|
STANDARD
SIST EN 61076-3-117:2009
EUROPEAN STANDARD EN 61076-3-117 NORME EUROPÉENNE
EUROPÄISCHE NORM August 2009
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: Avenue Marnix 17, B - 1000 Brussels
© 2009 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61076-3-117:2009 E
ICS 31.220.10
English version
Connectors for electronic equipment -
Product requirements -
Part 3-117: Rectangular connectors -
Detail specification for protective housings
for use with 8-way shielded and unshielded connectors
for industrial environments incorporating the IEC 60603-7 series interface -
Variant 14 related to IEC 61076-3-106 -
Push pull coupling (IEC 61076-3-117:2009)
Connecteurs
pour équipement électroniques -
Exigences de produits -
Partie 3-117: Connecteurs rectangulaires -
Spécification particulière
pour boîtiers de protection utilisés
avec des connecteurs blindés et non blindés
à 8 voies dans des environnements industriels incorporant l’interface série CEI 60603-7 -
Variante 14 liée à la CEI 61076-3-106 -
Type d’accouplement pousser-tirer (CEI 61076-3-117:2009) Steckverbinder
für elektronische Einrichtungen - Produktanforderungen -
Teil 3-117: Rechteckige Steckverbinder - Bauartspezifikation für Schutzgehäuse
für die Anwendung mit 8-poligen geschirmten
und ungeschirmten Steckverbindern
für industrielle Umgebungen zur Aufnahme
der Schnittstelle der Reihe IEC 60603-7 - Ausführung 14 zu IEC 61076-3-106 -
Push-pull-Kupplung (IEC 61076-3-117:2009)
This European Standard was approved by CENELEC on 2009-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 61076-3-117:2009
EN 61076-3-117:2009
- 2 -
Foreword The text of document 48B/1996/FDIS, future edition 1 of IEC 61076-3-117, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61076-3-117 on 2009-07-01. The following dates were fixed: – latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop)
2010-04-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2012-07-01 Annex ZA has been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 61076-3-117:2009 was approved by CENELEC as a European Standard without any modification. __________
SIST EN 61076-3-117:2009
- 3 - EN 61076-3-117:2009 Annex ZA (normative)
Normative references to international publications with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60050-581 2008 International Electrotechnical Vocabulary (IEV) -
Part 581: Electromechanical components for electronic equipment - -
IEC 60068-1 -1) Environmental testing -
Part 1: General and guidance EN 60068-1 19942)
IEC 60068-2-14 -1) Environmental testing -
Part 2-14: Tests - Test N: Change of temperature EN 60068-2-14 20092)
IEC 60068-2-30 -1) Environmental testing -
Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) EN 60068-2-30 20052)
IEC 60512 Series Connectors for electronic equipment -
Tests and measurements
EN 60512 Series
IEC 60512-1-100 -1) Connectors for electronic equipment -
Tests and measurements -
Part 1-100: General - Applicable publications EN 60512-1-100 20062)
IEC 60529 1989 Degrees of protection provided by enclosures (IP Code) EN 60529 + corr. May
1991 1993
IEC 60603-7 Series Connectors for electronic equipment
EN 60603-7 Series
IEC 60664-1 -1) Insulation coordination for equipment within low-voltage systems -
Part 1: Principles, requirements and tests EN 60664-1 20072)
IEC 61076-1 2006 Connectors for electronic equipment -
Product requirements -
Part 1: Generic specification EN 61076-1 2006
IEC 61156 Series Multicore and symmetrical pair/quad cables for digital communications
- -
1) Undated reference. 2) Valid edition at date of issue. SIST EN 61076-3-117:2009
SIST EN 61076-3-117:2009
IEC 61076-3-117Edition 1.0 2009-04INTERNATIONAL STANDARD NORME INTERNATIONALEConnectors for electronic equipment – Product requirements –
Part 3-117: Rectangular connectors –Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface – Variant 14 related to IEC 61076-3-106 – Push-pull coupling
