|
TECHNICAL SPECIFICATION
5G;
NR;
Base Station (BS) radio transmission and reception
(3GPP TS 38.104 version 15.2.0 Release 15)
---------------------- Page: 1 ----------------------
3GPP TS 38.104 version 15.2.0 Release 15 1 ETSI TS 138 104 V15.2.0 (2018-07)
Reference
RTS/TSGR-0438104vf20
Keywords
5G
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 38.104 version 15.2.0 Release 15 2 ETSI TS 138 104 V15.2.0 (2018-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 38.104 version 15.2.0 Release 15 3 ETSI TS 138 104 V15.2.0 (2018-07)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 9
1 Scope . 10
2 References . 10
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 15
3.3 Abbreviations . 16
4 General . 18
4.1 Relationship with other core specifications . 18
4.2 Relationship between minimum requirements and test requirements . 18
4.3 Conducted and radiated requirement reference points . 18
4.3.1 BS type 1-C . 18
4.3.2 BS type 1-H . 19
4.3.3 BS type 1-O and BS type 2-O . 20
4.4 Base station classes . 20
4.5 Regional requirements . 21
4.6 Applicability of requirements . 21
4.7 Requirements for contiguous and non-contiguous spectrum . 22
4.8 Requirements for BS capable of multi-band operation . 22
4.9 OTA co-location with other base stations . 24
5 Operating bands and channel arrangement . 25
5.1 General . 25
5.2 Operating bands . 25
5.3 BS channel bandwidth . 26
5.3.1 General . 26
5.3.2 Transmission bandwidth configuration . 26
5.3.3 Minimum guardband and transmission bandwidth configuration . 26
5.3.4 RB alignment with different numerologies . 30
5.3.5 BS channel bandwidth per operating band . 30
5.4 Channel arrangement . 33
5.4.1 Channel spacing . 33
5.4.1.1 Channel spacing for adjacent NR carriers . 33
5.4.1.2 Channel spacing for CA . 34
5.4.2 Channel raster . 34
5.4.2.1 NR-ARFCN and channel raster. 34
5.4.2.2 Channel raster to resource element mapping. 35
5.4.2.3 Channel raster entries for each operating band . 35
5.4.3 Synchronization raster . 36
5.4.3.1 Synchronization raster and numbering . 36
5.4.3.2 Synchronization raster to synchronization block resource element mapping . 37
5.4.3.3 Synchronization raster entries for each operating band. 37
6 Conducted transmitter characteristics . 39
6.1 General . 39
6.2 Base station output power . 39
6.2.1 General . 39
6.2.2 Minimum requirement for BS type 1-C. 39
6.2.3 Minimum requirement for BS type 1-H . 40
6.2.4 Additional requirements (regional) . 40
6.3 Output power dynamics . 40
6.3.1 General . 40
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 38.104 version 15.2.0 Release 15 4 ETSI TS 138 104 V15.2.0 (2018-07)
6.3.2 RE power control dynamic range . 40
6.3.2.1 General . 40
6.3.2.2 Minimum requirement for BS type 1-C and BS type 1-H . 40
6.3.3 Total power dynamic range . 40
6.3.3.1 General . 40
6.3.3.2 Minimum requirement for BS type 1-C and BS type 1-H . 41
6.4 Transmit ON/OFF power . 41
6.4.1 Transmitter OFF power . 41
6.4.1.1 General . 41
6.4.1.2 Minimum requirement for BS type 1-C . 41
6.4.1.3 Minimum requirement for BS type 1-H . 41
6.4.2 Transmitter transient period . 42
6.4.2.1 General . 42
6.4.2.2 Minimum requirement for BS type 1-C and BS type 1-H . 42
6.4.2.3 Void. 42
6.5 Transmitted signal quality . 42
6.5.1 Frequency error . 42
6.5.1.1 General . 42
6.5.1.2 Minimum requirement for BS type 1-C and BS type 1-H . 43
6.5.2 Modulation quality . 43
6.5.2.1 General . 43
6.5.2.2 Minimum Requirement for BS type 1-C and BS type 1-H . 43
