|
SIST EN ISO 6508-2:2015
01-maj-2015
1DGRPHãþD
SIST EN ISO 6508-2:2006
Kovinski materiali - Preskus trdote po Rockwellu - 2. del: Preverjanje in umerjanje
naprav za preskušanje (ISO 6508-2:2015)
Metallic materials - Rockwell hardness test - Part 2: Verification and calibration of testing
machines and indenters (ISO 6508-2:2015)
Metallische Werkstoffe - Härteprüfung nach Rockwell - Teil 2: Prüfung und Kalibrierung
der Prüfmaschinen und Eindringkörper (ISO 6508-2:2015)
Matériaux métalliques - Essai de dureté Rockwell - Partie 2: Vérification et étalonnage
des machines d'essai (ISO 6508-2:2015)
Ta slovenski standard je istoveten z: EN ISO 6508-2:2015
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
SIST EN ISO 6508-2:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6508-2:2015
---------------------- Page: 2 ----------------------
SIST EN ISO 6508-2:2015
EUROPEAN STANDARD
EN ISO 6508-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2015
ICS 77.040.10 Supersedes EN ISO 6508-2:2005
English Version
Metallic materials - Rockwell hardness test - Part 2: Verification
and calibration of testing machines and indenters (ISO 6508-
2:2015)
Matériaux métalliques - Essai de dureté Rockwell - Partie 2: Metallische Werkstoffe - Härteprüfung nach Rockwell - Teil
Vérification et étalonnage des machines d'essai et des 2: Überprüfung und Kalibrierung der Prüfmaschinen und
pénétrateurs (ISO 6508-2:2015) Eindringkörper (ISO 6508-2:2015)
This European Standard was approved by CEN on 10 January 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6508-2:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 6508-2:2015
EN ISO 6508-2:2015 (E)
Contents
Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 6508-2:2015
EN ISO 6508-2:2015 (E)
Foreword
This document (EN ISO 6508-2:2015) has been prepared by Technical Committee ISO/TC 164 "Mechanical
testing of metals" in collaboration with Technical Committee ECISS/TC 101 “Test methods for steel (other
than chemical analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2015, and conflicting national standards shall be
withdrawn at the latest by September 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6508-2:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 6508-2:2015 has been approved by CEN as EN ISO 6508-2:2015 without any modification.
3
----------------------
...