Connecteurs pour équipements électroniques – Exigences de produit –
Partie 3-117: Connecteurs rectangulaires – Spécification particulière pour boîtiers de protection utilisés avec des connecteurs blindés et non blindés à 8 voies dans des environnements industriels incorporant l’interface série
CEI 60603-7 – Variante 14 liée à la CEI 61076-3-106 – Type d’accouplement
pousser-tirer
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE RICS 31.220.10 PRICE CODECODE PRIXISBN 2-8318-1038-5
Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale SIST EN 61076-3-117:2009
– 2 – 61076-3-117 © IEC:2009 CONTENTS FOREWORD.4 1 Scope.6 2 General data.6 2.1 Normative references.6 2.2 Terms and definitions.7 3 Dimensional information.7 3.1 Common features.7 3.2 General.7 3.3 Contact arrangement of all connector types.7 3.4 IP65 and IP67 sealing.7 3.5 Dimensions, fixed connector.8 3.6 Dimensions, free connector.9 3.7 Termination and mounting information.9 3.7.1 General.9 3.7.2 Mounting information for fixed connector.9 4 Gauges.10 4.1 Connectors, IEC 60603-7 interface.10 5 Characteristics.10 5.1 Climatic category.10 5.2 Electrical characteristics.10 5.2.1 Clearance and creepage distances.10 5.2.2 Voltage proof.11 5.2.3 Current-carrying capacity.11 5.2.4 Mating cycles with power applied.11 5.2.5 Initial contact resistance.11 5.2.6 Input to output resistance.11 5.2.7 Resistance unbalance.11 5.2.8 Initial insulation resistance.12 5.3 Transmission characteristics.12 5.3.1 General.12 5.4 Mechanical.12 5.4.1 Mechanical operation.12 5.4.2 Effectiveness of connector coupling devices transversal.12 5.4.3 Effectiveness of connector coupling devices.12 5.4.4 Engagement and separation forces.12 6 Test schedule.12 6.1 General.12 6.2 Test procedures and measuring methods.13 6.3 Preconditioning.13 6.4 Wiring and mounting of specimens.13 6.4.1 Wiring.13 6.4.2 Mounting.13 6.5 Arrangement for contact resistance test.13 6.6 Arrangement for dynamic stress tests (test phase AP2).13 6.7 Basic (minimum) test schedule.13 6.8 Full test schedule.14 SIST EN 61076-3-117:2009
61076-3-117 © IEC:2009 – 3 – 6.8.1 General.14 6.8.2 Test group P – Preliminary.14 6.8.3 Test group P.14 6.8.4 Test group AP.15 6.8.5 Test group BP.16 6.8.6 Test group CP.17 6.8.7 Test group DP – Electrical load and temperature.18 6.8.8 Test group EP – Signal integrity.18
Figure 1 – Fixed connector.8 Figure 2 – Free connector.9 Figure 3 – Mounting information – panel cut-out outline.9
Table 1 – Dimensions, fixed connector.8 Table 2 – Dimensions, free connector.9 Table 3 – Mounting information.10 Table 4 – Climatic categories – selected values for environmental performance level A.10 Table 5 – Clearance and creepage distances.11 Table 6 – Test group P.14 Table 7 – Test group AP – Dynamic/climatic.15 Table 8 – Test group BP – Mechanical.16 Table 9 – Test group CP – Continuity.17
SIST EN 61076-3-117:2009
– 4 – 61076-3-117 © IEC:2009 INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
CONNECTORS FOR ELECTRONIC EQUIPMENT –
PRODUCT REQUIREMENTS –
Part 3-117: Rectangular connectors –
Detail specification for protective housings
for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface –
Variant 14 related to IEC 61076-3-106 –
Push-pull coupling
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61076-3-117 has been prepared by subcommittee 48B: Connectors, of IEC technical committee 48: Electromechanical components and mechanical structures for electronic equipment. This International Standard cancels and replaces IEC/PAS 61076-3-117 (2006). SIST EN 61076-3-117:2009
61076-3-117 © IEC:2009 – 5 – The text of this standard is based on the following documents: FDIS Report on voting 48B/1996/FDIS 48B/2014/RVD
Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of IEC 61076 series, under the general title Connectors for electronic equipment – Product requirements, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be
• reconfirmed,
...