|
INTERNATIONAL ISO/ASTM
DRAFT
STANDARD FDIS
52945
ISO/TC 261
Additive manufacturing for
Secretariat: DIN
automotive — Qualification principles
Voting begins on:
2023-09-25 — Generic machine evaluation and
specification of key performance
Voting terminates on:
2023-11-20
indicators for PBF-LB/M processes
Fabrication additive pour l'automobile — Principes de qualification
— Évaluation générique de la machine et spécifications des
indicateurs clefs de performance pour les procédés PBF-LB/M
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/ASTM FDIS 52945:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO/ASTM International 2023
---------------------- Page: 1 ----------------------
ISO/ASTM FDIS 52945:2023(E)
FINAL
INTERNATIONAL ISO/ASTM
DRAFT
STANDARD FDIS
52945
ISO/TC 261
Additive manufacturing for
Secretariat: DIN
automotive — Qualification principles
Voting begins on:
— Generic machine evaluation and
specification of key performance
Voting terminates on:
indicators for PBF-LB/M processes
Fabrication additive pour l'automobile — Principes de qualification
— Évaluation générique de la machine et spécifications des
indicateurs clefs de performance pour les procédés PBF-LB/M
COPYRIGHT PROTECTED DOCUMENT
© ISO/ASTM International 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
ISO copyright office ASTM International
RECIPIENTS OF THIS DRAFT ARE INVITED TO
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
Phone: +41 22 749 01 11 Phone: +610 832 9634
DOCUMENTATION.
Fax: +610 832 9635
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: [email protected] Email: [email protected]
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/ASTM FDIS 52945:2023(E)
Website: www.iso.org Website: www.astm.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
© ISO/ASTM International 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO/ASTM International 2023
---------------------- Page: 2 ----------------------
ISO/ASTM FDIS 52945:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Methodology for generic machine evaluation . 2
4.1 Specification of use-cases . 2
4.1.1 General .
...