|
TECHNICAL SPECIFICATION
Universal Mobile Telecommunications System (UMTS);
LTE;
Common test environments for User Equipment (UE);
Conformance testing
(3GPP TS 34.108 version 14.3.0 Release 14)
---------------------- Page: 1 ----------------------
3GPP TS 34.108 version 14.3.0 Release 14 1 ETSI TS 134 108 V14.3.0 (2018-10)
Reference
RTS/TSGR-0534108ve30
Keywords
LTE,UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 34.108 version 14.3.0 Release 14 2 ETSI TS 134 108 V14.3.0 (2018-10)
Content
Foreword . 3
Modal verbs terminology . 3
Introduction . 3
1 Scope . 4
2 References . 4
3 Definitions, abbreviations and symbols . 4
4 Common requirements of test equipment. 4
5 to 11 Void . 4
Annex A to C (informative): Void . 5
Annex D (informative): Change history . 6
History . 30
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 34.108 version 14.3.0 Release 14 3 ETSI TS 134 108 V14.3.0 (2018-10)
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z the third digit is incremented when editorial only changes have been incorporated in the document.
Introduction
The definition of the Conformance Tests for UE in 3G will be a complex task as the complete test suite covers RF,
EMC and Protocol aspects of the UE.
Each test requires a Test Environment to be defined in which the UE has to operate to defined standards, constraints and
performance. The overall task can be simplified if there are a number of well defined and agreed Common Test
Environments where every one can be used for a number of tests. Hence the present document defines testing
conditions that are common to several tests avoiding the need to duplicate the same information for every single test.
The present document defines default values for a variety of common areas. Where values are not specified in test
cases, the defaults in the present document will apply. If specified, the test case values will take precedence.
The present document addresses the FDD mode as well as the TDD mode.
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 34.108 version 14.3.0 Release 14 4 ETSI TS 134 108 V14.3.0 (2018-10)
1 Scope
The present document contains definitions of reference conditions and test signals, default parameters, reference radio
bearer configurations used in radio bearer interoperability testing, common radio bearer configurations for other test
purposes, common requirements for test equipment and generic set-up procedures for use in UE conformance tests.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including
a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same
Release as the present document unless the context in which the reference is made suggests a different Release is
relevant (information on the applicable release in a particular context can be found in e.g. test case title,
description or applicability, message description or content).
[1] to [48] (void)
[49] 3GPP TS 34.108 Release 15: "Common test environments for User Equipment (UE);
Conformance testing"
3 Definitions, abbreviations and symbols
Void
4 Common requirements of test equipment
