|
SIST EN 302 217-3 V1.3.1:2009
01-november-2009
)LNVQLUDGLMVNLVLVWHPL.DUDNWHULVWLNHLQ]DKWHYH]DRSUHPRLQDQWHQHWLSDWRþND
WRþNDGHO2SUHPDNLGHOXMHYIUHNYHQþQLKSDVRYLKNMHUVHODKNRXSRUDEOMD
XVNODMHQDLQQHXVNODMHQDRSUHPD+DUPRQL]LUDQL(1NL]DMHPDELVWYHQH]DKWHYH
þOHQDGLUHNWLYH5 77(
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment
and antennas - Part 3: Equipment operating in frequency bands where both frequency
coordinated or uncoordinated deployment might be applied - Harmonized EN covering
the essential requirements of article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 302 217-3 Version 1.3.1
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
33.120.40 Antene Aerials
SIST EN 302 217-3 V1.3.1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 302 217-3 V1.3.1:2009
---------------------- Page: 2 ----------------------
SIST EN 302 217-3 V1.3.1:2009
ETSI EN 302 217-3 V1.3.1 (2009-07)
Harmonized European Standard (Telecommunications series)
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 3: Equipment operating in frequency bands where
both frequency coordinated or
uncoordinated deployment might be applied;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 3 ----------------------
SIST EN 302 217-3 V1.3.1:2009
2 ETSI EN 302 217-3 V1.3.1 (2009-07)
Reference
REN/ATTM-04003
Keywords
DFRS, digital, DRRS, FWA, point-to-point, radio,
regulation, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 302 217-3 V1.3.1:2009
3 ETSI EN 302 217-3 V1.3.1 (2009-07)
Contents
Intellectual Property Rights . 7
Foreword . 7
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 12
3.3 Abbreviations . 12
4 Technical requirements specifications . 12
4.1 Environmental profile . 13
4.2 RF-channel selection . 13
4.2.1 RF-channel selection procedure . 13
4.2.2 Interference avoidance requirements . 13
4.2.2.1 Interference avoidance limit . 13
4.2.3 Frequency agile automatic channel selectio n . 14
4.3 Transmitter requirements . 14
4.3.1 Transmitter power . 14
4.3.1.1 Transmitter power . 14
4.3.1.2 Equivalent Isotropically Radiated Power (EIRP) . 14
4.3.1.3 Output Power Tolerance . 14
4.3.2 Radio Frequency (RF) spectrum mask. 14
4.3.3 Spurious emissions . 15
4.3.4 Radio frequency tolerance . 15
4.3.5 Antenna directional requirements . 15
4.3.5.1 Radiation Pattern Envelope (Off-axis EIRP density) . 15
4.3.5.2 Antenna gain . 15
4.3.5.3 Antenna Cross-Polar Discrimination (XPD) . 16
4.4 Receiver requirements . 16
4.4.1 Spurious emissions . 16
5 Testing for compliance with technical requirements . 16
5.1 Environmental conditions for testing . 16
5.2 RF-channel selection . 17
5.3 Essential radio test suites for the transmitter . 17
5.3.1 Transmitter power . 18
5.3.1.1 Transmitter power . 18
5.3.1.2 Equivalent Isotropically Radiated Power (EIRP) and EIRP density mask . 18
5.3.1.3 Output power tolerance . 18
5.3.2 RF spectrum mask . 18
5.3.3 Spurious emissions - external . 18
5.3.4 Radio frequency tolerance . 18
5.3.5 Antenna and system directional requirements . 19
5.3.5.1 Radiation pattern envelope (Off-axis EIRP density) . 19
5.3.5.2 Antenna gain . 19
5.3.5.3 Antenna Cross-Polar Discrimination (XPD) . 19
5.4 Essential radio test suites for the receiver . 19
5.4.1 Spurious emissions . 20
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT) . 21
ETSI
---------------------- Page: 5 ----------------------
SIST EN 302 217-3 V1.3.1:2009
4 ETSI EN 302 217-3 V1.3.1 (2009-07)
Annex B (normative): Wide radio-frequency band covering units and multirate equipment
specification and tests . 23
B.1 Wide radio-frequency band covering units . 23
B.2 Multirate/multiformat equipment . 25
Annex C (informative): The EN title in the official languages . 26
Annex D (informative): Bibliography . 27
Annex UA (normative): Frequency band around 58 GHz . 28
UA.0 Introduction . 28
UA.1 Digital systems . 28
UA.1.1 Frequency bands and channel arrangements . 28
UA.1.1.1 Frequency band . 28
UA.1.1.2 Radio channel arrangements . 28
UA.1.1.3 Transmission capacity. 28
UA.1.2 Transmitter . 29
UA.1.2.1 Transmitter power . 29
UA.1.2.2 Equivalent Isotropically Radiated Power (EIRP) . 29
UA.1.2.3 Output power tolerance . 29
UA.1.2.4 RF spectrum masks . 29
UA.1.2.4.1 Limits . 29
UA.1.2.4.2 Spectrum analyser settings . 30
UA.1.2.5 Spurious emissions-external . 30
UA.1.2.6 Radio frequency tolerance . 30
