ISO/R 1033:1969

Title missing - Legacy paper document

ISO/R 1033:1969

Name:ISO/R 1033:1969   Standard name:Title missing - Legacy paper document
Standard number:ISO/R 1033:1969   language:English language
Release Date:31-Dec-1968   technical committee:ISO/TMBG - Technical Management Board - groups
Drafting committee:ISO/TMBG - Technical Management Board - groups   ICS number:
Kef. No. : ISO/R 1033-1969 (E)
UDC 629.7.064.5 : 621.316.5
IS0
FO R STAN DARD IZATION
I N T ER NAT I ON A L O RG A N IZ AT1 O N
IS0 RECOMMENDATION
R 1033
DIMENSIONS FOR GENERAL PURPOSE PUSH-PULL
THR EE-POLE CI RCU IT-BR EAKERS FOR Al RCRAFT
1st EDITION
March 1969
COPYRIGHT RESERVED
The copyright of IS0 Recommendations and IS0 Standards
IS0 Member Bodies. Reproduction of these
belongs to
be authorized therefore only
documents, in any country, may
by the national standards organization of that country, being
a member of ISO.
For each individual country the only valid standard is the national standard of that country.
Printed in Switzerland
Also issued in French and Russian. Copies to be obtained through the national standards organizations.

---------------------- Page: 1 ----------------------
-2- ISO/R 1033-1969 (E)
I IS0 Recommendation R 1033 March 1969
I
I
DIMENSIONS FOR GENERAL PURPOSE PUSH-PULL
TH R E E-PO L E CI R C U I T-B R EA K E RS FOR A I R CR A FT
1. SCOPE
This IS0 Recommendation states the dimensions for general purpose push-pull three-pole circuit-breakers for
aircraft, of ratings up to and including 35 amperes.
NOTE. - Attention is drawn to the necessity for the national approving authority being satisfied that the rupturing capacity of
a particular circuit-breaker is adequate for the application in which it is proposed to be used.
2. DIMENSIONS OF CIRCUIT-BREAKERS
The dimensions of the circuit-breakers, and of the part projecting through the mounting panel, should be
2.1
as shown in Figure 1.
2.2 The circuit-breaker should have at the centre of the front face of the case a 12 mm diameter, 1 mm pitch, or
equivalent, male thread for fixing through the mounting panel.
.2.3 The holes in the panel for mounting the circuit-breaker should
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27