The requirements of the present document are provided in 3GPP TS 34.108 Release 15 [49].
5 to 11 Void
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 34.108 version 14.3.0 Release 14 5 ETSI TS 134 108 V14.3.0 (2018-10)
Annex A to C (informative):
Void
ETSI
---------------------- Page: 6 ----------------------
3GPP TS 34.108 version 14.3.0 Release 14 6 ETSI TS 134 108 V14.3.0 (2018-10)
Annex D (informative):
Change history
ETSI
---------------------- Page: 7 ----------------------
3GPP TS 34.108 version 14.3.0 Release 14 7 ETSI TS 134 108 V14.3.0 (2018-10)
Meetin Doc-1st-Level CR Rev Subject Cat Version Version Doc-2nd-
g-1st- -Current -New Level
Level
TP-08 Approval of the specification 2.0.0 3.0.0
TP-09 TP-000131 001 RRC Message Contents: RLCSize C 3.0.1 3.1.0 T1-000190
TP-09 TP-000131 002 RRC Message Contents: RLCParam C 3.0.1 3.1.0 T1-000191
TP-09 TP-000131 003 RRC Message Contents: PCPreamble C 3.0.1 3.1.0 T1-000192
TP-09 TP-000131 004 RRC Message Contents: RBIdentity C 3.0.1 3.1.0 T1-000193
TP-09 TP-000131 005 RRC Message Contents: TrCHParam C 3.0.1 3.1.0 T1-000194
TP-09 TP-000131 006 RRC Message Contents: UECapability C 3.0.1 3.1.0 T1-000195
TP-09 TP-000131 007 RRC Message Contents: RBMapping C 3.0.1 3.1.0 T1-000196
TP-09 TP-000131 008 RRC Message Contents: PagingCause C 3.0.1 3.1.0 T1-000197
TP-09 TP-000131 009 RRC Message Contents: CipheringAndIntegrity C 3.0.1 3.1.0 T1-000198
TP-09 TP-000131 010 RRC Message Contents: RLCInfo C 3.0.1 3.1.0 T1-000199
TP-09 TP-000131 011 RRC Message Contents: CompressedMode C 3.0.1 3.1.0 T1-000200
TP-09 TP-000131 012 RRC Message Contents: SIB C 3.0.1 3.1.0 T1-000201
TP-09 TP-000131 013 RRC Message Contents: PhyCH D 3.0.1 3.1.0 T1-000202
TP-09 TP-000131 014 RRC Message Contents: Measurement C 3.0.1 3.1.0 T1-000203
TP-09 TP-000131 015 RRC Message Contents: TFCS C 3.0.1 3.1.0 T1-000204
TP-09 TP-000131 016 RRC Message Contents: DPCHFrameOffset C 3.0.1 3.1.0 T1-000205
TP-09 TP-000131 017 Test USIM Parameters F 3.0.1 3.1.0 T1-000215
TP-09 TP-000131 018 Correction to definition of the test algorithm for F 3.0.1 3.1.0 T1-000164
authentication (clause 8.1.2)
TP-09 TP-000131 019 Reference Radio Bearer Configurations F 3.0.1 3.1.0 T1-000212
TP-09 TP-000131 020 TDD Single mode F 3.0.1 3.1.0 T1-000220
TP-10 TP-000215 021 Common generic procedure for AS testing B 3.1.0 3.2.0 T1-000294
TP-10 TP-000215 022 Requirements for the system simulator for support of F 3.1.0 3.2.0 T1-000303
Tcell parameter
TP-10 TP-000215 023 Minimum Performance Levels F 3.1.0 3.2.0 T1-000306
TP-10 TP-000215 024 Downlink signal conditions and propagation conditions D 3.1.0 3.2.0 T1-000307
TP-10 TP-000215 025 Updating 34.108 v3.1.0 to TDD single mode F 3.1.0 3.2.0 T1-000281
TP-10 TP-000215 026 Application of integrity mode protection to signalling F 3.1.0 3.2.0 T1-000296
message by default
TP-10 TP-000215 027 Updates to the default message contents in clause 9 C 3.1.0 3.2.0 T1-000282
TP-10 TP-000215 028 Updates to System Information Block (SIB) and Master C 3.1.0 3.2.0 T1-000283
Information Block (MIB) messages
