|
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 16422-5
ISO/TC 138/SC 2
Pipes and joints made of oriented
Secretariat: SNV
unplasticized poly(vinyl chloride)
Voting begins on:
2023-10-18 (PVC-O) for the conveyance of water
under pressure —
Voting terminates on:
2023-12-13
Part 5:
Fitness for purpose of the system
Tubes et assemblages en poly(chlorure de vinyle) non plastifié orienté
(PVC-O) pour le transport de l'eau sous pression —
Partie 5: Aptitude à l'emploi du système
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 16422-5:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 1 ----------------------
ISO/FDIS 16422-5:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 16422-5
ISO/TC 138/SC 2
Pipes and joints made of oriented
Secretariat: SNV
unplasticized poly(vinyl chloride)
Voting begins on:
(PVC-O) for the conveyance of water
under pressure —
Voting terminates on:
Part 5:
Fitness for purpose of the system
Tubes et assemblages en poly(chlorure de vinyle) non plastifié orienté
(PVC-O) pour le transport de l'eau sous pression —
Partie 5: Aptitude à l'emploi du système
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: +41 22 749 01 11
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: [email protected]
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 16422-5:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
© ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 2 ----------------------
ISO/FDIS 16422-5:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Fitness for purpose of joints and the system . 2
4.1 General . 2
4.2 Assemblies with non-end-load-bearing joints . 2
4.3 Assemblies with end-load-bearing joints . 3
5 Test methods . 4
5.1 Short-term test for leaktightnes
...