ETSI TS 125 142 V15.0.1 (2018-07)

Universal Mobile Telecommunications System (UMTS); Base Station (BS) conformance testing (TDD) (3GPP TS 25.142 version 15.0.1 Release 15)

ETSI TS 125 142 V15.0.1 (2018-07)

Name:ETSI TS 125 142 V15.0.1 (2018-07)   Standard name:Universal Mobile Telecommunications System (UMTS); Base Station (BS) conformance testing (TDD) (3GPP TS 25.142 version 15.0.1 Release 15)
Standard number:ETSI TS 125 142 V15.0.1 (2018-07)   language:English language
Release Date:25-Jul-2018   technical committee:3GPP RAN 4 - Specification for radio performance
Drafting committee:   ICS number:
ETSI TS 125 142 V15.0.1 (2018-07)






TECHNICAL SPECIFICATION
Universal Mobile Telecommunications System (UMTS);
Base Station (BS) conformance testing (TDD)
(3GPP TS 25.142 version 15.0.1 Release 15)

---------------------- Page: 1 ----------------------
3GPP TS 25.142 version 15.0.1 Release 15 1 ETSI TS 125 142 V15.0.1 (2018-07)



Reference
RTS/TSGR-0425142vF01
Keywords
UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at

If you find errors in the present document, please send your comment to one of the following services:

Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2018.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.

GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3GPP TS 25.142 version 15.0.1 Release 15 2 ETSI TS 125 142 V15.0.1 (2018-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 3 ----------------------
3GPP TS 25.142 version 15.0.1 Release 15 3 ETSI TS 125 142 V15.0.1 (2018-07)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 17
1 Scope . 18
2 References . 18
3 Definitions, symbols, and abbreviations . 19
3.1 Definitions . 19
3.2 Symbols . 20
3.3 Abbreviations . 20
4 Frequency bands and channel arrangement . 22
4.1 General . 22
4.2 Frequency bands . 22
4.3 TX-RX frequency separation . 23
4.3.1 3,84 Mcps TDD option . 23
4.3.2 1,28 Mcps TDD option . 23
4.3.3 7,68 Mcps TDD option . 23
4.4 Channel arrangement . 23
4.4.1 Channel spacing . 23
4.4.1.1 3,84 Mcps TDD option . 23
4.4.1.2 1,28 Mcps TDD option . 23
4.4.1.3 7,68 Mcps TDD option . 23
4.4.2 Channel raster . 23
4.4.2.1 3,84 Mcps TDD Option . 23
4.4.3 Channel number . 23
5 General test conditions and declarations . 24
5.1 Base station classes . 24
5.1.1 Applicability of requirements and BS class definition . 24
5.1.2 Manufacturer’s declaration of supported RF configurations . 24
5.2 Output power . 25
5.3 Specified frequency range and supported channel bandwidth . 25
5.3.1 RF bandwidth position for multi-carrier testing. 26
5.4 Relationship between RF generation and chip clock . 26
5.5 Spectrum emission mask . 26
5.6 Adjacent Channel Leakage power Ratio (ACLR) . 26
5.7 Tx spurious emissions . 27
5.7.1 Category of spurious emissions limit . 27
5.7.2 Co-existence with GSM . 27
5.7.3 Co-existence with DCS 1800 . 27
5.7.4 Co-existence with UTRA FDD . 27
5.7.5 Co-existence with unsynchronised UTRA TDD and/or E-UTRA TDD . 28
5.8 Blocking characteristics . 28
5.9 Test environments . 28
5.9.1 Normal test environment . 28
5.9.2 Extreme test environment . 29
5.9.2.1 Extreme temperature . 29
5.9.3 Vibration . 29
5.9.4 Power supply . 29
5.10 Acceptable uncertainty of Test System . 30
5.10.1 Measurement of test environments . 30
5.10.2 Measurement of transmitter . 31
5.10.3 Measurement of receiver . 36
5.10.4 Measurement of performance requirements . 38
ETSI

