SIST ISO 3245:2016

Rolling bearings - Needle roller bearings with drawn cup and without inner ring - Boundary dimensions, geometrical product specifications (GPS) and tolerance values

SIST ISO 3245:2016

Name:SIST ISO 3245:2016   Standard name:Rolling bearings - Needle roller bearings with drawn cup and without inner ring - Boundary dimensions, geometrical product specifications (GPS) and tolerance values
Standard number:SIST ISO 3245:2016   language:English language
Release Date:21-Mar-2016   technical committee:ISEL - Mechanical elements
Drafting committee:   ICS number:21.100.20 - Rolling bearings
SLOVENSKI STANDARD
SIST ISO 3245:2016
01-maj-2016
1DGRPHãþD
SIST ISO 3245:2008
.RWDOQLOHåDML7XOMþQLLJOLþQLOHåDMLEUH]QRWUDQMHJDREURþD5REQHPHUH
VSHFLILNDFLMHJHRPHWULMVNLKYHOLþLQL]GHOND *36 LQYUHGQRVWLWROHUDQFH
Rolling bearings - Needle roller bearings with drawn cup and without inner ring -
Boundary dimensions, geometrical product specifications (GPS) and tolerance values
Roulements - Douilles à aiguilles sans bague intérieure - Dimensions d'encombrement,
spécification géométrique des produits (GPS) et valeurs de tolérance
Ta slovenski standard je istoveten z: ISO 3245:2015
ICS:
21.100.20 Kotalni ležaji Rolling bearings
SIST ISO 3245:2016 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 3245:2016

---------------------- Page: 2 ----------------------

SIST ISO 3245:2016
INTERNATIONAL ISO
STANDARD 3245
Fourth edition
2015-12-01
Rolling bearings — Needle roller
bearings with drawn cup and without
inner ring — Boundary dimensions,
geometrical product specifications
(GPS) and tolerance values
Roulements — Douilles à aiguilles sans bague intérieure —
Dimensions d’encombrement, spécification géométrique des produits
(GPS) et valeurs de tolérance
Reference number
ISO 3245:2015(E)
©
ISO 2015

---------------------- Page: 3 ----------------------

SIST ISO 3245:2016
ISO 3245:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
[email protected]
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 3245:2016
ISO 3245:2015(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 1
5 Nominal boundary dimensions . 4
6 Tolerances . 5
6.1 General . 5
6.2 Tolerance for the bore diameter . 5
6.3 Tolerance for the drawn cup . 7
6.3.1 Drawn cup width, C. 7
6.3.2 End thickness of profiled end and flat end drawn cup C and C .
1 2 8
6.3.3 Chamfer dimension, r .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27