|
TECHNICAL SPECIFICATION
LTE;
Evolved Universal Terrestrial
Radio Access Network (E-UTRAN);
Architecture description
(3GPP TS 36.401 version 15.0.0 Release 15)
---------------------- Page: 1 ----------------------
3GPP TS 36.401 version 15.0.0 Release 15 1 ETSI TS 136 401 V15.0.0 (2018-09)
Reference
RTS/TSGR-0336401vf00
Keywords
LTE
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 36.401 version 15.0.0 Release 15 2 ETSI TS 136 401 V15.0.0 (2018-09)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 36.401 version 15.0.0 Release 15 3 ETSI TS 136 401 V15.0.0 (2018-09)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 5
1 Scope . 6
2 References . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 7
4 General principles . 8
5 General architecture . 9
5.1 General . 9
5.2 User plane . 9
5.3 Control plane . 9
6 E-UTRAN architecture. 10
6.1 Overview . 10
6.2 E-UTRAN identifiers . 11
6.2.1 Principle of handling Application Protocol Identities . 11
6.2.2 PLMN Identity . 12
6.2.3 Globally Unique MME Identifier (GUMMEI) . 12
6.2.4 Global eNB ID . 12
6.2.5 E-UTRAN Cell Global Identifier (ECGI) . 12
6.2.6 Tracking Area Identity . 12
6.2.7 E-RAB ID . 13
6.2.8 UE Identifiers . 13
6.2.8.1 Radio Network Temporary Identifiers (RNTI) . 13
6.2.8.2 S-Temporary Mobile Subscriber Identity (S-TMSI) . 13
6.3 Transport addresses . 13
6.4 UE associations in eNB . 13
7 E-UTRAN functions description . . 14
7.1 List of functions . 14
7.2 Functions description . 14
7.2.1 Transfer of user data . 14
7.2.2 Radio channel ciphering and deciphering . 15
7.2.3 Integrity protection . 15
7.2.4 Header compression . 15
7.2.5 Mobility control functions . 15
7.2.5.1 Handover . 15
7.2.5.2 void . 15
7.2.5.3 void . 15
7.2.5.4 Dual Connectivity . 15
7.2.6 Inter-cell interference coordination . 15
7.2.7 Connection set-up and release . 15
7.2.8 Load balancing . 16
7.2.9 Distribution function for NAS messages . 16
7.2.10 NAS node selection function . 16
7.2.11 Synchronization . 16
7.2.12 Radio Access Network (RAN) sharing . 16
7.2.13 MBMS function . 16
7.2.14 Subscriber and equipment trace . 16
7.2.15 RAN Information Management (RIM) . 16
7.2.16 Paging . 17
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 36.401 version 15.0.0 Release 15 4 ETSI TS 136 401 V15.0.0 (2018-09)
7.2.17 Positioning . 17
7.2.18 Delivery of warning messages . 17
8 Mobility management. 17
8.1 Signalling connection . 17
8.2 Consequences for mobility handling . 17
9 Synchronization . 18
9.1 eNB Synchronization . 18
9.2 eNB and MME Synchronization . 19
10 void . 19
11 E-UTRAN interfaces . 19
11.1 General protocol model for E-UTRAN interfaces . 19
11.1.1 Radio Network Layer (RNL) and Transport Network Layer (TNL) . 19
11.1.2 Control plane . 19
11.1.3 User plane . 19
11.2 Iuant interface - general principles . 20
Annex A (informative): Change history . 21
History . 22
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 36.401 version 15.0.0 Release 15 5 ETSI TS 136 401 V15.0.0 (2018-09)
Foreword
rd
This Technical Specification has been produced by the 3 Generation Partnership Project (3GPP).
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z the third digit is incremented when editorial only changes have been incorporated in the document.
ETSI
---------------------- Page: 6 ----------------------
3GPP TS 36.401 version 15.0.0 Release 15 6 ETSI TS 136 401 V15.0.0 (2018-09)
1 Scope
The present document describes the overall architecture of the E-UTRAN, including internal interfaces and assumptions
on the radio, S1 and X2 interfaces.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
- References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
- For a specific reference, subsequent revisions do not apply.
