ISO/R 1019:1969

Title missing - Legacy paper document

ISO/R 1019:1969

Name:ISO/R 1019:1969   Standard name:Title missing - Legacy paper document
Standard number:ISO/R 1019:1969   language:English language
Release Date:31-Dec-1968   technical committee:ISO/TMBG - Technical Management Board - groups
Drafting committee:ISO/TMBG - Technical Management Board - groups   ICS number:
Ref. No. : ISO/R 1019-1969 (E)
UDC 778.533.4 : 771.531.352
IS0
I N T ER N AT I O N A L ORGAN IZ AT i O N FOR STAN DA RD IZATl O N
IS0 RECOMMENDATION
R 1019
CINEMATOGRAPHY
DIMENSIONS OF DAYLIGHT LOADING SPOOLS
FOR 16 mm MOTION-PICTURE FILM
1 st EDITION
March 1969
COPYRIGHT RESERVED
The copyright of IS0 Recommendations and IS0 Standards
belongs to IS0 Member Bodies. Reproduction of these
documents, in any country, may be authorized therefore only
by the national standards organization of that country, being
a member of ISO.
For each individual country the only valid standard is the national standard of that country.
Printed in Switzerland
Also issued in French and Russian. Copies to be obtained through the national standards organizations.

---------------------- Page: 1 ----------------------
BKlEF HISTORY
The IS0 Recommendation R 1019, Cinematography - - Dimensions ofdaylight loading spools for 16 mm
motion-picrure film, was drawn up by Technical Committee iSO/TC 36, Cinematography, the Secretariat of
which is held by the American National Standards Institute (ANSI).
Work on this question led to the adoption of a Draft IS0 Recommendation.
In November 1966, this Draft IS0 Recommendation (No. 1049) was circulated to all the IS0 Member Bodies
for enquiry. It was approved, subject to a few modifications of an editorial nature, by the following Member
Bodies :
Belgium Germany Netherlands
Brazil Greece Romania
Bulgaria
Hungary Sweden
Canada Israel Switzerland
Chile Italy U.A.R.
Czechoslovakia Japan United Kingdom
France Korea, Rep. of U.S.A.
No Member Body opposed the approval of the Draft.
The Draft IS0 Recommendation was then submitted by correspondence to the IS0 Council which decided.
in March 1969, to accept it as an IS0 RECOMMENDATION.

---------------------- Page: 2 ----------------------
-4-
ISO/R 1019-1969 (E)
I IS0 Recommendation R 1019 March 1969
CINEMATOGRAPHY
DIMENSIONS OF DAYLIGHT LOADING SPOOLS
FOR 16 rnm MOTION-PICTURE FILM
1. SCOPE
1.1 This IS0 Recommendation specifies the dimensions and characteristics of general purpose spools of
nominal capacities 15 m (50 feet), 30 m (100 feet), 60 m (200 feet), and 120 m (400 feet) for 16 mm
motion-picture film.
The dimensions specified are in substantial agreement with those given for microfilm camera supply
and take-up spools in IS0 Recommendation R . . .*, 35 mm and 16 mm microfilms, spools and reels.
(See Annex.)
1.2
Spools for some high-speed cameras should be carefully balanced and are not necessarily covered by
this IS0 Recommendation.
Flange view Section X - X Volume of
rotation diagram
I
FIGURE - Daylight loading spools for 16 mm motion-picture film
At present, at the stage of a draft proposal.
**
See clause 2.5 for explanation ofP.
***
See clause 2.7. This symbol signifies the runout of the cylindrical surface of the core with respect to the 2 axis in the manner
prescribed in IS0 Recommendation R 1101, Tolerances of form and of position - Part I : Generalities- symbols, indications
on drawings.

---------------------- Page: 3 ----------------------
-. 5 -
ISO/R 1019-1969 (
TABLE ~ Dimensions for daylight loading spools
for 16 mm motion-picture film
Dimension Nominal spool size millimeters inches I
+ 1.0
+ 0.04
A 15m 30m 60m 120m 7.6 0.30
B 15m 30m 60m 120m 3.1 + 0.4 0.12 +y
C(seeclause2.1) 15m 30m 60m 120m 8.05 + 0’” 0.317 +
15m 30m 60m 32.0 k0.5 1.26 k0.02
E
120 m 54.0 10.5 2.12 k0.02
120 m 38 min. 1.5 min.
O O
15 m
71s -1.0 2.81 - 0.04
O O
30 m 92.0
-1.0 3‘62 -0.04
M and Ml
O O
60 m
126.0 - 1.0 4‘96 -0.04
O O
120 m
169.0 - 1.0 6’65 -0.04
P(see clause 2.5) 15 m 30m 60 m
120 m 0.50 ma. 0.020 max.
S (see clause 2.7) 15 m 30 m 60 m 120 m 0.8 0.03
2. DIMENSIONS AND CHARACTERISTICS
2.1
The spindle and keyway holes shown in the Figure should be incorporated in both flanges* and should
be aligned. (Some laboratories use 35 mm rewind equipment for winding 16 mm film; often the
spindles on this equipment have long keys.) A second keyway, in the corner of the spindle hole
opposite the required keyway, is optional, but if used, should be incorporated in both flanges.
2.2
If rivet heads or other fastening devices extend beyond the outer surfaces of the flanges, they should
lie at a diameter larger than the minimum K diameter and should be within the boundaries defined by
oth
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27