TP-10 TP-000215 029 Application of ciphering during conformance testing C 3.1.0 3.2.0 T1-000285
TP-10 TP-000215 030 Addition for System Information parameters (34.108 F 3.1.0 3.2.0 T1-000304
clause 6.1)
TP-10 TP-000215 031 Correction for Generic Setup Procedures (34.108 F 3.1.0 3.2.0 T1-000305
clause 7.2)
TP-11 TP-010018 032 Default radio conditions for multi-cell environment F 3.2.0 3.3.0 T1-010078
TP-11 TP-010018 033 Correction for Generic Setup Procedures (34.108 F 3.2.0 3.3.0 T1-010079
clause 7.2)
TP-11 TP-010018 034 Corrections for Test USIM Parameters(34.108 clause 8) F 3.2.0 3.3.0 T1-010080
TP-11 TP-010018 035 Correction of clause number in TS 34.108. D 3.2.0 3.3.0 T1-010081
TP-11 TP-010018 036 Update of authentication test algorithm C 3.2.0 3.3.0 T1-010082
TP-11 TP-010018 037 Updates to clause 9 of TS 34.108 v3.2.0 F 3.2.0 3.3.0 T1-010084
TP-11 TP-010018 038 Updating to TDD single mode F 3.2.0 3.3.0 T1-010088
TP-11 TP-010018 039 Simulated network environments for TDD mode (SIB) F 3.2.0 3.3.0 T1-010089
TP-12 TP-010118 040 Corrections to clause 6.10 FDD parameters F 3.3.0 3.4.0 T1-010205
TP-12 TP-010118 041 Corrections to clause 6.10 TDD parameters F 3.3.0 3.4.0 T1-010206
TP-12 TP-010118 042 Adding section for radio bearer configurations intended D 3.3.0 3.4.0 T1-010210
for functional testing
TP-12 TP-010118 043 Update of list of abbreviations D 3.3.0 3.4.0 T1-010211
TP-12 TP-010118 044 Updates to clause 6.1 and 9 F 3.3.0 3.4.0 T1-010212
TP-12 TP-010118 045 Updates to clause 7.4 F 3.3.0 3.4.0 T1-010213
TP-12 TP-010118 046 clause 6.1: System Information Blocks for TDD Mode F 3.3.0 3.4.0 T1-010214
TP-12 TP-010118 047 Editorial corrections and removal of a reference F 3.3.0 3.4.0 T1-010215
document
TP-13 TP-010215 048 Correction to reference F 3.4.0 3.5.0 T1-010275
TP-13 TP-010215 049 Editorial modification for References F 3.4.0 3.5.0 T1-010276
TP-13 TP-010215 050 Some corrections in clause 5 F 3.4.0 3.5.0 T1-010277
TP-13 TP-010215 051 Update to Scope Statement F 3.4.0 3.5.0 T1-010278
TP-13 TP-010215 052 Clause 6.10 Definition of RB configurations, TDD F 3.4.0 3.5.0 T1-010279
parameters
TP-13 TP-010215 053 Updates to clause 6.1, clause 7.4 and clause 9 F 3.4.0 3.5.0 T1-010280
TP-13 TP-010215 054 Clause 6.1: Default radio conditions for Signalling tests F 3.4.0 3.5.0 T1-010281
TP-13 TP-010215 055 Correction of Radio Bearer Configurations for FDD F 3.4.0 3.5.0 T1-010282
Mode
TP-13 TP-010215 056 Correction of Radio Bearer Configurations for TDD F 3.4.0 3.5.0 T1-010283
Mode
TP-13 TP-010215 057 Changes to Signalling Radio Bearer (SRB) numbering F 3.4.0 3.5.0 T1-010284
TP-13 TP-010215 058 Missing bearers in tables 6.10.2.1.1 and 6.10.3.1.1 F 3.4.0 3.5.0 T1-010285
ETSI
---------------------- Page: 8 ----------------------
3GPP TS 34.108 version 14.3.0 Release 14 8 ETSI TS 134 108 V14.3.0 (2018-10)
Meetin Doc-1st-Level CR Rev Subject Cat Version Version Doc-2nd-
g-1st- -Current -New Level
Level
TP-13 TP-010215 059 Correction of system information block 5 F 3.4.0 3.5.0 T1-010286
TP-13 TP-010215 060 Introducing of 1.28 Mcps TDD Mode in clauses 4, 5 and F 3.4.0 4.0.0 T1-010287
6
