|
SIST EN ISO 13000-1:2006
01-april-2006
1DGRPHãþD
SIST EN ISO 13000-1:1999
3ROLPHUQLPDWHULDOL±3ROL]GHONLL]SROLWHWUDIOXRURHWLOHQD37)(±GHO=DKWHYHLQ
R]QDþHYDQMH,62',6
Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements
and designation (ISO 13000-1:2005)
Kunststoffe - Polytetrafluorethylen (PTFE)-Halbzeuge - Teil 1: Anforderungen und
Bezeichnung (ISO 13000-1:2005)
Plastiques - Semi-produits en polytétrafluoroéthylene (PTFE) - Partie 1: Spécifications et
désignation (ISO 13000-1:2005)
Ta slovenski standard je istoveten z: EN ISO 13000-1:2005
ICS:
83.140.01 Izdelki iz gume in polimernih Rubber and plastics products
materialov na splošno in general
SIST EN ISO 13000-1:2006 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13000-1:2006
---------------------- Page: 2 ----------------------
SIST EN ISO 13000-1:2006
EUROPEAN STANDARD
EN ISO 13000-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2005
ICS 83.140.01 Supersedes EN ISO 13000-1:1997
English Version
Plastics - Polytetrafluoroethylene (PTFE) semi-finished products
- Part 1: Requirements and designation (ISO 13000-1:2005)
Plastiques - Semi-produits en polytétrafluoroéthylène Kunststoffe - Polytetrafluorethylen (PTFE)-Halbzeuge - Teil
(PTFE) - Partie 1: Spécifications et désignation (ISO 1: Anforderungen und Bezeichnung (ISO 13000-1:2005)
13000-1:2005)
This European Standard was approved by CEN on 4 November 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13000-1:2005: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13000-1:2006
EN ISO 13000-1:2005 (E)
Foreword
This document (EN ISO 13000-1:2005) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of
which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2006, and conflicting national standards
shall be withdrawn at the latest by May 2006.
This document supersedes EN ISO 13000-1:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 13000-1:2005 has been approved by CEN as EN ISO 13000-1:2005 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13000-1:2006
INTERNATIONAL ISO
STANDARD 13000-1
Second edition
2005-11-15
Plastics — Polytetrafluoroethylene
(PTFE) semi-finished products —
Part 1:
Requirements and designation
Plastiques — Semi-produits en polytétrafluoroéthylène (PTFE) —
Partie 1: Spécifications et désignation
Reference number
ISO 13000-1:2005(E)
©
ISO 2005
---------------------- Page: 5 ----------------------
SIST EN ISO 13000-1:2006
ISO 13000-1:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringi
...