|
SIST-TP ISO/TR 1281-1:2009
01-junij-2009
.RWDOQLOHåDML3RMDVQLORNVWDQGDUGX,62GHO,PHQVNDGLQDPLþQD
REUHPHQLWHYLQLPHQVNDGREDWUDMDQMD
Rolling bearings - Explanatory notes on ISO 281 - Part 1: Basic dynamic load rating and
basic rating life
Wälzlager - Erläuternde Anmerkungen zur ISO 281 - Teil 1: Dynamische Tragzahlen
und nominelle Lebensdauer
Roulements - Notes explicatives sur l'ISO 281 - Partie 1: Charges dynamiques de base
et durée nominale de base
Ta slovenski standard je istoveten z: ISO/TR 1281-1:2008
ICS:
21.100.20 Kotalni ležaji Rolling bearings
SIST-TP ISO/TR 1281-1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TP ISO/TR 1281-1:2009
---------------------- Page: 2 ----------------------
SIST-TP ISO/TR 1281-1:2009
TECHNICAL ISO/TR
REPORT 1281-1
First edition
2008-12-01
Rolling bearings — Explanatory notes
on ISO 281 —
Part 1:
Basic dynamic load rating and basic
rating life
Roulements — Notes explicatives sur l'ISO 281 —
Partie 1: Charges dynamiques de base et durée nominale de base
Reference number
ISO/TR 1281-1:2008(E)
©
ISO 2008
---------------------- Page: 3 ----------------------
SIST-TP ISO/TR 1281-1:2009
ISO/TR 1281-1:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2008
or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
---------------------- Page: 4 ----------------------
SIST-TP ISO/TR 1281-1:2009
ISO/TR 1281-1:2008(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Symbols . 1
4 Basic dynamic load rating . 3
4.1 Basic dynamic radial load rating, C , for radial ball bearings . 4
r
4.2 Basic dynamic axial load rating, C , for single row thrust ball bearings. 7
a
4.3 Basic dynamic axial load rating, C , for thrust ball bearings with two or more rows of
a
balls. 9
4.4 Basic dynamic radial load rating, C , for radial roller bearings. 10
r
4.5 Basic dynamic axial load rating, C , for single row thrust roller bearings. 12
a
4.6 Basic dynamic axial load rating, C , for thrust roller bearings with two or more rows of
a
rollers . 13
5 Dynamic equivalent load.
...