TP-13 TP-010215 061 Introduction of System Information Blocks for 1.28 F 3.4.0 4.0.0 T1-010288
Mcps TDD Mode
TP-13 TP-010215 062 Introduction of typical radio parameters for 1.28 F 3.4.0 4.0.0 T1-010289
McpsTDD
TP-13 TP-010215 063 Clause 6.11 RBs for RLC and PDCP testing F 3.4.0 3.5.0 T1-010290
TP-14 TP-010285 065 1 Correction to 6.1 Contents of System Information Blocks A 4.0.0 4.1.0 T1-010475
TP-14 TP-010285 067 1 Corrections to clause 6.1, 7.4 and 9 A 4.0.0 4.1.0 T1-010473
TP-14 TP-010258 069 Reference Radio Conditions A 4.0.0 4.1.0 T1-010461
TP-14 TP-010258 071 Modification of Test procedures for RF tests A 4.0.0 4.1.0 T1-010463
TP-14 TP-010258 073 Default message contents for RF tests A 4.0.0 4.1.0 T1-010465
TP-14 TP-010258 075 Correction to 6.10 Reference Radio Bearer A 4.0.0 4.1.0 T1-010467
configurations
TP-14 TP-010258 077 Definition of default value of rate matching attribute A 4.0.0 4.1.0 T1-010469
TP-14 TP-010258 079 Update of clause 7.4 and 6.10 A 4.0.0 4.1.0 T1-010471
TP-14 TP-010292 081 Correction on introduction of clause 6.10 A 4.0.0 4.1.0 --
TP-15 TP-020038 083 Replacement of Block STTD by Space Code Transmit A 4.1.0 4.2.0 T1-020092
Diversity (SCTD) (Rel-4)
TP-15 TP-020038 085 Update of reference radio conditions (Rel-4) A 4.1.0 4.2.0 T1-020098
TP-15 TP-020038 087 Update of system reference configurations and default A 4.1.0 4.2.0 T1-020100
messages (Rel-4)
TP-15 TP-020038 089 Corrections to 34108-410 A 4.1.0 4.2.0 T1-020102
TP-15 TP-020038 091 Introduction of new Reference RABs (Rel-4) A 4.1.0 4.2.0 T1-020195
TP-15 TP-020038 094 Update of SIBs for TDD (both modes) in TS 34.108 F 4.1.0 4.2.0 T1-020107
(Rel4)
TP-15 TP-020038 095 Clarification of bit rate of Interactive/Background PS A 4.1.0 4.2.0 T1-020184
RAB function (Rel-4)
Correction of CR implementation errors in clauses: 4.2.0 4.2.1
6.10.2.2 and 6.10.2.4.1.58.2.1.1
TP-16 TP-020141 108 Clause 7(reference) Update of generic setup F 4.2.1 4.3.0 T1-020289
procedures to use 13.6 kbps SRB in RRC connection
establishment TDD (3.84 Mcps and 1.28 Mcps)
TP-16 TP-020141 109 Correction to clause 7.3.3.4 RADIO BEARER SETUP A 4.2.1 4.3.0 T1-020291
message
TP-16 TP-020141 110 Change of RM attribute of DL:3.4 kbps SRBs for DCCH A 4.2.1 4.3.0 T1-020292
in for REL4
TP-16 TP-020141 111 New additional RAB configuration ( R1-020669) for A 4.2.1 4.3.0 T1-020293
REL4
TP-16 TP-020141 112 Correction of Puncturing Limit for RABs for REL4 A 4.2.1 4.3.0 T1-020294
TP-16 TP-020141 113 Test USIM A 4.2.1 4.3.0 T1-020295
TP-16 TP-020141 114 Clause 6.1 (SIBs) Rel-4 (3.84 Mcps and 1.28 Mcps F 4.2.1 4.3.0 T1-020296
TDD)
TP-16 TP-020141 115 Clause 6.10 References for TDD about Clarification of A 4.2.1 4.3.0 T1-020297
bit rate of Interactive/Background PS RAB
TP-16 TP-020141 116 Correction to default message in clause 9 for Rel4 A 4.2.1 4.3.0 T1-020298
TP-16 TP-020141 117 Correction to clause 6.1 for Rel4 A 4.2.1 4.3.0 T1-020299
TP-16 TP-020141 118 WCDMA1800 additions for Rel4 A 4.2.1 4.3.0 T1-020300
TP-16 TP-020141 119 Clause 9.1 Default message contents for TDD ( 3.84 F 4.2.1 4.3.0 T1-020301
Mcps and 1.28 Mcps) R4
