SIST ISO 3547-2:2020

Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diameters

SIST ISO 3547-2:2020

Name:SIST ISO 3547-2:2020   Standard name:Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diameters
Standard number:SIST ISO 3547-2:2020   language:English language
Release Date:19-Jul-2020   technical committee:ISEL - Mechanical elements
Drafting committee:   ICS number:21.100.10 - Plain bearings
SLOVENSKI STANDARD
SIST ISO 3547-2:2020
01-oktober-2020
Drsni ležaji - Zvite puše - 2. del: Podatki za preskus zunanjega in notranjega
premera
Plain bearings - Wrapped bushes - Part 2: Test data for outside and inside diameters
Paliers lisses - Bagues roulées
Ta slovenski standard je istoveten z: ISO 3547-2:2017
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 3547-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 3547-2:2020

---------------------- Page: 2 ----------------------
SIST ISO 3547-2:2020
INTERNATIONAL ISO
STANDARD 3547-2
Third edition
2017-02
Plain bearings — Wrapped bushes —
Part 2:
Test data for outside and inside
diameters
Paliers lisses — Bagues roulées —
Partie 2: Données d’essai pour le diamètre extérieur et le diamètre
intérieur
Reference number
ISO 3547-2:2017(E)
©
ISO 2017

---------------------- Page: 3 ----------------------
SIST ISO 3547-2:2020
ISO 3547-2:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
[email protected]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 3547-2:2020
ISO 3547-2:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units . 2
5 Presentation of data on drawing. 2
6 Tests . 4
6.1 Test A . 4
6.2 Test B . 4
6.3 Test C . 4
6.4 Test D . 4
7 Test A . 4
7.1 Description . 4
7.2 Calculation basis . 4
7.2.1 Elastic reduction, v, of outside diameter, D .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27