|
TECHNICAL SPECIFICATION
Universal Mobile Telecommunications System (UMTS);
LTE;
Active Antenna System (AAS) Base Station (BS)
conformance testing;
Part 2: radiated conformance testing
(3GPP TS 37.145-2 version 14.6.0 Release 14)
---------------------- Page: 1 ----------------------
3GPP TS 37.145-2 version 14.6.0 Release 14 1 ETSI TS 137 145-2 V14.6.0 (2018-10)
Reference
RTS/TSGR-0437145-2ve60
Keywords
LTE,UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 37.145-2 version 14.6.0 Release 14 2 ETSI TS 137 145-2 V14.6.0 (2018-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 37.145-2 version 14.6.0 Release 14 3 ETSI TS 137 145-2 V14.6.0 (2018-10)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 6
1 Scope . 7
2 References . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 10
3.3 Abbreviations . 12
4 General test conditions and declarations . 13
4.1 Measurement uncertainties and test requirements . 13
4.1.1 General . 13
4.1.2 Acceptable uncertainty of Test System . 13
4.1.2.1 General . 13
4.1.2.2 Measurement of transmitter . 13
4.1.2.3 Measurement of receiver . 13
4.1.3 Interpretation of measurement results . 13
4.2 Conducted and radiated requirement reference points . 14
4.3 Base station classes for AAS BS . 15
4.4 Regional requirements . 15
4.5 Operating bands and band categories . 15
4.6 Channel arrangements . 15
4.7 Requirements for AAS BS capable of multi-band operation . 15
4.8 AAS BS configurations . 15
4.8.1 Transmit configurations . 15
4.8.2 Receive configurations . 16
4.8.3 Power supply options . 16
4.8.4 BS with integrated Iuant BS modem . 16
4.9 Capability sets . 16
4.10 Manufacturer declarations . 17
4.11 Test signal configurations for testing . 20
4.11.1 General . 20
4.11.2 Test signal configurations . 20
4.11.2.1 ATCR1: UTRA multicarrier operation . 20
4.11.2.1.1 General . 20
4.11.2.1.2 ATCR1a generation . 21
4.11.2.1.3 ATCR1b generation . 21
4.11.2.1.4 ATCR1 EIRP allocation . 21
4.11.2.2 ANTCR1: UTRA FDD multicarrier non-contiguous operation . 21
4.11.2.2.1 General . 21
4.11.2.2.2 ANTCR1 generation . 21
4.11.2.2.3 ANTCR1 EIRP allocation . 22
4.11.2.3 ATCR2: E-UTRA multicarrier operation . 22
4.11.2.3.1 General . 22
4.11.2.3.2 ATCR2a generation . 22
4.11.2.3.3 ATCR2b generation . 22
4.11.2.3.4 ATCR2 EIRP allocation . 23
4.11.2.4 ANTCR2: E-UTRA multicarrier non-contiguous operation . 23
4.11.2.4.1 General . 23
4.11.2.4.2 ANTCR2 generation . 23
4.11.2.4.3 ANTCR2 EIRP allocation . 23
4.11.2.5 ATCR3: UTRA and E-UTRA multi RAT operation . 23
4.11.2.5.1 General . 23
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 37.145-2 version 14.6.0 Release 14 4 ETSI TS 137 145-2 V14.6.0 (2018-10)
4.11.2.5.2 ATCR3a generation . 24
4.11.2.5.3 ATCR3b generation . 24
4.11.2.5.4 ATCR3 EIRP allocation . 24
4.11.2.6 ANTCR3: UTRA and E-UTRA multi RAT non-contiguous operation . 24
4.11.2.6.1 General . 24
4.11.2.6.2 ANTCR3a generation . 25
4.11.2.6.3 ANTCR3 EIRP allocation . 25
4.11.2.7 ATCR4: Single carrier for receiver tests . 25
4.11.2.7.1 ATCR4a generation . 25
4.11.2.7.2 ATCR4b generation . 25
4.11.2.7.3 ATCR4c generation . 25
4.11.2.7.4 ATCR4 EIRP allocation . 26
4.11.2.8 Generation of MB-MSR test configurations . 26
4.11.2.8.1 ATCR5a: MB-MSR test configuration for full carrier allocation . 26
4.11.2.8.2 ATCR5b: MB-MSR test configuration with high PSD per carrier . 27
4.11.2.9 ATCR6: Single carrier for Transmitter tests . 28
4.11.2.9.1 ATCR6a generation . 28
4.11.2.9.2 ATCR6b generation . 28
4.11.2.9.3 ATCR6c generation . 28
4.11.2.9.4 ATCR6 EIRP allocation . 28
4.12 RF channels and test models . 28
4.12.1 RF channels . 28
4.12.2 Test models . 29
4.13 Format and interpretation of tests . 29
4.14 Reference coordinate system . 30
5 Applicability of Requirements . 31
5.1 General . 31
5.2 Test configurations for AAS BS for operating bands where MSR with more than 1 RAT is supported . 32
5.3 Test configurations for multi-carrier capable AAS BS in operating bands where one RAT capability sets
are supported . 32
5.3.1 General . 32
5.3.2 AAS BS supporting one RAT only MSR in the operating band . 33
5.3.3 AAS BS supporting Single-RAT UTRA in the operating band . 33
5.3.4 AAS BS supporting Single-RAT E-UTRA in the operating band . 34
5.4 Test configurations for AAS BS operating bands with multi-band dependencies. 34
5.4.1 AAS BS operating bands with multi-band dependencies supporting MSR operation . 34
5.4.2 AAS BS operating bands with multi-band dependencies supporting Single-RAT only . 34
6 Radiated transmitter characteristics . 35
6.1 General . 35
6.2 Radiated Transmit Power . 35
6.2.1 Definition and applicability . 35
6.2.2 Minimum Requirement . 35
