|
TECHNICAL SPECIFICATION
Digital cellular telecommunications system (Phase 2+) (GSM);
Universal Mobile Telecommunications System (UMTS);
LTE;
Services and service capabilities
(3GPP TS 22.105 version 15.0.0 Release 15)
---------------------- Page: 1 ----------------------
3GPP TS 22.105 version 15.0.0 Release 15 1 ETSI TS 122 105 V15.0.0 (2018-07)
Reference
RTS/TSGS-0122105vf00
Keywords
GSM,LTE,UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 22.105 version 15.0.0 Release 15 2 ETSI TS 122 105 V15.0.0 (2018-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 22.105 version 15.0.0 Release 15 3 ETSI TS 122 105 V15.0.0 (2018-07)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 8
4 Framework for the description of telecommunication services and applications. 8
4.1 General . 8
4.2 Basic telecommunication services . 9
4.2.1 Bearer services . 9
4.2.2 Teleservices . 10
4.3 Supplementary services . 10
4.4 Service Capabilities . 10
5 Bearer Services . 11
5.1 Definition of bearer services . 11
5.2 Description of bearer services . 11
5.2.1 Information transfer . 11
5.2.2 Information Quality . 12
5.3 Supported bit rates . 13
5.4 Range of QoS requirements. 14
5.5 Supported End User QoS . 14
5.6 Radio Interface optimisation . 16
5.7 Service Based QoS Control of IP based Services . 17
5.8 QoS control for IP bearer service . 17
5.9 Ability to effectively handle a variety of different types of IP traffic . 17
5.10 IP address support . 18
6 Teleservices . 18
6.1 Definition of teleservices . 18
6.2 Description of teleservices . 18
6.3 Support of teleservices . 18
6.4 Existing Teleservices supported by PLMN . 20
6.4.1 Speech . 20
6.4.2 Emergency Call . 20
6.4.3 Short Message Service - Point to Point (SMS-PP) . 20
6.4.4 Short Message Service - Cell Broadcast (SMS-CB) . 21
6.5 Internet Access . 21
7 Supplementary Services . 21
8 Service Capability features . 21
8.1 Framework service capability features . 22
8.2 Non-Framework service capability features . 22
9 Standardised Protocols and Capabilities . 23
9.1 Access protocols . 23
9.2 Execution Environment . 23
10 Access dependent services and features . 24
11 Certificates . 25
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 22.105 version 15.0.0 Release 15 4 ETSI TS 122 105 V15.0.0 (2018-07)
Annex A (informative): Examples of services built from service capabilities features . 26
Annex B (informative): Description and analysis of communication schemes . 27
B.1 Communication schemes . 27
B.2 QoS related performance requirements for example end user applications . 27
B.2.1 Performance requirements for conversational real-time . 27
B.2.2 Performance requirements for Interactive Services . 28
B.2.3 Performance requirements for streaming services . 29
B.2.4 Performance requirements for Background applications . 30
B.3 Adaptability and bearer service negotiation . 31
Annex C (informative) : Change history . 32
History . 34
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 22.105 version 15.0.0 Release 15 5 ETSI TS 122 105 V15.0.0 (2018-07)
Foreword
This Technical Specification has been produced by the 3GPP.
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of this TS, it will be re-released by the TSG with an identifying
change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z the third digit is incremented when editorial only changes have been incorporated in the specification.
ETSI
---------------------- Page: 6 ----------------------
3GPP TS 22.105 version 15.0.0 Release 15 6 ETSI TS 122 105 V15.0.0 (2018-07)
1 Scope
Existing systems have largely standardised the complete sets of bearer services, teleservices and supplementary services
which they provide. 3GPP specifications specify service capabilities rather than services, allowing service
differentiation and system continuity. This Technical Specification (TS) describes how and what kind of services the
user has access to.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including
a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same
Release as the present document.
2.1 Normative references
[1] 3GPP TS 22.001: "Principles of circuit telecommunication services supported by a Public Land
Mobile Network (PLMN)".
[2] 3GPP TS 02.002: "Circuit Bearer services supported by a Public Land Mobile Network
(PLMN)".
[3] 3GPP TS 22.003: "Circuit Teleservices supported by a Public Land Mobile Network (PLMN)".
[4] 3GPP TS 22.004: "General on supplementary services".
[5] 3GPP TS 22.038: " SIM toolkit Stage 1".
[6] 3GPP TS 22.057: "Mobile Execution Environment (MExE); Service description; Stage 1".
[7] 3GPP TS 22.060: "General Packet Radio Service (GPRS) stage 1".
[8] 3GPP TS 22.078: "Customised Applications for Mobile network Enhanced Logic (CAMEL);
Service definition - Stage 1".
[9] 3GPP TS 22.101: "Service principles".
[10] Void
[11] 3GPP TS 22.135: "Multicall, stage 1".
[13] 3GPP TS 33.102: "3G Security, Security Architecture".
