|
TECHNICAL SPECIFICATION
Universal Mobile Telecommunications System (UMTS);
Electromagnetic compatibility (EMC)
requirements for mobile terminals and ancillary equipment
(3GPP TS 34.124 version 15.0.0 Release 15)
---------------------- Page: 1 ----------------------
3GPP TS 34.124 version 15.0.0 Release 15 1 ETSI TS 134 124 V15.0.0 (2018-07)
Reference
RTS/TSGR-0434124vf00
Keywords
UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 34.124 version 15.0.0 Release 15 2 ETSI TS 134 124 V15.0.0 (2018-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 34.124 version 15.0.0 Release 15 3 ETSI TS 134 124 V15.0.0 (2018-07)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 5
1 Scope . 6
2 References . 6
3 Definitions and abbreviations . 8
3.1 Definitions . 8
3.2 Abbreviations . 9
4 Test conditions . 10
4.1 General . 10
4.2 Arrangements for establishing a communication link . 10
4.3 Narrow band responses on receivers . 11
4.3.1 FDD and 3.84Mcps TDD option . 11
4.3.2 1,28Mcps TDD option . 11
4.3.3 7,68Mcps TDD option . 11
4.4 Receiver exclusion band . 12
5 Performance assessment . 13
5.1 General . 13
5.2 Equipment which can provide a continuous communication link . 13
5.3 Equipment which can only provide a discontinuous communication link (packet data/transmission). 13
5.4 Equipment which does not provide a communication link . 13
5.5 Conformance of ancillary equipment . 13
5.6 Equipment classification . 13
6 Performance criteria . 14
6.1 Performance criteria for continuous phenomena . 14
6.2 Performance criteria for Transient phenomena . 14
7 Applicability overview tables . 15
7.1 Emission . 15
7.2 Immunity . 16
8 Methods of measurement and limits for EMC emissions . 16
8.1 Test configurations . 16
8.2 Radiated Emission . 17
8.2.1 Definition . 17
8.2.2 Test method . 17
8.2.3 Limits . 17
8.2.3.1 FDD and 3.84 Mcps TDD option . 17
8.2.3.2 1,28 Mcps TDD option . 18
8.2.3.3 7,68 Mcps TDD option . 18
8.2.4 Interpretation of the measurement results . 19
8.3 Conducted emission DC power input/output port . 19
8.3.1 Definition . 19
8.3.2 Test method . 19
8.3.3 Limits . 20
8.4 Conducted emissions, AC mains power input/output port . 20
8.4.1 Definition . 20
8.4.2 Test method . 20
8.4.3 Limits . 20
8.5 Harmonic current emissions (AC mains input port) . 20
8.6 Voltage fluctuations and flicker (AC mains input port) . 21
9 Test methods and levels for immunity tests . 21
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 34.124 version 15.0.0 Release 15 4 ETSI TS 134 124 V15.0.0 (2018-07)
9.1 Test configurations . 21
9.2 RF electromagnetic field (80 MHz - 1000 MHz and 1400 MHZ to 2700 MHz). 21
9.2.1 Definition . 21
9.2.2 Test method and level . 22
9.2.3 Performance criteria . 22
9.3 Electrostatic discharge . 22
9.3.1 Definition . 22
9.3.2 Test method and level . 22
9.3.3 Performance criteria . 22
9.4 Fast transients common mode . 22
9.4.1 Definition . 23
9.4.2 Test method and level . 23
9.4.3 Performance criteria . 23
9.5 RF common mode (0.15 MHz to 80 MHz) . 23
9.5.1 Definition . 23
9.5.2 Test method and level . 23
9.5.3 Performance criteria . 24
9.6 Transients and surges, vehicular environment. 24
9.6.1 Definition . 24
9.6.2 Test method and level . 24
9.6.2.1 12 V DC powered equipment . 24
9.6.2.2 24 V DC powered equipment . 24
9.6.3 Performance criteria . 25
9.7 Voltage dips and interruptions . 25
9.7.1 Definition . 25
9.7.2 Test method and level . 25
9.7.3 Performance criteria . 25
9.8 Surges, common and differential mode . 25
9.8.1 Definition . 26
9.8.2 Test method and level . 26
9.8.3 Performance criteria . 26
Annex A (normative): Performance assessment voice call. Audio break through . 27
A.1 Calibration of audio levels . 27
A.2 Measurement of audio levels . 28
Annex B (normative): Performance assessment of data transfer call. Error Ratios . 29
B.1 Calibration of data transfer . 29
B.2 Derivation of Error Ratios . 29
B.3 EUT without data application ancillary . 29
B.4 EUT with data application ancillary . 30
Annex C (informative): Change History . 31
History . 32
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 34.124 version 15.0.0 Release 15 5 ETSI TS 134 124 V15.0.0 (2018-07)
Foreword
rd
This Technical Specification has been produced by the 3 Generation Partnership Project (3GPP).