UA.1.2.7 RF-channel selection parameters . 30
UA.1.3 Receiver . 30
UA.2 Analogue systems . 31
UA.2.1 Frequency bands and channel arrangements . 31
UA.2.1.1 Frequency band . 31
UA.2.1.2 Radio channel arrangements . 31
UA.2.1.3 Transmission capacity. 31
UA.2.2 Transmitter . 31
UA.2.2.1 Transmitter power . 31
UA.2.2.2 Equivalent Isotropically Radiated Power (EIRP) . 31
UA.2.2.3 Output power tolerance . 31
UA.2.2.4 RF spectrum masks . 31
UA.2.2.5 Spurious emissions - external . 31
UA.2.2.6 RF frequency tolerance . 31
UA.2.3 Receiver requirements . 32
UA.2.3.1 Spurious emissions . 32
Annex UB (normative): Frequency band 64 GHz to 66 GHz . 33
UB.0 Introduction . 33
UB.1 Frequency bands and channel arrangements . 33
UB.1.1 Frequency band . 33
UB.1.2 Radio channel arrangements. 34
UB.1.3 Spectral efficiency . 34
UB.2 Transmitter . 35
UB.2.1 Transmitter power and Equivalent Isotropically Radiated Power (EIRP) . 35
UB.2.2 Output power tolerance . 36
UB.2.3 EIRP density masks . 37
UB.2.3.1 Limits . 37
UB.2.3.2 Emissions outside the 64 GHz to 66 GHz range . 38
UB.2.3.3 Spectrum analyser settings . 38
UB.2.4 Spurious emissions . 38
UB.2.5 Radio frequency tolerance . 38
ETSI
---------------------- Page: 6 ----------------------
SIST EN 302 217-3 V1.3.1:2009
5 ETSI EN 302 217-3 V1.3.1 (2009-07)
UB.2.6 RF-channel selection parameters . 38
UB.2.7 Antenna gain . 38
UB.3 Receiver . . 38
Annex UBa (normative): Frequency band 57 GHz to 66 GHz for point-to-point fixed wireless
systems . 39
UBa.0 Introduction . 39
UBa.1 Frequency bands and channel arrangements . 39
UBa.1.1 Frequency band . 39
UBa.1.2 Radio channel arrangements and nominal bandwidth . 40
UBa.1.3 Spectral efficiency . 40
UBa.2 Transmitter . 41
UBa.2.1 Transmitter power, antenna gain and Equivalent Isotropically Radiated Power (EIRP) . 41
UBa.2.2 Output power tolerance . 42
UBa.2.3 RF spectrum masks . 43
UBa.2.3.1 Limits . 43
UBa.2.3.2 Emissions outside the 57 GHz to 66 GHz range . 44
UBa.2.4 Spurious emissions . 45
UBa.2.5 Radio frequency tolerance . 45
UBa.2.6 Antenna gain . 45
UBa.3 Receiver . 45
Annex UC (normative): Frequency bands 71 GHz to 76 GHz and 81 GHz to 86 GHz . 46
UC.0 Introduction . 46
UC.1 Frequency bands and channel arrangements . 46
UC.1.1 Frequency band . 46
UC.1.2 Radio channel arrangements. 46
UC.1.3 Spectral occupancy and transmission capacity . 47
UC.2 Transmitter . 47
UC.2.1 Transmitter power and Equivalent Isotropic Radiated Power (EIRP) . 47
UC.2.2 Output power tolerance . 48
UC.2.3 Output power density masks . 49
UC.2.3.1 Limits . 49
UC.2.3.2 Emissions outside the 71 GHz to 76 GHz and 81 GHz to 86 GHz ranges. 50
UC.2.3.2.1 General requirement . 50
UC.2.3.2.2 Requirement for emissions above 86 GHz band edge . 50
UC.2.3.2.3 Conformance statement . 51
UC.2.3.3 Spectrum analyser settings . 51
UC.2.4 Spurious emissions-external . 51
UC.2.5 Radio frequency tolerance . 51
UC.2.6 RF-channel selection parameters . 51
UC.2.7 Antenna gain . 51
UC.3 Receiver . . 51
Annex UD (informative): Rationale for the interference limit formula . 52
UD.1 Analysis of the quality value for the channel selection procedure . 52
UD.1.1 Error-performance and availability requirements for Class A equipment . 52
UD.1.1.1 Example in the 58 GHz band . 52
UD.1.2 Theoretical background . 52
UD.1.3 Typical co-channel interference situation when channel rejection threshold is used . 53
UD.2 Protection capability of the RF-channel selection procedure . 54
UD.3 Frequency agility criteria. 55
ETSI
---------------------- Page: 7 ----------------------
SIST EN 302 217-3 V1.3.1:2009
6 ETSI EN 302 217-3 V1.3.1 (2009-07)
Annex UE (informative): Capacity and Receiver characteristics in the bands 64 GHz to
66 GHz, 71 GHz to 76 GHz and 81 GHz to 86 GHz. 56
UE.1 Band 64 GHz to 66 GHz . . 56
UE.1.1 BER as a function of receiver input signal level (RSL) . 56
UE.1.2 Co-channel and adjacent channel interference sensitivity . 57
UE.1.3 CW spurious interference . 57
UE.2 Bands 71 GHz to 76 GHz and 81 GHz to 86 GHz . 57
UE.2.1 Capacity . 57
UE.2.2 BER as a function of receiver input signal level (RSL) . 58
UE.2.3 Co-channel and adjacent channel interference sensitivity . 59
UE.2.4 CW spurious interference . 59
History . 60
ETSI
---------------------- Page: 8 ----------------------
SIST EN 302 217-3 V1.3.1:2009
7 ETSI EN 302 217-3 V1.3.1 (2009-07)
Intellectual Property
...