|
International
Standard
ISO 10256-2
Second edition
Protective equipment for use in ice
2024-07
hockey —
Part 2:
Head protectors for skaters
Équipements de protection destinés à être utilisés en hockey
sur glace —
Partie 2: Protections de tête pour les patineurs
Reference number
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 2
4.1 Ergonomics .2
4.2 Innocuousness .3
4.2.1 Materials .3
4.2.2 Design .3
4.3 Markings and information .3
4.4 Protected area .3
4.4.1 General .3
4.4.2 Ear aperture .3
4.4.3 Ventilation .3
4.5 Penetration (test blade) .3
4.6 Field of vision .3
4.7 Shock absorbing capacity .4
4.8 Retention system .4
4.8.1 Straps .4
4.8.2 Extensibility and strength .4
5 Test methods . 4
5.1 General .4
5.1.1 Tolerances .4
5.1.2 Sampling .4
5.1.3 Conditioning temperatures.4
5.1.4 Placing and adjusting head protectors .5
5.2 Ergonomics .5
5.3 Innocuousness .5
5.3.1 Materials .5
5.3.2 Design .5
5.4 Markings and information .5
5.5 Protected area .5
5.5.1 Test apparatus .5
5.5.2 Procedure .5
5.6 Penetration .5
5.6.1 Test apparatus .5
5.6.2 Procedure .6
5.7 Field of vision .6
5.8 Shock absorbing.6
5.8.1 Impact sites .6
5.8.2 Marking non- prescribed impact sites on headform .6
5.8.3 Apparatus .7
5.8.4 Impact procedure .7
5.9 Retention system function .7
5.9.1 Apparatus .7
5.9.2 Placing and adjusting .8
5.9.3 Extensibility and releasing force .8
6 Test report . 8
7 Markings . 8
8 Information for users . 8
iii
Annex A (normative) Impact test using a guided fall.16
iv
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 83, Sports and other recreational facilities
and equipment, Subcommittee SC 5, Ice hockey equipment and facilities, in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 158, Head protection, in accordance
with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 10256-2:2016), which has bee
...