|
TECHNICAL SPECIFICATION
5G;
NR;
Physical layer measurements
(3GPP TS 38.215 version 15.2.0 Release 15)
---------------------- Page: 1 ----------------------
3GPP TS 38.215 version 15.2.0 Release 15 1 ETSI TS 138 215 V15.2.0 (2018-07)
Reference
DTS/TSGR-0138215vf20
Keywords
5G
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 38.215 version 15.2.0 Release 15 2 ETSI TS 138 215 V15.2.0 (2018-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 38.215 version 15.2.0 Release 15 3 ETSI TS 138 215 V15.2.0 (2018-07)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 4
1 Scope . 5
2 References . 5
3 Definitions, symbols and abbreviations . 5
3.1 Definitions . 5
3.2 Symbols . 5
3.3 Abbreviations . 5
4 Control of UE/NG-RAN measurements . 6
5 Measurement capabilities for NR . 6
5.1 UE measurement capabilities . 6
5.1.1 SS reference signal received power (SS-RSRP) . 7
5.1.2 CSI reference signal received power (CSI-RSRP) . 8
5.1.3 SS reference signal received quality (SS-RSRQ) . 9
5.1.4 CSI reference signal received quality (CSI-RSRQ) . 10
5.1.5 SS signal-to-noise and interference ratio (SS-SINR) . 10
5.1.6 CSI signal-to-noise and interference ratio (CSI-SINR) . 11
5.1.7 Void . 11
5.1.8 Void . 11
5.1.9 UE GNSS Timing of Cell Frames for UE positioning for E-UTRAN . 11
5.1.10 UE GNSS code measurements. 11
5.1.11 UE GNSS carrier phase measurements . 12
5.1.12 IEEE 802.11 WLAN RSSI . 12
5.1.13 Reference signal time difference (RSTD) for E-UTRAN . 12
5.1.14 SFN and frame timing difference (SFTD) . 12
5.1.15 E-UTRA RSRP . 13
5.1.16 E-UTRA RSRQ . 13
5.1.17 E-UTRA RS-SINR . 14
5.1.18 SS reference signal received power per branch (SS-RSRPB) . 14
5.2 NG-RAN measurement abilities . 14
5.2.1 SSS transmit power . 15
Annex A: Change history . 16
History . 17
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 38.215 version 15.2.0 Release 15 4 ETSI TS 138 215 V15.2.0 (2018-07)
Foreword
rd
This Technical Report has been produced by the 3 Generation Partnership Project (3GPP).
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z the third digit is incremented when editorial only changes have been incorporated in the document.
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 38.215 version 15.2.0 Release 15 5 ETSI TS 138 215 V15.2.0 (2018-07)
1 Scope
The present document describes the physical layer measurements for NR.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
[1] 3GPP TR 21.905: "Vocabulary for 3GPP Specifications"
[2] 3GPP TS 38.201: "NR; Physical Layer – General Description"
[3] 3GPP TS 38.211: "NR; Physical channels and modulation"
[4] 3GPP TS 38.212: "NR; Multiplexing and channel coding"
[5] 3GPP TS 38.213: "NR; Physical layer procedures for control channels"
[6] 3GPP TS 38.214: "NR; Physical layer procedures for data channels"
[7] 3GPP TS 38.321: "NR; Medium Access Control (MAC) protocol specification"
[8] 3GPP TS 38.331: "NR; Radio Resource Control (RRC); Protocol specification"
[9] 3GPP TS 38.104: "NR; Base Station (BS) radio transmission and reception"
[10] 3GPP TS 36.331: "Evolved Universal Terrestrial Radio Access (E-UTRA); Radio Resource
Control (RRC); Protocol specification"
[11] IEEE 802.11, Part 11: "Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY)
specifications, IEEE Std."
[12] 3GPP TS 38.133: "NR; Requirements for support of radio resource management"
[13] 3GPP TS 36.211: "Evolved Universal Terrestrial Radio Access (E-UTRA); Physical channels and
modulation"
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in TR 21.905 [1] and the following apply. A
term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905 [1].
3.2 Symbols
For the purposes of the present document, the following symbols apply:
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in TR 21.905 [1] and the following apply. An
abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in
TR 21.905 [1].
CSI-RSRP CSI Reference Signal Received Power
CSI-RSRQ CSI Reference Signal Received Quality
E-UTRAN Evolved UTRAN
GNSS Global Navigation Satellite System
GSM Global System for Mobile communication
SRS Sounding Reference Signal
ETSI
---------------------- Page: 6 ----------------------
3GPP TS 38.215 version 15.2.0 Release 15 6 ETSI TS 138 215 V15.2.0 (2018-07)
SS-RSRP Synchronization Signal Reference Signal Received Power
SS-RSRQ Synchronization Signal Reference Signal Received Quality
UTRAN Universal Terrestrial Radio Access Network
4 Control of UE/NG-RAN measurements
In this chapter the general measurement control concept of the higher layers is briefly described to provide an
understanding on how L1 measurements are initiated and controlled by higher layers.
With the measurement specifications L1 provides measurement capabilities for the UE and NG-RAN. These
measurements can be classified in different reported measurement types: intra-frequency, inter-frequency, inter-system,
traffic volume, quality and UE internal measurements.
In the L1 measurement definitions, see chapter 5, the measurements are categorised as measurements in the UE or
measurements in the NG-RAN.
5 Measurement capabilities for NR
In this chapter the physical layer measurements reported to higher layers are defined.
5.1 UE measurement capabilities
The structure of the table defining a UE measurement quantity is shown below.
Column field
Comment
Definition Contains the definition of the measurement.
