|
SIST-TS CEN ISO/TS 25377:2007
01-december-2007
1DYRGLOD]DGRORþHYDQMHPHULOQHQHJRWRYRVWLYKLGURPHWULML,6276
Hydrometric uncertainty guidance (HUG) (ISO/TS 25377:2007)
Leitfaden zu Messunsicherheiten in der Hydrometrie (HUG) (ISO/TS 25377:2007)
Lignes directrices relatives a l'incertitude en hydrométrie (ISO/TS 25377:2007)
Ta slovenski standard je istoveten z: CEN ISO/TS 25377:2007
ICS:
17.120.20 Pretok v odprtih kanalih Flow in open channels
SIST-TS CEN ISO/TS 25377:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
TECHNICAL SPECIFICATION
CEN ISO/TS 25377
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
October 2007
ICS 17.120.20
English Version
Hydrometric uncertainty guidance (HUG) (ISO/TS 25377:2007)
Lignes directrices relatives à l'incertitude en hydrométrie Leitfaden zu Messunsicherheiten in der Hydrometrie (HUG)
(ISO/TS 25377:2007) (ISO/TS 25377:2007)
This Technical Specification (CEN/TS) was approved by CEN on 2 August 2007 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 25377:2007: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
CEN ISO/TS 25377:2007 (E)
Contents Page
Foreword.3
2
---------------------- Page: 3 ----------------------
CEN ISO/TS 25377:2007 (E)
Foreword
This document (CEN ISO/TS 25377:2007) has been prepared by Technical Committee CEN/TC 318
"Hydrometry", the secretariat of which is held by BSI, in collaboration with Technical Committee ISO/TC 113
"Hydrometric determinations".
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 4 ----------------------
TECHNICAL ISO/TS
SPECIFICATION 25377
First edition
2007-10-01
Hydrometric uncertainty guidance (HUG)
Lignes directrices relatives à l'incertitude en hydrométrie
Reference number
ISO/TS 25377:2007(E)
©
ISO 2007
---------------------- Page: 5 ----------------------
ISO/TS 25377:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
or by any means,
electronic or mechanical, including photocopying and microfilm, without perm
...