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z the third digit is incremented when editorial only changes have been incorporated in the document.
ETSI
---------------------- Page: 6 ----------------------
3GPP TS 34.124 version 15.0.0 Release 15 6 ETSI TS 134 124 V15.0.0 (2018-07)
1 Scope
rd
The present document establishes the essential EMC requirements for "3 generation" digital cellular mobile terminal
equipment and ancillary accessories in combination with a 3GPP user equipment (UE).
The equipment conforming to the requirements laid out in the present document and used in its intended
electromagnetic environment in accordance with the manufacturers instructions
- shall not generate electromagnetic disturbances at a level .which may interfere with the intended operation of
other equipment;
- has an adequate level of intrinsic immunity to electromagnetic disturbances to operate as intended;
The present document specifies the applicable EMC tests, the methods of measurement, the frequency range, the limits
and the minimum performance criteria for all types of UTRA UE´s operating in FDD or TDD modes and their
accessories. The TDD has two options. The two options are the 3,84Mcps and 1,28Mcps options respectively. The
requirements are listed in different subsections only if the parameters deviate.Base station equipment operating within
network infrastructure is outside the scope of the present document. However, the present document does cover mobile
and portable equipment that is intended to be operated in a fixed location while connected to the AC mains. Base
stations in the radio access network are covered by the technical specification TS25.113 [1].
Requirements for the radiated emission from the enclosure port of integral antenna equipment and ancillaries have been
included. Technical specifications for conducted emissions from the antenna connector are found in the 3GPP
specifications for the radio interface, e.g. TS34.121 [2] and TS34.122 [3], for the effective use of the radio spectrum.
The immunity requirements have been selected to ensure an adequate level of compatibility for apparatus in residential,
commercial, light industrial and vehicular environments. The levels however, do not cover extreme cases, which may
occur in any location but with low probability of occurrence.
The environment classification used in the present document refers to the environment classification used in the Generic
Standards IEC 61000-6-1 [4], IEC 61000-6-3 [5], except the vehicular environment class which refers to
ISO 7637 Part 1 [6] and Part 2 [7].
Compliance of radio equipment to the requirements of the present document does not signify compliance to any
requirement related to the use of the equipment (i.e. licensing requirements).
Compliance to the requirements of the present document does not signify compliance to any safety requirement.
However, any temporary or permanent unsafe condition caused by EMC is considered as non-compliance.
2 References
The following documents contain provisions, which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific;
• for a specific reference, subsequent revisions do not apply;
• for a non-specific reference, subsequent revisions do apply. In the case of a reference to a 3GPP document
(including a GSM document), a non-specific reference implicitly refers to the latest version of that document in
the same Release as the present document.
[1] 3GPP TS 25.113: "Base station and repeater electromagnetic compatibility (EMC)".
[2] 3GPP TS 34.121: "Terminal conformance specification, Radio transmission and reception (FDD)".
[3] 3GPP TS 34.122: "Terminal conformance specification, Radio transmission and reception (TDD)".
[4] IEC 61000-6-1 (1997): "Electromagnetic compatibility (EMC) - Part 6: Generic standards -
Section 1: Immunity standard for residential, commercial and light-industrial environments".
ETSI
---------------------- Page: 7 ----------------------
3GPP TS 34.124 version 15.0.0 Release 15 7 ETSI TS 134 124 V15.0.0 (2018-07)
[5] IEC 61000-6-3 (1996): "Electromagnetic compatibility (EMC) - Part 6: Generic standards -
Section 3: Emission standard for residential, commercial and light-industrial environments.
[6] ISO 7637-1 (1990): "Road vehicles - Electrical disturbance by conduction and coupling - Part 1:
Passenger cars and light commercial vehicles with nominal 12 V supply voltage - Electrical
transient conduction along supply lines only".
