|
SIST EN 487:2009
01-oktober-2009
1DGRPHãþD
SIST EN 487:1998
Aluminij in aluminijeve zlitine - Brame za valjanje - Specifikacije
Aluminium and aluminium alloys - Rolling ingots - Specifications
Aluminium und Aluminiumlegierungen - Walzbarren - Spezifikationen
Aluminium et alliages d'aluminium - Plaques de laminage - Spécifications
Ta slovenski standard je istoveten z: EN 487:2009
ICS:
77.150.10 Aluminijski izdelki Aluminium products
SIST EN 487:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 487:2009
---------------------- Page: 2 ----------------------
SIST EN 487:2009
EUROPEAN STANDARD
EN 487
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2009
ICS 77.150.10 Supersedes EN 487:1993
English Version
Aluminium and aluminium alloys - Rolling ingots - Specifications
Aluminium et alliages d'aluminium - Plaques de laminage - Aluminium und Aluminiumlegierungen - Walzbarren -
Spécifications Spezifikationen
This European Standard was approved by CEN on 24 July 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 487:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 487:2009
EN 487:2009 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Ordering information .4
5 Requirements .5
5.1 Production and manufacturing processes .5
5.2 Chemical composition .5
5.3 Surface and internal quality .6
5.4 Tolerances on dimensions .6
5.5 Tolerances of form.7
5.6 Sawing .9
5.7 Scalping .9
6 Test procedures .9
6.1 Analysis of chemical composition .9
6.2 Inspection of physical and metallurgical properties. 10
6.3 Other tests . 10
7 Inspection documents . 10
7.1 Certificate of mass and analysis . 10
7.2 Inspection certificate . 10
8 Marking . 11
8.1 General . 11
8.2 Edge marking . 11
8.3 Top end marking . 11
9 Packaging, transport and storage . 11
10 Complaints . 12
Bibliography . 13
2
---------------------- Page: 4 ----------------------
SIST EN 487:2009
EN 487:2009 (E)
Foreword
This document (EN 487:2009) has been prepared by Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2010, and conflicting national standards shall be withdrawn
at the latest by February 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 487:1993.
Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 2 "Extrusion
billets and rolling ingots" to revise EN 487:1993.
CEN/TC 132 affirms its policy that in the case when a patentee refuses to grant licences on standardised
standard products under reasonable and not discriminatory conditions, then this product shall be removed
from the corresponding standard.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 487:2009
EN 487:2009 (E)
1 Scope
This European Standard specifies the general requirements to be met by rolling ingots of aluminium or
aluminium alloys obtained by semi-continuous vertical casting.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 573-1, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 1:
Numerical designation system
EN 573-2, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 2:
Chemical symbol based designation system
EN 573-3, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 3:
Chemical composition
EN 10204, Metallic products — Types of inspection documents
EN 12258-1:1998, Aluminium and aluminium alloys — Terms and definitions — Part 1: General terms
EN 14242, Aluminium and aluminium alloys — Chemical analysis — Inductively coupled plasma optical
emission spectral analysis
EN 14726, Aluminium and aluminium alloys — Chemical analysis — Guideline for spark optical emission
spectrometric analysis
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following
apply.
3.1
heat
quantity of liquid metal that has simultaneously undergone the same preparatory treatment in the furnace
before the casting operation
4 Ordering information
The ordering information shall define the product required and shall contain the following:
a) the form of the product (rolling ingot);
b) the designation of the aluminium or aluminium alloy according to EN 573-1 and 573-2 (or the purchaser
alloy designation after agreement between supplier and purchaser). Tighter limits than the composition
limits stated in EN 573-3 may be specified as required;
c) whether as cast or homogenized. The homogenizing parameters should be agreed between the supplier
and the purchaser;
4
---------------------- Page: 6 ----------------------
SIST EN 487:2009
EN 487:2009 (E)
d) the number of this European Standard;
e) the dimensions and shape of the product:
1) nominal thickness (expressed in millimetres);
2) nominal width (expressed in millimetres);
3) nominal length and tolerance if different from standard (expressed in millimetres);
4) cross sectional profile details or drawing number (expressed in millimetres);
f) sawing code (see 5.6.4);
g) whether rolling ingots are to be supplied scalped or not;
h) whether the rolling ingots are scalped or not before hot rolling;
i) end use (e.g. foil, packaging) (see 5.1);
j) quantity:
1) mass (in metric tonnes) or number of pieces;
2) quantity tolerances if required;
k) any requirements for inspection documents (see Clause 7);
l) any additional requirements agreed between supplier and purchaser (see Clause 7).
5 Requirements
5.1 Production and manufacturing processes
The product requirements as formulated in this clause normally are not sufficient for rolling ingots to meet the
purchaser's requirements for rolled products. Therefore, the purchaser shall give the manufacturer full details
concerning the end use requirements, so that the manufacturing conditions of the manufacturer may best be
adjusted to fulfil the requirements.
It is recommended that trial quantities be produced to confirm that the end use requirements are met. It is also
recommended that the purchaser asks the manufacturer to advise of any significant change in the
manufacturing processes which may affect the quality of the final pro
...