ISO/IEC 18013-4:2019/Amd 1:2024

Personal identification — ISO-compliant driving licence — Part 4: Test methods — Amendment 1: Test methods for compact encoding

ISO/IEC 18013-4:2019/Amd 1:2024

Name:ISO/IEC 18013-4:2019/Amd 1:2024   Standard name:Personal identification — ISO-compliant driving licence — Part 4: Test methods — Amendment 1: Test methods for compact encoding
Standard number:ISO/IEC 18013-4:2019/Amd 1:2024   language:English language
Release Date:11-Jan-2024   technical committee:ISO/IEC JTC 1/SC 17 - Cards and security devices for personal identification
Drafting committee:ISO/IEC JTC 1/SC 17 - Cards and security devices for personal identification   ICS number:35.240.15 - Identification cards. Chip cards. Biometrics
INTERNATIONAL ISO/IEC
STANDARD 18013-4
Second edition
2019-11
AMENDMENT 1
Personal identification —
ISO-compliant driving licence —
Part 4:
Test methods
AMENDMENT 1: Test methods for
compact encoding
PROOF/ÉPREUVE
Reference number
ISO/IEC 18013-4/Amd. 1:2023(E)
© ISO/IEC 2023

---------------------- Page: 1 ----------------------
ISO/IEC 18013-4/Amd. 1:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
PROOF/ÉPREUVE © ISO/IEC 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 18013-4/Amd. 1:2023(E)
Personal identification — ISO-compliant driving licence —
Part 4:
Test methods
AMENDMENT 1: Test methods for compact encoding

Clause 2 Normative references
Add the date of publication to the reference to ISO/IEC 18013-2 as follows:
ISO/IEC 18013-2:2020
Replace all the occurrences of ISO/IEC 18013-2 in the document to the dated version.

Clause 4
Add the following abbreviated term after CA
CE compact encoding

Subclause 6.2.2.1
Replace
"One IUT is defined as an IDL with SE for SIC (see ISO/IEC 18013-2:—, Annex C)"
by
"One IUT is defined as an IDL with SE for SIC (see ISO/IEC 18013-2:2020, Annex C) or an IDL with CE
(see ISO/IEC 18013-2:2020, Annex B) "

Subclause 6.3.1.3
Replace the full text by
"All equipment described in Annexes A to D pertinent to the machine-readable technology supported by
the IUT shall be available."

Subclause 7.1
Replace the second sentence by
"Test requirements for Commands and LDS tests conformity are defined in Annexes A to D."

1
© ISO/IEC 2023 – All rights reserved PROOF/ÉPREUVE

---------------------- Page: 3 ----------------------
ISO/IEC 18013-4/Amd. 1:2023(E)
Subclause 7.3
Add the following subclause:
"7.3.3 Compact encoding (CE)
Test case specifications for CE cover are as follows:
— Data structure tests for CE and commands tests (applicable to CE on SIC). The tests shall be carried
out as specified in Annex D."

Subclause A.3.2.19
In row "References", replace
"ISO/IEC 18013-2:—, A.5.1"
by "ISO/IEC 18013-2: 2020, A.4.1".

Subclause A.3.2.20
In row "References", replace
ISO/IEC 18013-2:—, A.5.1
by
ISO/IEC 18013-2: 2020, A.4.1

Subclause A.3.2.21
In row "References", replace " ISO/IEC 18013-2:—, A.5.1"
by
"ISO/IEC 18013-2: 2020, A.4.1

Add following new Annex D after Annex C.
2
PROOF/ÉPREUVE © ISO/IEC 2023 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/IEC 18013-4/Amd. 1:2023(E)
Annex D
(normative)

Test case specification for Compact Encoding (CE)
D.1 General
This annex specifies the test cases for CE.
D.2 General test requirements
D.2.1 Preconditions for testing
The tests in this annex require a fully personalized IDL. This means that all mandatory data groups
shall be present. This annex tests all mandatory and optional data groups.
All tests are mandatory unless marked as optional or conditional.
D.2.2 Test setup
For setting up these tests, any read device able to read all data at the same time can be used.
D.2.3 Implementation conformance statement
In order to set up the tests properly, Tables D.1 and D.2 shall be completed.
The ISO/IEC 18013-2 and ISO/IEC 18013-3 specifications define several optional elements that an IDL
can support.
Since these elements are optional, it is not possible to define the corresponding tests as mandatory for
each IDL. Therefore, this document specifies a set of profiles. Each profile covers a specific optional
element. A tested IDL shall be assigned to the supported profiles in the ICS, and a test shall only be
performed if the IDL supports this profile.
Table D.1 — Implementation conformance statement
Applicable
Profile Information for test setup
(YES or NO)
SIC Contact ICC or PICC storage media
BAP Basic Access Protection
PACE Password Authenticated Connection Establishment
NO-SIC All technologies excluding ICs
DG2 IDL contains Data Group 2
DG3 IDL contains Data Group 3
DG4 IDL contains Data Group 4
DG7 IDL contains Data Group 7
DG11 IDL contains Data Group 11
SOD IDL contains SOD
SOD2 IDL contains DG.SOD.2, but no DG.SOD.3
SOD23 IDL contains DG.SOD.2 and DG.SOD.3
3
© ISO/IEC 2023 – All rights reserved PROOF/ÉPREUVE

---------------------- Page: 5 ----------------------
ISO/IEC 18013-4/Amd. 1:2023(E)
TTaabblle De D.1 1 ((ccoonnttiinnueuedd))
Applicable
Profile Information for test setup
(YES or NO)
NMA ID
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27