[7] ISO 7637-2 (1990): "Road vehicles - Electrical disturbance by conduction and coupling - Part 2:
Commercial vehicles with nominal 24 V supply voltage - Electrical transient conduction along
supply lines only".
[8] 3GPP TR 25.990: "Vocabulary for UTRAN".
3GPP TR 21.905: "Vocabulary for 3GPP Specifications".
[9] IEC 60050(161): "International Electrotechnical Vocabulary - Chapter 161: Electromagnetic
compatibility".
[10] 3GPP TS 34.108: "Common test environments for User Equipment (UE); Conformance testing".
[11] ITU-R Recommendation SM.329: "Unwanted emissions in the spurious domain ".
[12] 3GPP TS 25.101: "User Equipment (UE) radio transmission and reception (FDD)".
[13] 3GPP TS 25.102: "User Equipment (UE) radio transmission and reception (TDD)".
[14] IEC CISPR publication 22: "Information technology equipment; Radio disturbance characteristics
- Limits and methods of measurement".
[15] 3GPP TS 34.109: "Terminal logical test interface; Special conformance testing functions".
[16] IEC CISPR publication 16-1: "Specification for radio disturbance and immunity measuring
apparatus and methods".
[17] IEC 61000-3-2; (2000): "Electromagnetic compatibility; Part 3 - Limits; section 2 - Limits for
harmonic current emissions (equipment input current ≤ 16 A per phase)"; Am.1 (1997-09)".
[18] IEC 61000-3-3; (19952): "Electromagnetic compatibility; Part 3 - Limits; section 2 - Limitation of
voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current
≤ 16 A"
[19] IEC 61000-4-2: "Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques - section 2: Electrostatic discharge immunity test - Basic EMC publication".
[20] IEC 61000-4-3: "Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques - section 3: Radiated, radio-frequency electromagnetic field immunity test".
[21] IEC 61000-4-4: "Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques - section 4: Electrical fast transient/burst immunity test - Basic EMC publication".
[22] IEC 61000-4-5: "Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques - section 5: Surge immunity test".
[23] IEC 61000-4-6: "Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques - section 6: immunity to conducted disturbances induced by radio frequency fields".
[24] IEC 61000-4-11: "Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques - section 11:Voltage dips, short interruptions, and voltage variations immunity test".
[25] ETSI ETR 027 (1991): "Radio Equipment and Systems (RES); Methods of measurement for
private mobile radio equipment".
[26] ITU-T Recommendation P.64: "Telephone transmission quality, Telephone installations, Local
line networks, Objective electro-acoustical measurements. Determination of sensitivity/frequency
characteristics of local telephone systems".
ETSI
---------------------- Page: 8 ----------------------
3GPP TS 34.124 version 15.0.0 Release 15 8 ETSI TS 134 124 V15.0.0 (2018-07)
[27] ITU-T Recommendation P.76: "Telephone transmission quality, Measurements related to speech
loudness, Determination of loudness ratings; Fundamental principles, Annex A".
[28] ITU-R Recommendation SM.1539 (2001): "Variation of the boundary between the out-of-band
and spurious domains required for the application of Recommendations ITU-R SM.1541 and ITU-
R SM.329".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply.
Ancillary equipment: Equipment (apparatus), used in connection with a user equipment (UE) is considered as an
ancillary equipment (apparatus) if:
- the equipment is intended for use in conjunction with a UE to provide additional operational and/or control
features to the UE, (e.g. to extend control to another position or location); and
- the equipment cannot be used on a stand alone basis to provide user functions independently of a UE; and
- the UE to which it is connected, is capable of providing some intended operation such as transmitting and/or
receiving without the ancillary equipment (i.e. it is not a sub-unit of the main equipment essential to the main
equipment basic functions).
BLER (BLock Error Ratio): BLER is block error ratio. The BLER calculation shall be based on evaluating the CRC
on each transport block .
Camped on a cell: The UE is in idle mode and has completed the cell selection/reselection process and has chosen a
cell. The UE monitors system information and (in most cases) paging information. Note that the services may be
limited, and that the PLMN may not be aware of the existence of the UE within the chosen cell.
Continuous phenomena (continuous disturbance): Electromagnetic disturbance, the e
...