---------------------- Page: 4 ----------------------
3GPP TS 25.142 version 15.0.1 Release 15 4 ETSI TS 125 142 V15.0.1 (2018-07)
5.11 Test Tolerances (informative) . 38
5.11.1 Transmitter . 39
5.11.2 Receiver . 41
5.11.3 Performance requirements . 41
5.12 Interpretation of measurement results . 41
5.13 Selection of configurations for testing. 42
5.14 BS Configurations . 42
5.14.1 Receiver diversity . 42
5.14.2 Duplexers . 43
5.14.3 Power supply options . 43
5.14.4 Ancillary RF amplifiers . 43
5.14.5 BS using antenna arrays . 43
5.14.5.1 Receiver tests . 43
5.14.5.2 Transmitter tests . 44
5.14.6 MIMO transmission . 44
5.15 Overview of the conformance test requirements . 44
5.16 Format and interpretation of tests . 46
5.17 Regional requirements . 46
5.18 Definition of Additive White Gaussian Noise (AWGN) Interferer . 47
5.19 Applicability of requirements . 47
5.20 Test configurations for multi-carrier operation . 48
5.20.1 UTTC1: Multi-carrier operation test configuration . 48
5.20.1.1 UTTC1 generation . 48
5.20.1.1 UTTC1 power allocation . 48
5.20.2 UTTC2: Multi-band test configuration for full carrier allocation . 48
5.20.2.1 UTTC2 generation . 48
5.20.2.2 UTTC2 power allocation . 49
5.21 Applicability of test configurations . 49
5.22 Requirements for BS capable of multi-band operation . 51
6 Transmitter characteristics . 52
6.1 General . 52
6.1.1 IMB Test Models . 52
6.1.1.1 IMB Test Model 1 - TM 1 . 52
6.1.1.2 IMB Test Model 2 - TM 2 . 53
6.2 Maximum output power . 53
6.2.1 Definition and applicability . 53
6.2.2 Minimum Requirements . 53
6.2.3 Test purpose . 53
6.2.4 Method of test . 54
6.2.4.1 Initial conditions . 54
6.2.4.1.0 General test conditions . 54
6.2.4.1.1 3,84 Mcps TDD option . 54
6.2.4.1.2 1,28 Mcps TDD option . 54
6.2.4.1.3 7,68 Mcps TDD option . 55
6.2.4.2 Procedure . 55
6.2.4.2.1 3,84 Mcps TDD option . 55
6.2.4.2.2 1,28 Mcps TDD option . 55
6.2.4.2.3 7,68 Mcps TDD option . 55
6.2.5 Test Requirements . 56
6.3 Frequency stability . 56
6.3.1 Definition and applicability . 56
6.3.2 Minimum Requirements . 56
6.3.3 Test purpose . 56
6.3.4 Method of test . 56
6.3.4.1 Initial conditions . 56
6.3.4.1.0 General test conditions . 56
6.3.4.1.1 3,84 Mcps TDD option . 57
6.3.4.1.2 1,28 Mcps TDD option . 57
6.3.4.1.3 7,68 Mcps TDD option . 57
6.3.4.2 Procedure . 58
6.3.5 Test Requirements . 58
ETSI

---------------------- Page: 5 ----------------------
3GPP TS 25.142 version 15.0.1 Release 15 5 ETSI TS 125 142 V15.0.1 (2018-07)
6.4 Output power dynamics . 58
6.4.1 Inner loop power control . 58
6.4.2 Power control steps . 59
6.4.2.1 Definition and applicability . 59
6.4.2.2 Minimum Requirements . 59
6.4.2.3 Test purpose . 59
6.4.2.4 Method of test . 59
6.4.2.4.1 Initial conditions . 59
6.4.2.4.1.0 General test conditions . 59
6.4.2.4.1.1 3,84 Mcps TDD option . 59
6.4.2.4.1.2 1,28 Mcps TDD option . 60
6.4.2.4.1.3 7,68 Mcps TDD option . 60
6.4.2.4.2 Procedure . 61
6.4.2.4.2.1 3,84 Mcps TDD option . 61
6.4.2.4.2.2 1,28 Mcps TDD option . 61
6.4.2.4.2.3 7,68 Mcps TDD option . 62
6.4.2.5 Test Requirements . 62
6.4.2.5.1 3,84 Mcps TDD option . 62
6.4.2.5.2 1,28 Mcps TDD option . 62
6.4.2.5.3 7,68 Mcps TDD option . 63
6.4.3 Power control dynamic range . 63
6.4.3.1 Definition and applicability . 63
6.4.3.2 Minimum Requirements . 63
6.4.3.3 Test purpose . 63
6.4.3.4 Method of test . 63
6.4.3.4.1 Initial conditions . 63
6.4.3.4.1.0 General test conditions . 63
6.4.3.4.1.1 3,84 Mcps TDD option . 63
6.4.3.4.1.2 1,28 Mcps TDD option . 64
6.4.3.4.1.3 7,68 Mcps TDD option . 64
6.4.3.4.2 Procedure . 65
6.4.3.4.2.1 3,84 Mcps TDD option . 65
6.4.3.4.2.2 1,28 Mcps TDD option . 65
6.4.3.4.2.3 7,68 Mcps TDD option . 66
6.4.3.5 Test Requirements . 66
6.4.4 Minimum output power . 66
6.4.4.1 Definition and applicability . 66
6.4.4.2 Minimum Requirements . 66
6.4.4.3 Test purpose . 66
6.4.4.4 Method of test . 67
6.4.4.4.1 Initial conditions . 67
6.4.4.4.1.0 General test conditions . 67
6.4.4.4.1.1 3,84 Mcps TDD option . 67
6.4.4.4.1.2 1,28
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27