TP-16 TP-020141 121 Update of generic setup procedures to use 13.6 kbps A 4.2.1 4.3.0 T1-020434
SRB in RRC connection establishment
TP-17 TP-020184 123 - Alignment of reference configurations on S-CCPCH with A 4.3.0 4.4.0 T1-020503
default system information messages
TP-17 TP-020184 125 - Addition of reference compressed mode pattern A 4.3.0 4.4.0 T1-020505
TP-17 TP-020184 127 - Corrections to default message contents as T1S- A 4.3.0 4.4.0 T1-020507
020347rev1
TP-17 TP-020184 129 - Additional default message contents for RF Testing A 4.3.0 4.4.0 T1-020509
TP-17 TP-020184 131 - Corrections related to SIB11, SIB12 and to the A 4.3.0 4.4.0 T1-020527
MEASUREMENT CONTROL message
TP-17 TP-020184 133 - Corrections to clause 6.1 (T1S-020349rev1) A 4.3.0 4.4.0 T1-020530
TP-17 TP-020184 135 - Introduction of reference configurations on S-CCPCH A 4.3.0 4.4.0 T1-020539
and PRACH with two interactive PS domain RABs
TP-17 TP-020184 137 - Removal of reference radio bearer configurations for A 4.3.0 4.4.0 T1-020541
unidirectional streaming CS RABa above 64 kbps
TP-17 TP-020184 140 - Some corrections and updates in clause 6.1 for TDD F 4.3.0 4.4.0 T1-020576
mode
TP-17 TP-020184 142 - Inclusion of default message contents for RF in clause F 4.3.0 4.4.0 T1-020578
9.2 for TDD mode
TP-18 TP-020293 144 - Correction to default messages in 9.1 and 9.2 A 4.4.0 4.5.0 T1-020658
ETSI
---------------------- Page: 9 ----------------------
3GPP TS 34.108 version 14.3.0 Release 14 9 ETSI TS 134 108 V14.3.0 (2018-10)
Meetin Doc-1st-Level CR Rev Subject Cat Version Version Doc-2nd-
g-1st- -Current -New Level
Level
TP-18 TP-020293 146 - Corrections in the TDD test frequencies according to A 4.4.0 4.5.0 T1-020674
core specs
TP-18 TP-020293 148 - Addition of alternative configuration using Turbo Coding A 4.4.0 4.5.0 T1-020694
for Interactive or background / UL:8 DL:8 kbps / PS RAB
+ UL:3.4 DL:3.4 kbps SRBs for DCCH
TP-18 TP-020293 150 - Correction to content of clause 6.10.2. A 4.4.0 4.5.0 T1-020709
TP-18 TP-020293 152 - Correction to SIB 11/12 definition A 4.4.0 4.5.0 T1-020712
TP-18 TP-020293 154 - Reference Measurement Channels A 4.4.0 4.5.0 T1-020768
TP-18 TP-020293 156 - Transferring system information definition using ASN.1 A 4.4.0 4.5.0 T1-020778
description to PRD
TP-18 TP-020293 158 - Correction to RLC RAB TFCS A 4.4.0 4.5.0 T1-020780
TP-18 TP-020293 160 - Default Message contents : Correction from CRs A 4.4.0 4.5.0 T1-020783
approved in RP17meeting
TP-18 TP-020293 162 - Corrections to SIB1 to SIB6 A 4.4.0 4.5.0 T1-020799
TP-18 TP-020293 164 - Correction to RAB configurations as revision of A 4.4.0 4.5.0 T1-020801
T1S020756
TP-18 TP-020293 166 - Parameter addition for Reference RABs based on LS A 4.4.0 4.5.0 T1-020803
from RAN2
TP-18 TP-020293 168 - Addition to clause 7.4 for multi call as T1S-020577rev2 A 4.4.0 4.5.0 T1-020818
(revision to T1S020820)
TP-18 TP-020293 169 - RAB Combinations for IMS Services F 4.4.0 4.5.0 T1-020819
TP-18 TP-020293 171 - Correction to Contents of the Scheduling Block System F 4.4.0 4.5.0 T1-020844
Information in clause 6.1.3.