- For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including
a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same
Release as the present document.
[1] 3GPP TR 21.905: "Vocabulary for 3GPP Specifications".
[2] 3GPP TS 36.300: "Evolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Universal
Terrestrial Radio Access Network (E-UTRAN) Overall description Stage 2".
[3] 3GPP TS 23.401: "General Packet Radio Service (GPRS) enhancements for Evolved Universal
Terrestrial Radio Access Network (E-UTRAN) access".
[4] 3GPP TS 36.414: "Evolved Universal Terrestrial Access Network (E-UTRAN); S1 data transport".
[5] 3GPP TS 36.424: "Evolved Universal Terrestrial Access Network (E-UTRAN); X2 data
transport".
[6] 3GPP TS 36.440: "Evolved Universal Terrestrial Radio Access Network (E-UTRAN); General
aspects and principles for interfaces supporting Multimedia Broadcast Multicast Service (MBMS)
within E-UTRAN".
[7] ITU-T Recommendation G.823 (2000-03): "The control of jitter and wander within digital
networks which are based on the 2048 kbit/s hierarchy".
[8] ITU-T Recommendation G.824 (2000-03): "The control of jitter and wander within digital
networks which are based on the 1544 kbit/s hierarchy".
[9] ITU-T Recommendation G.825 (2001-08): "The control of jitter and wander within digital
networks which are based on the synchronous digital hierarchy (SDH)".
[10] ITU-T Recommendation G.8261/Y.1361 (2008-04): "Timing and Synchronization aspects in
Packet networks".
[11] 3GPP TS 23.003: "Numbering, addressing and identification".
[12] 3GPP TR 44.901: "External Network Assisted Cell Change (NACC)".
[13] 3GPP TS 48.018: "General Packet Radio Service (GPRS); Base Station System (BSS) - Serving
GPRS Support Node (SGSN); BSS GPRS Protocol (BSSGP)".
[14] 3GPP TS 23.251: "Network Sharing; Architecture and functional description".
[15] 3GPP TS 22.268: "Public Warning System (PWS) requirements".
[16] 3GPP TS 33.401: "3GPP System Architecture Evolution (SAE); Security architecture".
[17] 3GPP TS 32.421: "Telecommunication management; Subscriber and equipment trace; Trace
concepts and requirements".
ETSI
---------------------- Page: 7 ----------------------
3GPP TS 36.401 version 15.0.0 Release 15 7 ETSI TS 136 401 V15.0.0 (2018-09)
[18] 3GPP TS 32.422: "Telecommunication management; Subscriber and equipment trace; Trace
control and configuration management".
[19] 3GPP TS 32.423: "Telecommunication management; Subscriber and equipment trace; Trace data
definition and management".
[20] 3GPP TS 32.441: "Telecommunication management; Trace Management Integration Reference
Point (IRP); Requirements".
[21] 3GPP TS 32.442: "Telecommunication management; Trace Management Integration Reference
Point (IRP); Information Service (IS)".
[22] 3GPP TS 32.446: "Telecommunication management; Trace Management Integration Reference
Point (IRP); Solution Set (SS) definitions".
[23] 3GPP TS 25.411: "UTRAN Iu interface layer 1".
[24] 3GPP TS 23.682: "Architecture enhancements to facilitate communications with packet data
networks and applications".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in TR 21.905 [1] and the following apply.
A term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905 [1].
Dual Connectivity: Defined in TS 36.300 [2].
E-RAB: An E-RAB uniquely identifies the concatenation of an S1 Bearer and the corresponding Data Radio Bearer.
When an E-RAB exists, there is a one-to-one mapping between this E-RAB and an EPS bearer of the Non Access
Stratum (NAS) as defined in TS 23.401 [3].
S1: logical interface between an eNB and an EPC, providing an interconnection point between the E-UTRAN and the
EPC. It is also considered as a reference point.
X2: logical interface between two eNBs. Whilst logically representing a point-to-point link between eNBs, the physical
realization need not be a point-to-point link.
3.2 Abbreviations
For the purposes of the present document, the terms and definitions given in TR 21.905 [1] and the following apply.