Applicable for States in which state(s) it shall be possible to perform this measurement. The following terms are
used in the tables:
RRC_IDLE;
RRC_INACTIVE;
RRC_CONNECTED;
Intra-frequency appended to the RRC state:
Shall be possible to perform in the corresponding RRC state on an intra-frequency cell;
Inter-frequency appended to the RRC state:
Shall be possible to perform in the corresponding RRC state on an inter-frequency cell
Inter-RAT appended to the RRC state:
Shall be possible to perform in the corresponding RRC state on an inter-RAT cell.
ETSI
---------------------- Page: 7 ----------------------
3GPP TS 38.215 version 15.2.0 Release 15 7 ETSI TS 138 215 V15.2.0 (2018-07)
5.1.1 SS reference signal received power (SS-RSRP)
Definition SS reference signal received power (SS -RSRP) is defined as the linear average over the power
contributions (in [W]) of the resource elements that carry secondary synchronization signals
(SS). The measurement time resource(s) for SS-RSRP are confined within SS/PBCH Block
Measurement Time Configuration (SMTC) window duration. If SS-RSRP is used for L1-RSRP as
configured by reporting configurations as defined in 3GPP TS 38.214 [6], the measurement time
resources(s) restriction by SMTC window duration is not applicable.
For SS-RSRP determination demodulation reference signals for physical broadcast channel
(PBCH) and, if indicated by higher layers, CSI reference signals in addition to secondary
synchronization signals may be used. SS-RSRP using demodulation reference signal for PBCH
or CSI reference signal shall be measured by linear averaging over the power contributions of
the resource elements that carry corresponding reference signals taking into account power
scaling for the reference signals as defined in 3GPP TS 38.213 [5]. If SS-RSRP is not used for
L1-RSRP, the additional use of CSI reference signals for SS-RSRP determination is not
applicable.
SS-RSRP shall be measured only among the reference signals corresponding to SS/PBCH
blocks with the same SS/PBCH block index and the same physical-layer cell identity.
If SS-RSRP is not used for L1-RSRP and higher-layers indicate certain SS/PBCH blocks for
performing SS-RSRP measurements, then SS-RSRP is measured only from the indicated set of
SS/PBCH block(s).
For frequency range 1, the reference point for the SS-RSRP shall be the antenna connector of
the UE. For frequency range 2, SS-RSRP shall be measured based on the combined signal from
antenna elements corresponding to a given receiver branch. For frequency range 1 and 2, if
receiver diversity is in use by the UE, the reported SS-RSRP value shall not be lower than the
corresponding SS-RSRP of any of the individual receiver branches.
Applicable for If SS-RSRP is used for L1-RSRP,
RRC_CONNECTED intra-frequency.
Otherwise,
RRC_IDLE intra-frequency,
RRC_IDLE inter-frequency,
RRC_INACTIVE intra-frequency,
RRC_INACTIVE inter-frequency,
RRC_CONNECTED intra-frequency,
RRC_CONNECTED inter-frequency
NOTE 1: The number of resource elements within the measurement period that are used by the UE to determine
SS-RSRP is left up to the UE implementation with the limitation that corresponding measurement
accuracy requirements have to be fulfilled.
NOTE 2: The power per resource element is determined from the energy received during the useful part of the
symbol, excluding the CP.
ETSI
---------------------- Page: 8 ----------------------
3GPP TS 38.215 version 15.2.0 Release 15 8 ETSI TS 138 215 V15.2.0 (2018-07)
5.1.2 CSI reference signal received power (CSI-RSRP)
Definition CSI reference signal received power (CSI-RSRP), is defined as the linear average over the
power contributions (in [W]) of the resource elements that carry CSI reference signals configured
for RSRP measurements within the considered measurement frequency bandwidth in the
configured CSI-RS occasions.
For CSI-RSRP determination CSI reference signals transmitted on antenna port 3000 according
to 3GPP TS 38.211 [4] shall be used. If CSI-RSRP is used for L1-RSRP, CSI reference signals
transmitted on antenna ports 3000, 3001 can be used for CSI-RSRP determination.
For intra-frequency CSI-RSRP measurements, if the measurement gap is not configured, UE is
not expected to measure the CSI-RS resource(s) outside of the active downlink bandwidth part.
For frequency range 1, the reference point for the CSI-RSRP shall be the antenna connector of
the UE. For frequency range 2, CSI-RSRP shall be measured based on the combined signal
from antenna elements corresponding to a given receiver branch. For frequency range 1 and 2, if
receiver diversity is in use by the UE, the reported CSI-RSRP value shall not be lower than the
corresponding CSI-RSRP of any of the individual receiver branches.
Applicable for
If CSI-RSRP is used for L1-RSRP,
RRC_CONNECTED intra-frequency.
Otherwise,
RRC_CONNECTED intra-frequency,
RRC_CONNECTED inter-frequency
NOTE 1: The number of resource elements within the considered measurement frequency bandwidth and within the
measurement period that are used by the UE to determine CSI-RSRP is left up to the UE implementation
with the limitation that corresponding measurement accuracy requirements have to be fulfilled.
NOTE 2: The power per resource element is determined from the energy received during the useful part of the
symbol, excluding the CP.
ETSI
---------------------- Page: 9 ----------------------
3GPP TS 38.215 version 15.2.0 Release 15 9 ETSI TS 138 215 V15.2.0 (2018-07)
5.1.3 SS reference signal received quality (SS-RSRQ)
Definition Secondary synchronization signal reference signal received quality (SS-RSRQ) is defined as the
ratio of N×SS-RSRP / NR carrier RSSI, where N is the number of resource blocks in t
...