6.2.3 Test purpose . 36
6.2.4 Method of test . 36
6.2.4.1 Initial conditions . 36
6.2.4.2 Procedure . 36
6.2.5 Test Requirement . 36
7 Radiated receiver characteristics . 37
7.1 General . 37
7.2 OTA sensitivity . 37
7.2.1 Definition and applicability . 37
7.2.2 Minimum Requirement . 38
7.2.3 Test Purpose. 38
7.2.4 Method of test . 38
7.2.4.1 Initial conditions . 38
7.2.4.2 Procedure . 38
7.2.5 Test Requirements . 39
7.2.5.1 General . 39
7.2.5.2 UTRA FDD Test Requirements . 39
7.2.5.3 UTRA TDD 1,28Mcp option Test Requirements . 39
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 37.145-2 version 14.6.0 Release 14 5 ETSI TS 137 145-2 V14.6.0 (2018-10)
7.2.5.4 E-UTRA Test Requirements . 39
Annex A (normative): Test system characterization . 41
Annex B (normative): Calibration . 42
Annex C (informative): Test tolerances and derivation of test requirements . 43
C.1 General . 43
C.2 Measurement of transmitter (OTA) . 43
C.3 Measurement of receiver (OTA) . 43
Annex D (informative): Test system set-up . 44
D.1 Transmitter . 44
D1.1 Radiated Transmit Power . 44
D.2 Receiver . 45
D.2.1 OTA sensitivity . 45
Annex E (normative): Estimation of Measurement Uncertainty . 46
E.1 General . 46
E.2 Measurement methodology descriptions . 46
E.3 Measurement uncertainty budget format . 46
E.4 Measurement uncertainty budgets . 46
E.5 Measurement error contribution descriptions . 46
Annex F (informative): Change history . 47
History . 48
ETSI
---------------------- Page: 6 ----------------------
3GPP TS 37.145-2 version 14.6.0 Release 14 6 ETSI TS 137 145-2 V14.6.0 (2018-10)
Foreword
rd
This Technical Specification has been produced by the 3 Generation Partnership Project (3GPP).
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z the third digit is incremented when editorial only changes have been incorporated in the document.
ETSI
---------------------- Page: 7 ----------------------
3GPP TS 37.145-2 version 14.6.0 Release 14 7 ETSI TS 137 145-2 V14.6.0 (2018-10)
1 Scope
The present document specifies radiated test methods and conformance requirements for single RAT E-UTRA operation,
single RAT UTRA operation (FDD and TDD) and Multi-Standard Radio (MSR) UTRA and E-UTRA Active Antenna
System (AAS) Base Station (BS). These have been derived from, and are consistent with non-AAS BS specifications in
3GPP TS 25.104 [2], 3GPP TS 25.105 [3], 3GPP TS 36.104 [4] or 3GPP TS 37.104 [5]. The technical specification
3GPP TS 37.145 is in 2 parts, part 3GPP TS 37.145-1 [9] covers conducted requirements and part 3GPP TS 37.145-2
(the present document) covers radiated requirements.
The present document does not establish radiated test methods and conformance requirements for Band 46 operation as
it is not supported by AAS BS. Conducted Band 46 test requirements are still applicable for AAS BS for protection of
and against Band 46 operation, as specified in 3GPP TS 37.145-1 [9].
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
- References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
- For a specific reference, subsequent revisions do not apply.
- For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including
a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same
Release as the present document.
[1] 3GPP TR 21.905: "Vocabulary for 3GPP Specifications".
[2] 3GPP TS 25.104: "Base Station (BS) radio transmission and reception (FDD)".
[3] 3GPP TS 25.105: "Base Station (BS) radio transmission and reception (TDD)".
[4] 3GPP TS 36.104: "Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS)
radio transmission and reception".
[5] 3GPP TS 37.104: "E-UTRA, UTRA and GSM/EDGE; Multi-Standard Radio (MSR) Base Station
(BS) radio transmission and reception".
[6] 3GPP TS 37.105: "Active Antenna System (AAS) Base Station (BS) transmission and reception".
[7] 3GPP TR 37.842: "E-UTRA and UTRA; Radio Frequency (RF) requirement background for
Active Antenna System (AAS) Base Station (BS)".
[8] Recommendation ITU-R M.1545: "Measurement uncertainty as it applies to test limits for the
terrestrial component of International Mobile Telecommunications-2000".
[9] 3GPP TS 37.145-1: "Active Antenna System (AAS) Base Station (BS) conformance testing;
Part 1: Conducted conformance testing".
[10] 3GPP TS 25.141: "Base Station (BS) conformance testing (FDD)".
[11] 3GPP TS 25.142: "Base Station (BS) conformance testing (TDD)".
[12] 3GPP TS 36.141: "Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS)
conformance testing".
[13] 3GPP TS 37.141: "E-UTRA, UTRA and GSM/EDGE; Multi-Standard Radio (MSR) Base Station
(BS) conformance testing".
ETSI
----------------------
...