ISO 23814:2024

Cranes — Competency requirements for crane inspectors

ISO 23814:2024

Name:ISO 23814:2024   Standard name:Cranes — Competency requirements for crane inspectors
Standard number:ISO 23814:2024   language:English language
Release Date:30-Jun-2024   technical committee:ISO/TC 96/SC 5 - Use, operation and maintenance
Drafting committee:ISO/TC 96/SC 5 - Use, operation and maintenance   ICS number:03.100.30 - Management of human resources

International
Standard
ISO 23814
Second edition
Cranes — Competency
2024-07
requirements for crane inspectors
Appareils de levage à charge suspendue — Exigences relatives
aux compétences pour les inspecteurs d'appareils de levage à
charge suspendue
Reference number
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 1
4.1 Independence, impartiality and integrity .1
4.2 Technical knowledge .1
4.3 Experience requirements .2
4.4 Techniques for crane inspection . .3
Annex A (informative) Recommended crane inspector categories . 4
Annex B (informative) Performance criteria for technical knowledge . 5
Bibliography . 9

iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 96, Cranes, Subcommittee SC 5, Use, operation
and maintenance.
This second edition cancels and replaces the first edition (ISO 23814:2009), which has been technically
revised.
The main changes are as follows:
— in 4.2, technical knowledge to be possessed by crane inspectors has been revised;
— Clause 5 has been removed.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
Introduction
The objective of this document is to achieve uniform competency standards for work involving crane
inspectors.
In some countries, additional requirements for the competency of crane inspectors can apply.

v
International Standard ISO 23814:2024(en)
Cranes — Competency requirements for crane inspectors
1 Scope
This document specifies the competency required for persons who carry out periodic, exceptional, and
enhanced periodic inspections of cranes. It excludes the inspection and checks performed by crane operators
and maintenance personnel.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 4306-1, Cranes — Vocabulary — Part 1: General
ISO 4310, Cranes — Test code and procedures
ISO 9927 (all parts), Cranes — Inspections
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4306-1, ISO 4310 and the
follo
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27