TP-19 TP-030044 173 - RAB Removal from Rel-4 TS 34.108 as T1S030002rev1 A 4.5.0 4.6.0 T1-030037
TP-19 TP-030044 175 - Combine all Radio Bearer Setup messages into one A 4.5.0 4.6.0 T1-030040
table
TP-19 TP-030044 177 - Corrections to SB and SIB configurations in clause 6.1 A 4.5.0 4.6.0 T1-030042
as T1S030046rev1
TP-19 TP-030044 179 - Correction to TS 34.108 Rel-4 ; PAGING TYPE1 A 4.5.0 4.6.0 T1-030044
message (Packet in PS)
TP-19 TP-030044 181 - Clarification of authentication test algorithm and GSM A 4.5.0 4.6.0 T1-030046
cipher key
TP-19 TP-030044 183 - Addition of simulated network environment for inter-RAT A 4.5.0 4.6.0 T1-030048
test cases
TP-19 TP-030044 185 - Corrections to SIB1 to align with default values for LAC A 4.5.0 4.6.0 T1-030050
and RAC in 51.010-1.
TP-19 TP-030044 187 - Addition of default inter-RAT handover messages A 4.5.0 4.6.0 T1-030052
TP-19 TP-030044 189 - Correction of activation time IEs in default messages A 4.5.0 4.6.0 T1-030054
TP-19 TP-030044 191 - Correction to default SECURITY MODE COMMAND A 4.5.0 4.6.0 T1-030056
message
TP-19 TP-030044 193 - Addition of option for UL CM only in default reference A 4.5.0 4.6.0 T1-030058
CM patterns
TP-19 TP-030044 195 - Introduction of a reference RB configuration for RMC for A 4.5.0 4.6.0 T1-030060
BTFD tests (Rel4)
TP-19 TP-030044 197 - Update of the RRC connection request messages in A 4.5.0 4.6.0 T1-030063
34.108 Rel4
TP-19 TP-030043 198 - Introduction of Conversational PS RABs in Rel-4 TS F 4.5.0 4.6.0 T1-030107
34.108 as T1S030003rev1
TP-19 TP-030043 200 - Update of default parameters for 1 to 8 cell A 4.5.0 4.6.0 T1-030208
environments (TDD), clause 6.1.4, Rel-4
TP-19 TP-030043 202 - Update of Multi-cell environment for default radio A 4.5.0 4.6.0 T1-030210
conditions (TDD), clause 6.1.6 (Inclusion of cell 4), Rel-
4
TP-19 TP-030043 204 - Modification to Generic Registration Procedures A 4.5.0 4.6.0 T1-030222
TP-19 TP-030043 206 - Update of default configurations to enable testing of low A 4.5.0 4.6.0 T1-030228
end UE
TP-20 TP-030098 208 - Reinstate parameters for Interactive or background A 4.6.0 4.7.0 T1-030437
/UL:64 kbps / PS RAB
TP-20 TP-030098 210 - Correction to Figure 7.4.1.1 (Rel-4) A 4.6.0 4.7.0 T1-030483
TP-20 TP-030098 212 - Update of SIB 11 and 12 in clause 6.1.0b in TS 34.108 A 4.6.0 4.7.0 T1-030507
(TDD)
TP-20 TP-030098 214 - Update of Default parameters for 1 to 8 cell A 4.6.0 4.7.0 T1-030509
environments in TS 34.108 (TDD)
TP-20 TP-030098 216 - Correction of default messages according to 25331 A 4.6.0 4.7.0 T1-030632
CR1823
TP-20 TP-030098 218 - Clause 8.2: Definition of default values for A 4.6.0 4.7.0 T1-030644
authentication key K on test USIM
TP-20 TP-030098 219 - Update of Reconfiguration messages A 4.6.0 4.7.0 T1-030692
TP-20 TP-030098 221 - Correction to RADIO BEARER RELEASE and RRC A 4.6.0 4.7.0 T1-030699
