|
TECHNICAL SPECIFICATION
Universal Mobile Telecommunications System (UMTS);
User Equipment (UE) conformance specification;
Radio transmission and reception (FDD);
Part 1: Conformance specification
(3GPP TS 34.121-1 version 15.1.0 Release 15)
---------------------- Page: 1 ----------------------
3GPP TS 34.121-1 version 15.1.0 Release 15 1 ETSI TS 134 121-1 V15.1.0 (2018-10)
Reference
RTS/TSGR-0534121-1vf10
Keywords
UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 34.121-1 version 15.1.0 Release 15 2 ETSI TS 134 121-1 V15.1.0 (2018-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
rd
This Technical Specification (TS) has been produced by the ETSI 3 Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 34.121-1 version 15.1.0 Release 15 3 ETSI TS 134 121-1 V15.1.0 (2018-10)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 59
Introduction . 59
1 Scope . 60
2 References . 60
3 Definitions, symbols, abbreviations and equations . 62
3.1 Definitions . 62
3.2 Symbols . 63
3.3 Abbreviations . 63
3.4 Equations . 64
4 Frequency bands and channel arrangement . 66
4.1 General . 66
4.2 Frequency bands . 67
4.3 TX-RX frequency separation . 68
4.4 Channel arrangement . 68
4.4.1 Channel spacing . 68
4.4.2 Channel raster . 69
4.4.3 Channel number . 69
4.4.4 UARFCN . 71
4A Reference Conditions . 72
4A.1 Generic setup procedures . 72
4A.2 System information . 72
4A.3 Message contents . 72
4A.4 Measurement configurations . 73
5 Transmitter Characteristics . 73
5.1 General . 73
5.2 Maximum Output Power . 74
5.2.1 Definition and applicability . 74
5.2.2 Minimum Requirements . 75
5.2.3 Test purpose . 76
5.2.4 Method of test . 76
5.2.4.1 Initial conditions . 76
5.2.4.2 Procedure . 77
5.2.5 Test requirements . 77
5.2A Maximum Output Power with HS-DPCCH (Release 5 only) . 78
5.2A.1 Definition and applicability . 78
5.2A.2 Minimum Requirements . 78
5.2A.3 Test purpose . 78
5.2A.4 Method of test . 78
5.2A.4.1 Initial conditions . 78
5.2A.4.2 Procedure . 79
5.2A.5 Test requirements . 79
5.2AA Maximum Output Power with HS-DPCCH (Release 6 and later) . 80
5.2AA.1 Definition and applicability . 80
5.2AA.2 Minimum Requirements . 80
5.2AA.3 Test purpose . 80
5.2AA.4 Method of test . 80
5.2AA.4.1 Initial conditions . 80
5.2AA.4.2 Procedure . 81
5.2AA.5 Test requirements . 81
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 34.121-1 version 15.1.0 Release 15 4 ETSI TS 134 121-1 V15.1.0 (2018-10)
5.2AB Maximum Output Power for OLTD . 82
5.2AB.1 Definition and applicability . 82
5.2AB.2 Minimum Requirements . 83
5.2AB.3 Test purpose . 83
5.2AB.4 Method of test . 83
5.2AB.4.1 Initial conditions . 83
5.2AB.4.2 Procedure . 84
5.2AB.5 Test requirements . 84
5.2AC Maximum Output Power for UL CLTD activation state 1 . 86
5.2AC.1 Definition and applicability . 86
5.2AC.2 Minimum Requirements . 86
5.2AC.3 Test purpose . 87
5.2AC.4 Method of test . 87
5.2AC.4.1 Initial conditions . 87
5.2AC.4.2 Procedure . 87
5.2AC.5 Test requirements . 88
5.2AD Maximum Output Power for UL CLTD activation state 2 and 3 . 89
5.2AD.1 Definition and applicability . 89
5.2AD.2 Minimum Requirements . 89
5.2AD.3 Test purpose . 90
