SIST EN 3148:2008

Aerospace series - Shank nuts, self-locking, flange restrained - Installation procedure

SIST EN 3148:2008

Name:SIST EN 3148:2008   Standard name:Aerospace series - Shank nuts, self-locking, flange restrained - Installation procedure
Standard number:SIST EN 3148:2008   language:English language
Release Date:22-May-2008   technical committee:I13 - Imaginarni 13
Drafting committee:   ICS number:49.030.30 - Nuts
SLOVENSKI STANDARD
SIST EN 3148:2008
01-julij-2008
$HURQDYWLND=DNRYLþHQHPDWLFHVDPRYDURYDOQH]]DGUåHYDOQRSULUREQLFR
3RVWRSHNYJUDGQMH
Aerospace series - Shank nuts, self-locking, flange restrained - Installation procedure
Luft- und Raumfahrt - Einnietmuttern, selbstsichernd, mit Anlagefläche - Einbauverfahren
Série aérospatiale - Écrous à sertir, auto-freinants, à flancs de retenue - Procédure
d'installation
Ta slovenski standard je istoveten z: EN 3148:2008
ICS:
49.030.30 Matice Nuts
SIST EN 3148:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 3148
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2008
ICS 49.030.30

English Version
Aerospace series - Shank nuts, self-locking, flange restrained -
Installation procedure
Série aérospatiale - Écrous à sertir, auto-freinants, à flancs Luft- und Raumfahrt - Einnietmuttern, selbstsichernd, mit
de retenue - Procédure d'installation Anlagefläche - Einbauverfahren
This European Standard was approved by CEN on 12 December 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3148:2008: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 3148:2008 (E)
Contents Page
Foreword.3
1 Scope.4
2 Normative references.4
3 Swaging procedure.4
4 Swaging tool dimensions .5
5 Controlling alter swaging.7

2

---------------------- Page: 3 ----------------------

EN 3148:2008 (E)
Foreword
This document (EN 3148:2008) has been prepared by the Aerospace and Defence Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at
the latest by October 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
3

---------------------- Page: 4 ----------------------

EN 3148:2008 (E)
1 Scope
This process standard details the installation of sh
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27