CONNECTION SETUP messages (Revision of T1-
030569)
TP-20 TP-030140 226 - Correction to default SIB5 (FDD) A 4.6.0. 4.7.0 T1-030745
ETSI
---------------------- Page: 10 ----------------------
3GPP TS 34.108 version 14.3.0 Release 14 10 ETSI TS 134 108 V14.3.0 (2018-10)
Meetin Doc-1st-Level CR Rev Subject Cat Version Version Doc-2nd-
g-1st- -Current -New Level
Level
TP-21 TP-030191 228 - CR to 34.108, Rel-4, Clarification of seg_count in A 4.7.0 4.8.0 T1-030827
6.1.0a.3
TP-21 TP-030191 230 - General correction in clause 7.4 for Common generic A 4.7.0 4.8.0 T1-030976
procedures for AS testing
TP-21 TP-030191 233 - Incorrect activation time in CELL_FACH state . A 4.7.0 4.8.0 T1-031064
TP-21 TP-030191 235 - Incorrect Transport channel Parameters A 4.7.0 4.8.0 T1-031066
TP-21 TP-030191 237 - Corrections to TS 34.108 common procedures in clause A 4.7.0 4.8.0 T1-031095
7.4 of Rel-4 of TS 34.108
TP-21 TP-030191 239 - Removal of RLC AM in the Default Message Content A 4.7.0 4.8.0 T1-031151
TP-21 TP-030191 242 - CR 34.108 Rel-4: Manual attach in State 7 Registered A 4.7.0 4.8.0 T1-031175
Idle Mode on CS/PS
TP-21 TP-030191 244 - URA Identity in Cell Update Confirm and URA Update A 4.7.0 4.8.0 T1-031179
Confirm
TP-21 TP-030191 246 - CR to 34.108 R4; Correction to specification to reflect a A 4.7.0 4.8.0 T1-031241
change already approved in TTCN CR T1-030396
TP-21 TP-030191 248 - CR to 34.108 REL-4; Correction to clause 7.3 Test A 4.7.0 4.8.0 T1-031251
procedures for RF test
TP-21 TP-030191 240 - RB configuration for the support of wideband AMR F 4.7.0 4.8.0 T1-031154
speech telephony services
TP-22 TP-030279 251 1 Addition of Default message contents for TDD F 4.8.0 4.9.0 T1-031659
TP-22 TP-030279 252 1 Addition of Default message contents for TDD F 4.8.0 4.9.0 T1-031660
TP-22 TP-030279 253 1 Addition of Default message contents for TDD F 4.8.0 4.9.0 T1-031661
TP-22 TP-030279 254 1 Addition of Default message contents for TDD F 4.8.0 4.9.0 T1-031662
TP-22 TP-030279 255 1 Addition of Default message contents for TDD F 4.8.0 4.9.0 T1-031663
TP-22 TP-030279 256 1 Addition of Default message contents for TDD F 4.8.0 4.9.0 T1-031664
TP-22 TP-030279 257 1 Addition of Default message contents for TDD F 4.8.0 4.9.0 T1-031665
TP-22 TP-030279 258 1 Addition of Default message contents for TDD F 4.8.0 4.9.0 T1-031666
TP-22 TP-030279 260 2 CR on PAGING TYPE 1, RRC CONNECTION A 4.8.0 4.9.0 T1-031596
REQUEST and RRC CONNECTION SETUP messages
for MT RR Connection
TP-22 TP-030279 262 CR 34.108 Rel-4: EFRPLMNACT (RPLMN Last used A 4.8.0 4.9.0 T1-031381
Access Technology) removed
TP-22 TP-030279 264 1 Update of default messages for RRC CONNECTION A 4.8.0 4.9.0 T1-031547
SETUP and SECURITY MODE COMMAND
TP-22 TP-030279 266 1 Description and corrections of channels for minimum F 4.8.0 4.9.0 T1-031645
performance levels, TDD mode.
