|
SIST EN 3052:2009
01-oktober-2009
1DGRPHãþD
SIST EN 3052:2001
Aeronavtika - Sorniki, normalna šestroba glava, ozka toleranca, kratek navoj, iz
toplotno in korozijsko odpornega jekla, pasivirani - Klasifikacija: 1100 MPa (pri
temperaturi okolice)/425 °C
Aerospace series - Bolts, normal hexagonal head, close tolerance normal shank, short
thread, in heat and corrosion resisting steel, passivated - Classification: 1100 MPa (at
ambient temperature)/425 °C
Luft- und Raumfahrt - Sechskant-Paßschrauben, kurzes Gewinde, aus
korrosionsbeständigem und hochwarmfestem Stahl, passiviert - Klasse: 1100 MPa (bei
Raumtemperatur)/425 °C
Série aérospatiale - Vis à tête hexagonale normale, fût normal à tolérance serrée,
filetage court, en acier résistant à chaud et à la corrosion, passivées - Classification:
1100 MPa (à température ambiante)/425 °C
Ta slovenski standard je istoveten z: EN 3052:2009
ICS:
49.030.20 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN 3052:2009 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 3052:2009
---------------------- Page: 2 ----------------------
SIST EN 3052:2009
EUROPEAN STANDARD
EN 3052
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2009
ICS 49.030.20 Supersedes EN 3052:1993
English Version
Aerospace series - Bolts, normal hexagonal head, close
tolerance normal shank, short thread, in heat and corrosion
resisting steel, passivated - Classification: 1 100 MPa (at
ambient temperature) / 425 °C
Série aérospatiale - Vis à tête hexagonale normale, fût Luft- und Raumfahrt - Sechskant-Paßschrauben, kurzes
normal à tolérance serrée, filetage court, en acier résistant Gewinde, aus korrosionsbeständigem und
à chaud et à la corrosion, passivées - Classification: 1 100 hochwarmfestem Stahl, passiviert - Klasse: 1 100 MPa (bei
MPa (à température ambiante) / 425 °C Raumtemperatur) / 425 °C
This European Standard was approved by CEN on 13 June 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3052:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 3052:2009
EN 3052:2009 (E)
Contents Page
Foreword . 3
1 Scope . 4
2 Normative references . 4
3 Required characteristics . 4
4 Designation. 7
5 Marking . 7
6 Technical specification . 7
7 Oversized bolts . 7
2
---------------------- Page: 4 ----------------------
SIST EN 3052:2009
EN 3052:2009 (E)
Foreword
This document (EN 3052:2009) has been prepared by the Aerospace and Defence Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2010, and conflicting national standards shall be withdrawn
at the latest by January 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 3052:1993.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 3052:2009
EN 3052:2009 (E)
...