — Vérins — Capacité de charge des
unités de guidage pneumatique et leur méthode de présentation




Reference number
ISO/TR 16806:2003(E)
©
ISO 2003

---------------------- Page: 3 ----------------------

SIST-TP ISO/TR 16806:2005
ISO/TR 16806:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2003
or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

---------------------- Page: 4 ----------------------

SIST-TP ISO/TR 16806:2005
ISO/TR 16806:2003(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Rating factors . 2
4.1 Pressure containing capability. 2
4.2 Maximum axial load . 2
4.3 Maximum combined loading for a tool plate, and its deflections. 2
5 Presentation of ratings. 3
5.1 Sketch of loading on tool plate. 3
5.2 Tabulations . 4
5.3 Graph. 5
5.4 Calculation formulas. 5
5.5 Nominal ratings .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27