TP-22 TP-030279 268 1 Test frequencies of UMTS800MHz band VI A 4.8.0 4.9.0 T1-031555
TP-22 TP-030279 269 CR 34.108 Rel-4: Addition of Bearer combination for F 4.8.0 4.9.0 T1-031441
Interactive/background UL 64 kbps DL 768 kbps for Rel-
5
TP-22 TP-030279 271 1 Update of generic test procedure for TX, RX and A 4.8.0 4.9.0 T1-031610
Performance Requirement
TP-22 TP-030279 273 1 Introduction of generic test procedure for RRM A 4.8.0 4.9.0 T1-031608
handover test cases
TP-22 TP-030279 275 1 Correction of CM TGD parameter A 4.8.0 4.9.0 T1-031591
TP-22 TP-030279 277 1 Corrections to default message contents of Radio F 4.8.0 4.9.0 T1-031594
Bearer Release
TP-22 TP-030279 279 1 Modification to default DPCCH_Power_offset value A 4.8.0 4.9.0 T1-031598
TP-22 TP-030279 283 Correction of TFCS for radio bearer combination A 4.8.0 4.9.0 T1-031527
6.10.2.4.1.51b
TP-23 TP-040037 284 - New Radio Bearer Setup (FDD) message for RF F 4.9.0 4.10.0 T1-040417
(Revision of T1-040258)
TP-23 TP-040037 287 - Corrections to default message contents of RRC A 4.9.0 4.10.0 T1-040080
Connection Setup message -> 2nd change not
implemented (not implementable)
TP-23 TP-040037 289 - Correction to Default parameters for Cells 1 to 8 in A 4.9.0 4.10.0 T1-040095
MultiPLMN cell environments - Rel-4
TP-23 TP-040037 291 - Corrections to TDD HCR RABs A 4.9.0 4.10.0 T1-040103
TP-23 TP-040037 296 - LCR Corrections to TDD RABs merge of T1-040104 , F 4.9.0 4.10.0 T1-040299
T1-040201 and T1-040203
TP-23 TP-040037 298 - Correction to handling of Entered Parameter IE in A 4.9.0 4.10.0 T1-040411
default contents for Initial Direct Transfer
TP-23 TP-040037 300 - The diverse operation in TDD mode updating according A 4.9.0 4.10.0 T1-040368
to the core specification
TP-23 TP-040037 302 - correction of measurement control default message F 4.9.0 4.10.0 T1-040370
contents for TDD -> Not implemented (not
implementable)
TP-23 TP-040037 303 - correction of RADIO BEARER SETUP default message F 4.9.0 4.10.0 T1-040371
contents for 1.28 Mcps TDD
TP-23 TP-040037 304 - Correction of RADIO BEARER RELEASE default F 4.9.0 4.10.0 T1-040372
message contents for TDD: AM or UM (1.28 Mcps TDD)
ETSI
---------------------- Page: 11 ----------------------
3GPP TS 34.108 version 14.3.0 Release 14 11 ETSI TS 134 108 V14.3.0 (2018-10)
Meetin Doc-1st-Level CR Rev Subject Cat Version Version Doc-2nd-
g-1st- -Current -New Level
Level
TP-23 TP-040037 305 - Contents of RRC CONNECTION SETUP message: UM F 4.9.0 4.10.0 T1-040373
(Transition to CELL_DCH) (1.28 Mcps TDD) -> Not
implemented (not implementable)
TP-23 TP-040037 292 - New I/B UL:64 DL:768 kbps PS RAB misplaced F 4.10.0 5.0.0 T1-040109
TP-23 TP-040037 294 - Generic setup procedure and default message contents F 4.10.0 5.0.0 T1-040271
for HSDPA (as of T1-040069rev1)
TP-23 TP-040037 295 - Baseline radio bearer
...