SIST ISO 199:2015

Rolling bearings - Thrust bearings - Geometrical product specification (GPS) and tolerance values

SIST ISO 199:2015

Name:SIST ISO 199:2015   Standard name:Rolling bearings - Thrust bearings - Geometrical product specification (GPS) and tolerance values
Standard number:SIST ISO 199:2015   language:English language
Release Date:04-Mar-2015   technical committee:ISEL - Mechanical elements
Drafting committee:   ICS number:21.100.20 - Rolling bearings
SLOVENSKI STANDARD
SIST ISO 199:2015
01-april-2015
1DGRPHãþD
SIST ISO 199:2006
.RWDOQLOHåDML±$NVLDOQLOHåDML6SHFLILNDFLMHJHRPHWULMVNLKYHOLþLQL]GHOND *36 LQ
YUHGQRVWLWROHUDQFH
Rolling bearings - Thrust bearings - Geometrical product specification (GPS) and
tolerance values
Roulements - Butées - Spécification géométrique des produits (GPS) et valeurs de
tolérance
Ta slovenski standard je istoveten z: ISO 199:2014
ICS:
21.100.20 Kotalni ležaji Rolling bearings
SIST ISO 199:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 199:2015

---------------------- Page: 2 ----------------------

SIST ISO 199:2015
INTERNATIONAL ISO
STANDARD 199
Fourth edition
2014-07-15
Rolling bearings — Thrust bearings
— Geometrical product specification
(GPS) and tolerance values
Roulements — Butées — Spécification géométrique des produits
(GPS) et valeurs de tolérance
Reference number
ISO 199:2014(E)
©
ISO 2014

---------------------- Page: 3 ----------------------

SIST ISO 199:2015
ISO 199:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 199:2015
ISO 199:2014(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 1
5 Limit deviations and tolerance values . 7
5.1 General . 7
5.2 Tolerance class Normal . 8
5.3 Tolerance class 6 .10
5.4 Tolerance class 5 .12
5.5 Tolerance class 4 .14
Annex A (informative) Symbols and terms as given in ISO 199:2005 in relationship to new
descriptions given in this document .16
Annex B (informative) Example of drawing indications of characteristics with specification for
thrust bearings .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27