SIST ISO 14635-3:2006

Gears -- FZG test procedures -- Part 3: FZG test method A/2,8/50 for relative scuffing load-carrying capacity and wear characteristics of semifluid gear greases

Name：SIST ISO 14635-3:2006   Standard name：Gears -- FZG test procedures -- Part 3: FZG test method A/2,8/50 for relative scuffing load-carrying capacity and wear characteristics of semifluid gear greases Standard number：SIST ISO 14635-3:2006   language：English language Release Date：30-Jun-2006   technical committee：ISEL - Mechanical elements Drafting committee：   ICS number：21.200 - Gears

SLOVENSKI STANDARD
SIST ISO 14635-3:2006
01-julij-2006
=REQLNL3RWHNSUHVNXãDQMD)=*GHO0HWRGD)=*$]DXJRWDYOMDQMH
UHODWLYQHQRVLOQRVWLJOHGHQDUD]MHGDQMHLQ]DXJRWDYOMDQMHREUDEQLKODVWQRVWL
SROWHNRþLKPDVWL
Gears - FZG test procedures - Part 3: FZG test method A/2, 8/50 for relative scuffing
load-carrying capacity and wear characteristics of semifluid gear greases
Ta slovenski standard je istoveten z:
ICS:
21.200
SIST ISO 14635-3:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

INTERNATIONAL ISO
STANDARD 14635-3
First edition
2005-09-15

Gears — FZG test procedures —
Part 3:
FZG test method A/2,8/50 for relative
scuffing load-carrying capacity and wear
characteristics of semifluid gear greases
Engrenages — Méthodes d'essai FZG —
Partie 3: Méthode FZG A/2,8/50 pour évaluer la capacité de charge au
grippage et les caractéristiques d'usure des graisses d'engrenages
semi-fluides




Reference number
ISO 14635-3:2005(E)
©
ISO 2005

---------------------- Page: 2 ----------------------

ISO 14635-3:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 3 ----------------------

ISO 14635-3:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Brief description of method. 4
4.1 General. 4
4.2 Precision. 4
5 Test materials. 4
5.1 Test gears . 4
5.2 Cleaning fluid . 4
6 Apparatus . 6
6.1 FZG spur gear test rig . 6
6.2 Heating device. 7
6.3 Revolution counter .
...