ISO/R 274:1962

Title missing - Legacy paper document

ISO/R 274:1962

Name:ISO/R 274:1962   Standard name:Title missing - Legacy paper document
Standard number:ISO/R 274:1962   language:English language
Release Date:31-Dec-1961   technical committee:ISO/TMBG - Technical Management Board - groups
Drafting committee:ISO/TMBG - Technical Management Board - groups   ICS number:
UDC 621.643
Ref. No.: ISOlR 274 - 1962 (E)
IS0
I NTER N AT1 ON A L O RG AN I Z AT1 O N F O R STAN DA RD IZ AT I O N
IS0 RECOMMENDATION
R 274
COPPER TUBES OF CIRCULAR SECTION
DIMENSIONS: METRIC SERIES
1st EDITION
September 1962
COPYRIGHT RESERVED
The copyright of IS0 Recommendations and IS0 Standards
belongs to IS0 Member Bodies. Reproduction of these
documents, in any country, may be authorized therefore only
by the national standards organization of that country, being
a member of ISO.
For each individual country the only valid standard is the national standard of that country.
Printed in Switzerland
Also issued in French and Russian. Copies to be obtained through the national standards organizations.

---------------------- Page: 1 ----------------------
BRIEF HISTORY
The IS0 Recommendation R 274, Copper Tubes of Circular Section - Dimensions: Metric
Series, was drawn up by Technical Committee ISOjTC 5, Pipes and Fittings, the Secretariat of
which is held by the Association Suisse de Normalisation (SNV).
Work on this question by the Technical Committee began in 1952 and led, in 1960, to the
adoption of a Draft IS0 Recommendation.
In December 1960, this Draft IS0 Recommendation (No. 420) was circulated to all the
IS0 Member Bodies for enquiry. It was approved, subject to a few modifications of an editorial
nature, by the following Member Bodies :
Australia Greece Poland
Belgium Hungary Portugal
Brazil India Romania
Chile Iran Spain
Israël Sweden
Colombia
Czechoslovakia Italy Switzerland
Denmark Japan Turkey
Finland Netherlands United Kingdom
France Norway Yugoslavia
Germany
Three Member Bodies opposed the approval of the Draft:
Argentina, New Zealand, U.S.S.R.
The Draft IS0 Recommendation was then submitted by correspondence to the IS0 Council,
which decided, in September 1962, to accept it as an IS0 RECOMMENDATION.
-2-

---------------------- Page: 2 ----------------------
ISO/R 274 - 1962 (E)
IS0 Recommendation R 274 September 1962
COPPER TUBES OF CIRCULAR SECTION
DIMENSIONS: METRIC SERIES
1. DIMENSIONS
The dimensions which follow are applicable to all copper tubes of circular section, whatever their
method of manufacture and their condition of delivery.
i,1 Definitions
The outside dianieter of a tube is the arithmetic mean of any two mutually perpendicular
outside diameters in the same right section.
The thickness of a tube is the arithmetic mean of the two thicknesses traversed by the same
di ameter.
1.2 Dimensions
Dimensions in millimetres
Outside diameter
chosen from approxima
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27