A term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905 [1].
AP Application Protocol
AS Access Stratum
CGI Cell Global Identifier
CIoT Cellular IoT
CMAS Commercial Mobile Alert Service
C-RNTI Cell RNTI
ECGI E-UTRAN Cell Global Identifier
ECM EPS Connection Management
EEC Ethernet Equipment Clock
eNB E-UTRAN Node B
EMM EPS Mobility Management
E-RAB E-UTRAN Radio Access Bearer
ESM EPS Session Management
E-SMLC Evolved Serving Mobile Location Centre
ETWS Earthquake and Tsunami Warning System
EPC Evolved Packet Core
EPS Evolved Packet System
E-UTRA Evolved UTRA
ETSI
---------------------- Page: 8 ----------------------
3GPP TS 36.401 version 15.0.0 Release 15 8 ETSI TS 136 401 V15.0.0 (2018-09)
E-UTRAN Evolved UTRAN
FDD Frequency Division Duplex
GUMMEI Globally Unique MME Identifier
ID Identity
IP Internet Protocol
LTE Long Term Evolution
MBMS Multimedia Broadcast Multicast Service
MBSFN Multimedia Broadcast multicast service Single Frequency Network
MeNB Master eNB
NDS Network Domain Security
MME Mobility Management Entity
NAS Non-Access Stratum
OTDOA Observed Time Difference Of Arrival (positioning method)
PLMN Public Land Mobile Network
PWS Public Warning System
RA-RNTI Random Access RNTI
RET Remote Electrical Tilting
RIM RAN Information Management
RNL Radio Network Layer
RNTI Radio Network Temporary Identifier
RRC Radio Resource Control
RTP Real-time Transport Protocol
QoS Quality of Service
SFN System Frame Number
S-GW Serving Gateway
SAP Service Access Point
SCG Secondary Cell Group
SeNB Secondary eNB
SON Self Organizing Networks
S-TMSI S-Temporary Mobile Subscriber Identity
TCP Transmission Control Protocol
TDD Time Division Duplex
TDM Time Division Multiplexing
TMA Tower Mounted Amplifier
TNL Transport Network Layer
UDP User Datagram Protocol
UE User Equipment
UMTS Universal Mobile Telecommunication System
UTDOA Uplink Time Difference of Arrival
4 General principles
The general principles guiding the definition of E-UTRAN architecture as well as the E-UTRAN interfaces are the
following:
- Logical separation of signalling and data transport networks.
- E-UTRAN and EPC functions are fully separated from transport functions. Addressing scheme used in
E-UTRAN and EPC shall not be tied to the addressing schemes of transport functions. The fact that some
E-UTRAN or EPC functions reside in the same equipment as some transport functions does not make the
transport functions part of the E-UTRAN or the EPC.
- Mobility for RRC connection is fully controlled by the E-UTRAN.
- When defining the E-UTRAN interfaces the following principles were followed:
● The functional division across the interfaces shall have as few options as possible;
● Interfaces should be based on a logical model of the entity controlled through this interface;
● One physical network element can implement multiple logical nodes.
ETSI
---------------------- Page: 9 ----------------------
3GPP TS 36.401 version 15.0.0 Release 15 9 ETSI TS 136 401 V15.0.0 (2018-09)
5 General architecture
5.1 General
The protocols over Uu and S1 interfaces are divided into two structures:
- User plane protocols
These are the protocols implementing the actual E-RAB service, i.e. carrying user data through the access
stratum.
- Control plane protocols
These are the protocols for controlling the E-RABs and the connection between the UE and the network from
different aspects (including requesting the service, controlling different transmission resources, handover etc.).
Also a mechanism for transparent transfer of NAS messages is included.
5.2 User plane
The E-RAB service is offered from SAP to SAP by the Access Stratum. Figure 5.2-1 shows the protocols on the Uu and
S1 interfaces that linked together provide this E-RAB service.
Non-Access Stratum
Radio
Radio
S1 S1
proto-
proto- proto proto
cols
cols cols
cols
(1)
(1)
(2) (2)
Access Stratum
EPC
UE
EUTRAN
Radio
S1
(Uu)
Note 1: The radio interface protocols are defined in 3GPP TS 36.2xx and TS 36.3xx.