5.2AD.4 Method of test . 90
5.2AD.4.1 Initial conditions . 90
5.2AD.4.2 Procedure . 91
5.2AD.5 Test requirements . 91
5.2B Maximum Output Power with HS-DPCCH and E-DCH. 92
5.2B.1 Definition and applicability . 92
5.2B.2 Minimum Requirements . 92
5.2B.3 Test purpose . 93
5.2B.4 Method of test . 93
5.2B.4.1 Initial conditions . 93
5.2B.4.2 Procedure . 95
5.2B.5 Test requirements . 95
5.2BA UE Maximum Output Power for DC-HSUPA (QPSK). 97
5.2BA.1 Definition and applicability . 97
5.2BA.2 Minimum Requirements . 97
5.2BA.3 Test purpose . 98
5.2BA.4 Method of test . 98
5.2BA.4.1 Initial conditions . 98
5.2BA.4.2 Procedure . 99
5.2BA.5 Test requirements . 99
5.2BB UE Maximum Output Power for DC-HSUPA (16QAM) . 100
5.2BB.1 Definition and applicability . 100
5.2BB.2 Minimum Requirements . 101
5.2BB.3 Test purpose . 102
5.2BB.4 Method of test . 102
5.2BB.4.1 Initial conditions . 102
5.2BB.4.2 Procedure . 102
5.2BB.5 Test requirements . 103
5.2BC Maximum Output Power with HS-DPCCH and E-DCH for OLTD . 104
5.2BC.1 Definition and applicability . 104
5.2BC.2 Minimum Requirements . 104
5.2BC.3 Test purpose . 104
5.2BC.4 Method of test . 105
5.2BC.4.1 Initial conditions . 105
5.2BC.4.2 Procedure . 107
5.2BC.4.2.1 Procedure for sub-test 1 to 4 . 107
5.2BC.5 Test requirements . 107
5.2BD Maximum Output Power with HS-DPCCH and E-DCH for UL CLTD activation state 1 . 108
5.2BD.1 Definition and applicability . 108
5.2BD.2 Minimum Requirements . 109
5.2BD.3 Test purpose . 109
5.2BD.4 Method of test . 109
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 34.121-1 version 15.1.0 Release 15 5 ETSI TS 134 121-1 V15.1.0 (2018-10)
5.2BD.4.1 Initial conditions . 109
5.2BD.4.2 Procedure . 111
5.2BD.4.2.1 Procedure for sub-test 1 to 4 . 111
5.2BD.5 Test requirements . 112
5.2BE Maximum Output Power with HS-DPCCH and E-DCH for UL CLTD activation state 2 and 3. . 113
5.2BE.1 Definition and applicability . 113
5.2BE.2 Minimum Requirements . 113
5.2BE.3 Test purpose . 114
5.2BE.4 Method of test . 114
5.2BE.4.1 Initial conditions . 114
5.2BE.4.2 Procedure . 116
5.2BE.4.2.1 Procedure for sub-test 1 to 4 . 116
5.2BE.5 Test requirements . 116
5.2C UE relative code domain power accuracy . 118
5.2C.1 Definition and applicability . 118
5.2C.2 Minimum Requirements . 118
5.2C.3 Test purpose . 118
5.2C.4 Method of test . 118
5.2C.4.1 Initial conditions . 118
5.2C.4.2 Procedure . 119
5.2C.5 Test requirements . 120
5.2CA UE relative code domain power accuracy for OLTD . 121
5.2CA.1 Definition and applicability . 121
5.2CA.2 Minimum Requirements . 121
5.2CA.3 Test purpose . 121
5.2CA.4 Method of test . 121
5.2CA.4.1 Initial conditions . 121
5.2CA.4.2 Procedure . 122
5.2CA.5 Test requirements . 123
5.2CB UE relative code domain power accuracy for UL CLTD activation state 1 . 124
5.2CB.1 Definition and applicability . 124
5.2CB.2 Minimum Requirements . 124
5.2CB.3 Test purpose . 124
5.2CB.4 Method of test . 124
5.2CB.4.1 Initial conditions . 124
5.2CB.4.2 Procedure . 125
5.2CB.5 Test requirements . 126
5.2CC UE relative code domain power accuracy for UL CLTD activation state 2 and 3 . 127
5.2CC.1 Definition and applicability .
...