ISO 29461-3:2024

Air intake filter systems for rotary machinery — Test methods — Part 3: Mechanical integrity of filter elements

ISO 29461-3:2024

Name:ISO 29461-3:2024   Standard name:Air intake filter systems for rotary machinery — Test methods — Part 3: Mechanical integrity of filter elements
Standard number:ISO 29461-3:2024   language:English language
Release Date:02-Jul-2024   technical committee:ISO/TC 142 - Cleaning equipment for air and other gases
Drafting committee:ISO/TC 142/WG 9 - Particulate air filter intake systems for rotary machinery and stationary internal combustion engines   ICS number:29.160.99 - Other standards related to rotating machinery

International
Standard
ISO 29461-3
First edition
Air intake filter systems for rotary
2024-07
machinery — Test methods —
Part 3:
Mechanical integrity of filter
elements
Systèmes de filtration d'air d'admission pour machines
tournantes — Méthodes d'essai —
Partie 3: Intégrité mécanique des éléments filtrants
Reference number
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 Test parameter .2
3.2 Filter to be tested .2
3.3 Test duration .3
3.4 Test materials .3
4 Test rig, conditions and equipment . 3
4.1 Test conditions .3
4.2 Test rig – General requirements .3
4.3 Camera .4
4.4 Differential pressure measurement .4
4.5 Flow measurement .4
4.6 Dust feeder .5
4.7 Water spraying nozzles (fogging nozzles) . .5
4.8 Final filter/coarse filter mat or grid .6
4.9 Temperature, relative humidity .6
5 Qualification of test rig and apparatus . 6
5.1 Pressure system test .6
5.2 Test rig — Pressure drop of test duct with no test device installed .6
5.3 Test rig — Pressure drop reference test .6
5.4 Summary of qualification requirements and schedule .6
6 Test materials . 7
6.1 Test dust .7
6.2 Water .7
6.3 Coarse filter .7
7 Test procedure . 7
7.1 General .7
7.2 Test result evaluation .8
7.2.1 General .8
7.2.2 Measurement of pressure drop .8
7.2.3 Visual inspection of filter .8
7.2.4 Visual inspection downstream of the test device .8
7.2.5 Final test in accordance with ISO 29461-1 .8
7.3 Test preparation .9
7.4 Determination of the initial loading concentration of test dust and water.9
7.5 Loading procedure .10
7.6 Fail/pass criteria .11
7.6.1 General .11
7.6.2 Release of parts .11
7.6.3 Pressure drop decrease .11
7.6.4 Visual inspection during test .11
7.6.5 Final test in accordance with ISO 29461-1 .11
8 Reporting results .12
8.1 General and descriptive information . 12
8.2 Test data and results . 13
8.3 Concluding statement .14
Annex A (normative) Wet burst testing.15
Annex B (informative) Test report example .16

iii
Bibliography .20

iv
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 142, Cleaning equipment for air and other gases,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC 195,
Cleaning equipment for air and other gases, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
A list of all parts in the ISO 29461 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

v
Introduction
In rotating machinery applications, the filtering system, typically a set of
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27