[14] 3GPP TS 23.107: "QoS Concept and Architecture; Stage 2".
[15] Open Mobile Alliance (OMA): OMA-RD-Parlay_Service_Access-V1_0-20100427-A
[16] 3GPP TS 22.340: "IP Multimedia System (IMS) messaging; Stage 1".
2.2 Informative references
[12] ITU-T Recommendation F.700 (11/2000): "Framework Recommendation for multimedia
services".
ETSI
---------------------- Page: 7 ----------------------
3GPP TS 22.105 version 15.0.0 Release 15 7 ETSI TS 122 105 V15.0.0 (2018-07)
[17] ITU-T Recommendation E.105 (08/1992): "International telephone service"
[18] ITU-T Recommendation E.800 (09/2008): "Definitions of terms related to quality of service"
[19] ITU-T Recommendation G.114 (05/2003): "One-way transmission time"
3 Definitions and abbreviations
3.1 Definitions
For the purposes of this TS, the following definitions apply:
Basic telecommunication service : this term is used as a common reference to both bearer services and teleservices.
Bearer service : is a type of telecommunication service that provides the capability of transmission of signals between
access points.
Call : a logical association between several users (this could be connection oriented or connection less).
Connection : is a communication channel between two or more end-points (e.g. terminal, server etc.).
Mobile termination : the mobile termination is the component of the user equipment which supports functions specific
to management of the radio interface (Um).
Multimedia service : Multimedia services are services that handle several types of media. For some services,
synchronisation between the media is necessary (e.g. synchronised audio and video). A multimedia service may involve
multiple parties, multiple connections, and the addition or deletion of resources and users within a single call.
Nomadic Operating Mode : Mode of operation where the terminal is transportable but being operated while stationary
and may in addition require user co-operation (e.g. close to open spaces, antenna setup.).
Quality of Service : the collective effect of service performances which determine the degree of satisfaction of a user
of a service. It is characterised by the combined aspects of performance factors applicable to all services, such as;
service operability performance;
- service accessibility performance;
- service retention performance;
- service integrity performance; and
- other factors specific to each service.
Service Capabilities: Bearers defined by parameters, and/or mechanisms needed to realise services. These are within
networks and under network control.
Service Capability Feature: Functionality offered by service capabilities that are accessible via the standardised
application interface
Services: Services are made up of different service capability features.
Supplementary service : is a service which modifies or supplements a basic telecommunication service. Consequently,
it cannot be offered to a user as a standalone service. It shall be offered together with or in association with a basic
telecommunication service. The same supplementary service may be common to a number of basic telecommunication
services.
Teleservice; is a type of telecommunication service that provides the complete capability, including terminal equipment
functions, for communication between users according to standardised protocols and transmission capabilities
established by agreement between operators.
ETSI
---------------------- Page: 8 ----------------------
3GPP TS 22.105 version 15.0.0 Release 15 8 ETSI TS 122 105 V15.0.0 (2018-07)
3.2 Abbreviations
For the purposes of this TS, the following abbreviations apply;
BER Bit Error Rate
CAMEL Customised Application for Mobile network Enhanced Logic
DTMF Dual Tone Multiple Frequency
TR Technical Report
TS Technical Specification
ETSI European Telecommunications Standards Institute
FAX Facsimile
FER Frame Erasure Rate
GSM Global System for Mobile Communications
GERAN GSM / EDGE Radio Access Network.
HE Home Environment
HSDPA High Speed Downlink Packet Access
IN Intelligent Network
ISDN Integrated Services Digital Network
ITU International Telecommunication Union
LCS Location Services
MExE Mobile Execution Environment
MMI Man Machine Interface
MO Mobile Origination
MT Mobile Termination
PC Personal Computer
PIN Personal Identity Number
PNP Private Numbering Plan
POTS Plain Old Telephony Service
QoS Quality of Service
USIM User Service Identity Module
SMS Short Message Service
SAT SIM Application Toolkit
SN Serving Network
SoLSA Support of Localised Service Area
UE User Equipment
4 Framework for the description of telecommunication
services and applications
4.1 General
Telecommunication services defined by 3GPP specifications are the communication capabilities made available to users
by home environment and serving network. A PLMN provides, in co-operation with other networks, a set of network
capabilities which are defined by standardised protocols and functions and enable telecommunication services to be
offered to users.
A service provision by a HE/SN to a user may cover the whole or only part of the means required to fully support the
service.
The service classification and description which follow are independent of different possible arrangements for the
ownership and provision to the user of the means required to support a service.
ETSI
---------------------- Page: 9 ----------------------
3GPP TS 22.105 version 15.0.0 Release 15 9 ETSI TS 122 105 V15.0.0 (2018-07)
4.2 Basic telecommunication services
Basic telecommunication services are divided in two broad categories;
- bearer services, which are telecommunication services providing the capability of transmission of signals
between access points;
- teleservices, which are telecommunication services providing the complete capability, including terminal
equipment functions, for communication between users according to protocols established by agreement
between network operators.
