ISO/R 826:1968

Mechanical property limits for rolled products of aluminium and aluminium alloys

ISO/R 826:1968

Name:ISO/R 826:1968   Standard name:Mechanical property limits for rolled products of aluminium and aluminium alloys
Standard number:ISO/R 826:1968   language:English language
Release Date:30-Nov-1968   technical committee:ISO/TC 79/SC 6 - Wrought aluminium and aluminium alloys
Drafting committee:ISO/TC 79/SC 6 - Wrought aluminium and aluminium alloys   ICS number:77.150.10 - Aluminium products
E
Ref. No. : ISO/R 826-1968 (E)
UDC 669.71-122 : 539.3/.4
IS0
I N T ER N AT I O N A L ORGAN 1 Z AT 1 ON FOR S TA N DARD 1 ZATl O N
IS0 RECOMMENDATION
.
R 826
MECHANICAL PROPERTY LIMITS
FOR ROLLED PRODUCTS OF ALUMINIUM
AND ALUMINIUM ALLOYS
1st EDITION
September 1968
COPYRIGHT RESERVED
The copyright of IS0 Recommendations and IS0 Standards
belongs to IS0 Member Bodies. Reproduction of these
documents, in any country, may be authorized therefore only
by the national standards organization of that country, being
a member of ISO.
For each individual country the only valid standard is the national standard of that country.
printed in Switzerland
Also issued in French and Russian. Copies to be obtained through the national standards organizations.

---------------------- Page: 1 ----------------------
BRIEF HISTORY
The IS0 Recommendation R 826, Mechanical property limits for rolled products of aluminium
was drawn up by Technical Committee ISO/TC 79, Light metals and their
and aluminium alloys,
alloys, the Secretariat of which is held by the Association Française de Normalisation (AFNOR).
Work on this question by the Technical Committee began in 1959 and led, in 1965, to the
adoption of a Draft IS0 Recommendation.
In October 1966, this Draft IS0 Recommendation (No. 1116) was circulated to all the IS0
Member Bodies for enquiry. It was approved, subject to a few modifications of an editorial nature, by
the following Member Bodies :
Austria Ireland South Africa, Rep. of
Belgium Israel Turkey
Canada Italy U.A.R.
Chile Japan United Kingdom
Czechoslovakia Netherlands U.S.A.
France Norway U.S.S.R.
Hungary Sweden Yugoslavia
India Switzerland
No Member Body opposed the approval of the Draft.
The Draft IS0 Recommendation was then submitted by correspondence to the IS0 Council,
which decided, in September 1968, to accept it as an IS0 RECOMMENDATION.
-2-

---------------------- Page: 2 ----------------------
tSO/R 826-1968 (E
IS0 Recommendation R 826 September 1968
MECHANICAL PROPERTY LIMITS
FOR ROLLED PRODUCTS OF ALUMINIUM
AND ALUMINIUM ALLOYS
.
1. SCOPE
The grades or alloys listed in this IS0 Recommendation are those the designation and chemical
composition of which are specified in IS0 Recommendation R 209 -1968, Composition of wrought
products of aluminium and aluminium alloys.
Before comparing them with the limiting values listed in section 3, the measured or calculated values
of 0.2 proof stress or yield strength [ R,(0.2)], or of tensile strength (f?,,.,), should be rounded off
to the nearest 0.1 kgf/mm2 (or 100 lbf/in2) and those of the percentage elongation (A) to the
nearest 1 (see Annexes A and B).
For products up to 2.6 mm (0.102 in) thick, national standards may contain either elongation
requirements or bend test requirements, or both.
The values given for alloys AlCu4MgSi, Al-Cu4Mgl and Al-Cu4SiMg apply to the material delivered
by the supplier in the “solution treated and naturally aged” condition (or “solution treated and
precipitation treated” condition). If the user reheat-treats the material, these values may not be at-
tained.
L
2. SYMBOLS AND ABBREVIATIONS
The symbols and abbreviations used in section 3 have the following meanings :
R, (0.2) : 0.2 proof stress or yield strength
Rm : Tensile strength
A : Percentage elongation after rupture
: Original cross-sectional area of the gauge length of the test piece
so
1 kgf/mm2 : 1 kilogramme-force per square millimetre = about 9.8 N/mm2
(newton per square millimetre)
1 O00 lbf/in2 : 1000 pounds-force per square inch = about 6.9 N/mmz
-3-

---------------------- Page: 3 ----------------------
ISO/R 826-1968 (E)
uuu
a3 uuu
53
I
I
=e O00
O00
.5 h
N
mb mb
Nm
mm
~
000000
““O
bb
mmmmm
mmmmm
mm
99999
99
66636
oz
99999
99999
99999
wwwww Il
30000
36663
99999 99999
00000
3 *366,3
99999
99999
r-r-r-r-r-
00000
N
O2
O<
‘IlIl
IIIII
IlIII
Oh IlliI Il Il
-0
N
E
E
l1Il1 IlIll
IlIll
. IlIli Il
L b0
-0mm
-0mm
-0mm
mmob
mm0b mmob
991ci9 99 “!O
997q.9
0000-
0000-
0000-
v)
vvvvv/
O .5
3m-mo
ON-mO ON-mO
om-mo crmmom
mmmom
~mmom
mmmom
.99?ci
9997q 999?.
999-q
30000
00000 00000
O0000
U
22
E
m
~
O
a-
a
-
-4-
...I
...I

---------------------- Page: 4 ----------------------
ISOlR 826-1968 (E
uuu
ZZZI 1
I
ccc
O00
inmininin
99999
99999
00000
44444,
NCICICICI
.
99999
42z34,
99999 99999 99 99999
mmmmm
44z44
99999
IlIII IlIll
IIIII IlIl
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27