|
TECHNICAL SPECIFICATION
Intelligent Transport Systems (ITS);
Testing;
Conformance test specifications for ITS Security;
Part 1: Protocol Implementation Conformance
Statement (PICS)
---------------------- Page: 1 ----------------------
2 ETSI TS 103 096-1 V1.4.1 (2018-08)
Reference
RTS/ITS-00542
Keywords
ITS, PICS, security
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI TS 103 096-1 V1.4.1 (2018-08)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definitions and abbreviations . 6
3.1 Definitions . 6
3.2 Abbreviations . 6
4 Conformance . 6
Annex A (normative): Security PICS pro forma . 7
A.1 The right to copy . 7
A.2 Guidance for completing the PICS pro forma . 7
A.2.1 Purposes and structure . 7
A.2.2 Abbreviations and conventions . 7
A.2.3 Instructions for completing the PICS pro forma. 8
A.3 Identification of the Equipment . 9
A.3.1 Introduction . 9
A.3.2 Date of the statement . 9
A.3.3 Equipment Under Test identification . 9
A.3.4 Product supplier . 9
A.3.5 Client . 10
A.3.6 PICS contact person . 10
A.4 Identification of the protocol . 11
A.5 Global statement of conformance . 11
A.6 PICS pro forma tables . 11
History . 13
ETSI
---------------------- Page: 3 ----------------------
4 ETSI TS 103 096-1 V1.4.1 (2018-08)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Intelligent Transport Systems
(ITS).
The present document is part 1 of a multi-part deliverable covering Conformance test specifications for ITS Security, as
identified below:
Part 1: "Protocol Implementation Conformance Statement (PICS)";
Part 2: "Test Suite Structure and Test Purposes (TSS & TP)";
Part 3: "Abstract Test Suite (ATS) and Protocol Implementation eXtra Information for Testing (PIXIT)".
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 4 ----------------------
5 ETSI TS 103 096-1 V1.4.1 (2018-08)
1 Scope
The present document provides the Protocol Implementation Conformance Statement (PICS) pro forma for the test
specifications for security algorithms as specified in ETSI TS 103 097 [1] and in accordance with the relevant guidance
given in ISO/IEC 9646-7 [i.2] and ETSI ETS 300 406 [i.3].
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI TS 103 097 (V1.3.1): "Intelligent Transport Systems (ITS); Security; Security header and
certificate formats".
[2] IEEE Std 1609.2™-2016: "IEEE Standard for Wireless Access in Vehicular Environments -
Security Services for Applications and Management Messages", as amended by IEEE Std
1609.2a™-2017: "IEEE Standard for Wireless Access In Vehicular Environments - Security
Services for Applications and Management Messages - Amendment 1".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ISO/IEC 9646-1: "Information technology -- Open Systems Interconnection -- Conformance
testing methodology and framework -- Part 1: General concepts".
[i.2] ISO/IEC 9646-7: "Information technology -- Open Systems Interconnection -- Conformance
testing methodology and framework -- Part 7: Implementation Conformance Statements".
[i.3] ETSI ETS 300 406: "Methods for testing and Specification (MTS); Protocol and profile
conformance testing specifications; Standardization methodology".
ETSI
---------------------- Page: 5 ----------------------
6 ETSI TS 103 096-1 V1.4.1 (2018-08)
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI TS 103 097 [1] and in
ISO/IEC 9646-1 [i.1] apply.
3.2 Abbreviations
For the purposes of the present document, the abbreviations given in ETSI TS 103 097 [1] and the following apply:
CRL Certificate Revocation List
GN-MGMT GeoNetworking Management message
P2PCD Peer-to-Peer Certificate Distribution
PDU Protocol Data Unit
PICS Protocol Implementation Conformance Statement
4 Conformance
a) A PICS pro forma which conforms to this PICS pro forma specification shall be technically equivalent to
annex A of the IEEE Std 1609.2 [2] and to annex A of the present document and shall preserve the numbering
and ordering of the items in annex A.
b) The following clauses of the IEEE Std 1609.2 [2] are irrelevant for conformance with ETSI TS 103 097 [1]
and may be skipped:
- A.2.3.2 Certificate revocation list (CRL) verification entity;
- A.2.3.3 Peer-to-peer certificate distribution (P2PCD) functionality (S3.1, S3.2, S3.3, S3.4).
A PICS which conforms to the present document shall:
a) describe an implementation which claims to conform to ETSI TS 103 097 [1] and IEEE Std 1609.2 [2];
b) be a conforming PICS pro forma which has been completed in accordance with the instructions for completion
given in clause A.2;
c) include the information necessary to uniquely identify both the supplier and the implementation.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI TS 103 096-1 V1.4.1 (2018-08)
Annex A (normative):
Security PICS pro forma
A.1 The right to copy
Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that
users of the present document may freely reproduce the Security PICS pro forma in this annex so that it can be used for
its intended purposes and may further publish the completed PICS pro forma.
A.2 Guidance for completing the PICS pro forma
A.2.1 Purposes and structure
The purpose of the present document is to provide a mechanism whereby a supplier of an implementation of the
requirements defined in relevant specifications may provide information about the implementation in a standardized
manner.
The PICS pro forma is subdivided into clauses for the following categories of information:
- instructions for completing the PICS pro forma;
- identification of the implementation;
- identification of the protocol;
- PICS pro forma tables (for example: major capabilities, etc.).
A.2.2 Abbreviations and conventions
This annex does not reflect dynamic conformance requirements but static ones. In particular, a conditi
...