The communication link between the access points may consist of PLMN, one or more transit networks and a
terminating network. The networks between the two access points typically use different means for bearer control.
Figure 1 illustrates these definitions.
Teleservices
Bearer services
possible
Terminating
PLMN
TE TAF TE
MT
transit
network
network
UE
UE: User Equipment
MT: Mobile Termination
TE: Terminal Equipment
TAF: Teminal Adaption Function
NOTE 1: In order to limit the complexity of the figure, only one transit network is shown.
NOTE 2: The terminating network type may include a PLMN, either the originating one or another one.
NOTE 3: The bearer service terminates in the user equipment.
NOTE 4: The terminating network may be another network such as: PSTN, ISDN, IP networks/LANs and X.25
Figure 1: Basic telecommunication services supported by a PLMN
4.2.1 Bearer services
The characterisation of a bearer service is made by using a set of characteristics that distinguishes it from other bearer
services. Particular values are assigned to each characteristic when a given bearer service is described and defined.
The service characteristics as they apply at a given reference point where the user accesses the bearer service.
In the general case networks between the two access points use different control mechanisms. In this case the bearer
services of each network throughout the communication link have to be translated at the network interfaces to realize an
end to end bearer service.
A list of definitions of attributes and values used for bearer services is contained in clause 5.
The bearer services are negotiable and can be used flexibly by applications.
ETSI
---------------------- Page: 10 ----------------------
3GPP TS 22.105 version 15.0.0 Release 15 10 ETSI TS 122 105 V15.0.0 (2018-07)
4.2.2 Teleservices
Section 6 defines both standardised and non-standardised teleservices. Some teleservices are standardised because that
interworking with other systems have been recognised as a requirement. Other teleservices will not be standardised. A
decoupling between lower layer (i.e. bearer attributes) and higher layer capabilities will be necessary for the
development of teleservices.
4.3 Supplementary services
A supplementary service modifies or supplements a basic telecommunication service. Consequently, it cannot be
offered to a user as a stand alone service. It shall be offered together or in association with a basic telecommunication
service. The same supplementary service may be applicable to a number of basic telecommunication services.
Two methods are used for the characterisation of supplementary services;
- The first method is used for the description of existing standardised supplementary services. These services are
specified through the detailing of each of the operations involved in service provision and service usage (the
provision/withdrawal, registration/erasure, activation/deactivation, invocation and interrogation operations).
Clause 7 lists these services.
- The second method enables the provision of HE/SN specific supplementary services. To make this possible,
services can be built using service capability features which are accessed via the standardised application
interface.
A PLMN shall be able to handle multiple supplementary services within a call. Interactions shall be handled when
several supplementary services are activated in the same call. When multiple supplementary services can be activated
concurrently, some prioritisation of the services will be necessary. Certain services may override or deactivate other
services.
Interactions between operator specific supplementary services are not defined.
The following issues need consideration when interactions between services occur;
- Different phases of a call.
- A service spanning on more than one network.
- Service interactions that may occur between services offered to a single user, as well as between services offered
to different interacting users.
NOTE: The methods defined for characterisation of services are description methods. They do not imply or
restrict different implementations.
4.4 Service Capabilities
Service capabilities are based on functionality and mechanisms/toolkits such as provided by SAT [5], MExE [6], IN and
CAMEL [8]. These service capabilities can be made visible to the applications through an application interface. See
clause 8 for service capability features.
ETSI
---------------------- Page: 11 ----------------------
3GPP TS 22.105 version 15.0.0 Release 15 11 ETSI TS 122 105 V15.0.0 (2018-07)
5 Bearer Services
5.1 Definition of bearer services
Bearer services provide the capability for information transfer between access points and involve only low layer
functions. These functions are sometimes referred as low layer capabilities (in reference to OSI layers). The user may
choose any set of high layer protocols for his communication and the PLMN does not ascertain compatibility at these
layers between users.
In the general case a communication link between access points provides a general service for information transport.
The communication link may span over different networks such as Internet, Intranets, LANs and ATM based transit
networks, having network specific means for bearer control. Each network contributes to the end-to-end QoS perceived
by the end-user.
PS and CS domains provide a specific set of bearer capabilities. The Circuit bearer services are described in 22.002 [2].
The packet services (GPRS) is described in 3GPP TS 22.060 [7]. Following chapters describe the overall requirements
for both the CS and PS domain bearers and also for the bearers used by teleservices.
5.2 Description of bearer services
Bearer services are characterised by a set of end-to-end characteristics with requirements on QoS. The characteristics
and requirements shall cover major network scenarios, i.e. the cases when the terminating network is PSTN, ISDN, IP
networks/LANs, X.25 and a PLMN.
Quality of Service is the quality of a requested service (Teleservice or Bearer Service or any other service, e.g. customer
care) as perceived by the customer (ITU-T Recommendation E.800 [18]). QoS is always meant end-to-end. Network
P
...