Note 2: The S1 interface protocols are defined in 3GPP TS 36.41x.
Figure 5.2-1: S1 and Uu user plane
5.3 Control plane
Figure 5.3-1 shows the control plane (signalling) protocol stacks on S1 and Uu interfaces.
ETSI
---------------------- Page: 10 ----------------------
3GPP TS 36.401 version 15.0.0 Release 15 10 ETSI TS 136 401 V15.0.0 (2018-09)
(3)
EMM,ESM EMM,ESM(3)
Non-Access Stratum
S1 S1
Radio
Radio
proto-
proto- proto proto
cols
cols cols
cols
(1)
(2) (2)
(1)
Access Stratum
EPC
UE
EUTRAN
Radio
S1
(Uu)
Note 1: The radio interface protocols are defined in 3GPP TS 36.2xx and TS 36.3xx.
Note 2: The protocol is defined in 3GPP TS 36.41x. (Description of S1 interface).
Note 3: EMM, ESM: This exemplifies a set of NAS control protocols between UE and EPC. The evolution of the
protocol architecture for these protocols is outside the scope of the present document.
Figure 5.3-1: S1 and Uu control plane
NOTE: Both the Radio protocols and the S1 protocols contain a mechanism to transparently transfer NAS
messages.
6 E-UTRAN architecture
6.1 Overview
EPC
S1 S1
X2
EUTRAN
eNB eNB
Figure 6.1-1 Overall architecture
The LTE architecture can be further described as follows:
The E-UTRAN consists of a set of eNBs connected to the EPC through the S1.
An eNB can support FDD mode, TDD mode or dual mode operation.
eNBs can be interconnected through the X2.
S1 and X2 are logical interfaces.
The E-UTRAN is layered into a Radio Network Layer (RNL) and a Transport Network Layer (TNL).
The E-UTRAN architecture, i.e. the E-UTRAN logical nodes and interfaces between them, is defined as part of the
RNL.
ETSI
---------------------- Page: 11 ----------------------
3GPP TS 36.401 version 15.0.0 Release 15 11 ETSI TS 136 401 V15.0.0 (2018-09)
For each E-UTRAN interface (S1, X2) the related TNL protocol and the functionality are specified. The TNL provides
services for user plane transport, signalling transport.
In S1-Flex configuration, each eNB is connected to all EPC nodes within a pool area. The pool area is defined in
3GPP TS 23.401 [3].
If security protection for control plane and user plane data on TNL of E-UTRAN interfaces has to be supported,
NDS/IP (3GPP TS 33.401 [16] shall be applied.
The eMBMS architecture is defined in 3GPP TS 36.440 [6].
6.2 E-UTRAN identifiers
This subclause shows those identifiers that are used in E-UTRAN.
6.2.1 Principle of handling Application Protocol Identities
An Application Protocol Identity (AP ID) is allocated when a new UE-associated logical connection is created in an
eNB, or an MME, or in a WT. An AP ID shall uniquely identify a logical connection associated to a UE over the S1
interface, or X2 interface, or Xw interface within a node (eNB, or MME, or WT). Upon receipt of a message that has a
new AP ID from the sending node, the receiving node shall store the AP ID of the sending node for the duration of the
logical connection. The receiving node shall assign the AP ID to be used to identify the logical connection associated to
the UE and include it as well as the previously received new AP ID from the sending node, in the first returned message
to the sending node. In all subsequent messages to and from sending node, both AP IDs of sending node and receiving
node shall be included.
The definitions of AP IDs as used on S1 interface, or X2 interface, or Xw interface are shown below:
eNB UE S1AP ID:
An eNB UE S1AP ID shall be allocated so as to uniquely identify the UE over the S1 interface within an eNB.
When an MME receives an eNB UE S1AP ID it shall store it for the duration of the UE-associated logical S1-
connection for this UE. Once known to an MME this is included in all UE associated S1-AP signalling.
The eNB UE S1AP ID shall be unique within t
...