6.5.2.3 EVM frame structure for measurement . 43
6.5.3 Time alignment error . 43
6.5.3.1 General . 43
6.5.3.2 Minimum requirement for BS type 1-C and 1-H . 44
6.6 Unwanted emissions . 44
6.6.1 General . 44
6.6.2 Occupied bandwidth . 45
6.6.2.1 General . 45
6.6.2.2 Minimum requirement for BS type 1-C and BS type 1-H . 45
6.6.3 Adjacent Channel Leakage Power Ratio . 45
6.6.3.1 General . 45
6.6.3.2 Limits and Basic limits . 45
6.6.3.3 Minimum requirement for BS type 1-C . 48
6.6.3.4 Minimum requirement for BS type 1-H . 48
6.6.4 Operating band unwanted emissions . 49
6.6.4.1 General . 49
6.6.4.2 Basic limits . 51
6.6.4.2.1 Basic limits for Wide Area BS (Category A) . 51
6.6.4.2.2 Basic limits for Wide Area BS (Category B) . 51
6.6.4.2.2.1 Category B requirements (Option 1) . 51
6.6.4.2.2.2 Category B requirements (Option 2) . 53
6.6.4.2.3 Basic limits for Medium Range BS (Category A and B) . 53
6.6.4.2.4 Basic limits for Local Area BS (Category A and B) . 54
6.6.4.2.5 Basic limits for additional requirements . 54
6.6.4.2.5.1 Limits in FCC Title 47 . 54
6.6.4.3 Minimum requirements for BS type 1-C . 54
6.6.4.4 Minimum requirements for BS type 1-H . 54
6.6.5 Transmitter spurious emis sions . 55
6.6.5.1 General . 55
6.6.5.2 Basic limits . 55
6.6.5.2.1 General transmitter spurious emissions requirements . 55
6.6.5.2.2 Protection of the BS receiver of own or different BS . 56
6.6.5.2.3 Additional spurious emissions requirements . 56
6.6.5.2.4 Co-location with other base stations . 62
6.6.5.3 Minimum requirements for BS type 1-C . 66
6.6.5.4 Minimum requirements for BS type 1-H . 66
6.7 Transmitter intermodulation . 67
6.7.1 General . 67
6.7.2 Minimum requirements for BS type 1-C . 67
6.7.2.1 Co-location minimum requirements . 67
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 38.104 version 15.2.0 Release 15 5 ETSI TS 138 104 V15.2.0 (2018-07)
6.7.2.2 Additional requirements . 68
6.7.3 Minimum requirements for BS type 1-H . 68
6.7.3.1 Co-location minimum requirements . 68
6.7.3.2 Intra-system minimum requirements. 69
6.7.3.3 Additional requirements . 69
7 Conducted receiver characteristics . 70
7.1 General . 70
7.2 Reference sensitivity level . 70
7.2.1 General . 70
7.2.2 Minimum requirements for BS type 1-C and BS type 1-H . 70
7.3 Dynamic range . 72
7.3.1 General . 72
7.3.2 Minimum requirement for BS type 1-C and BS type 1-H . 72
7.4 In-band selectivity and blocking . 74
7.4.1 Adjacent Channel Selectivity (ACS) . 74
7.4.1.1 General . 74
7.4.1.2 Minimum requirement for BS type 1-C and BS type 1-H . 74
7.4.1.3 Void. 76
7.4.1.4 Void. 76
7.4.2 In-band blocking . 76
7.4.2.1 General . 76
7.4.2.2 Minimum requirement for BS type 1-C and BS type 1-H . 76
7.4.2.3 Void. 78
7.4.2.4 Void. 78
7.5 Out-of-band blocking . 78
7.5.1 General . 78
7.5.2 Minimum requirement for BS type 1-C and BS type 1-H . 78
7.5.3 Co-location minimum requirements for BS type 1-C and BS type 1-H . 79
7.5.4 Void . 80
7.6 Receiver spurious emissions. 80
7.6.1 General . 80
7.6.2 Basic limits . 80
7.6.3 Minimum requirement for BS type 1-C. 80
7.6.4 Minimum requirement for BS type 1-H . 81
7.7 Receiver intermodulation . 81
7.7.1 General . 81
7.7.2 Minimum requirement for BS type 1-C and BS type 1-H . 81
7.8 In-channel selectivity . 84
7.8.1 General . 84
7.8.2 Minimum requirement for BS type 1-C and BS type 1-H . 85
8 Performance requirements . 88
9 Radiated transmitter characteristics . 89
9.1 General . 89
9.2 Radiated transmit power . 89
9.2.1 General .
...