|
STANDARDSIST EN 486:19981DGRPHãþD
SIST EN 486:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 486August 2009ICS 77.150.10Supersedes EN 486:1993
English VersionAluminium and aluminium alloys - Extrusion ingots -SpecificationsAluminium et alliages d'aluminium - Billettes de filage -SpécificationsAluminium und Aluminiumlegierungen - Pressbarren -SpezifikationenThis European Standard was approved by CEN on 24 July 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 486:2009: ESIST EN 486:2009
EN 486:2009 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Terms and definitions .44Ordering information .45Requirements .55.1Production and manufacturing processes .55.2Chemical composition .55.3Surface and internal quality .55.4Tolerances on dimensions .66Test procedures .66.1Analysis of chemical composition .66.2Homogenizing treatment .76.3Other tests .77Inspection documents .77.1Certificate of mass and analysis .77.2Inspection certificate .78Marking .79Packaging, transport and storage .810Complaints .8Bibliography .9 SIST EN 486:2009
EN 486:2009 (E) 3 Foreword This document (EN 486:2009) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2010, and conflicting national standards shall be withdrawn at the latest by February 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 486:1993. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 2 "Extrusion billets and rolling ingots" to revise EN 486:1993. CEN/TC 132 affirms its policy that in the case when a patentee refuses to grant licences on standardised standard products under reasonable and not discriminatory conditions, then this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 486:2009
EN 486:2009 (E) 4 1 Scope This European Standard specifies the general requirements to be met by extrusion ingots of aluminium and aluminium alloys obtained by semi-continuous or continuous casting, from primary or recycled metal, for general engineering applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 573-1, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 1: Numerical designation system EN 573-2, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 2: Chemical symbol based designation system EN 573-3, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 3: Chemical composition EN 10204, Metallic products — Types of inspection documents EN 12258-1:1998, Aluminium and aluminium alloys — Terms and definitions — Part 1: General terms EN 14242, Aluminium and aluminium alloys — Chemical analysis — Inductively coupled plasma optical emission spectral analysis EN 14726, Aluminium and aluminium alloys
...