|
TECHNICAL SPECIFICATION
LTE;
Evolved Universal Terrestrial Radio Access (E-UTRA);
User Equipment (UE) radio transmission and reception
(3GPP TS 36.101 version 10.28.0 Release 10)
---------------------- Page: 1 ----------------------
3GPP TS 36.101 version 10.28.0 Release 10 1 ETSI TS 136 101 V10.28.0 (2019-01)
Reference
RTS/TSGR-0436101vas0
Keywords
LTE
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 36.101 version 10.28.0 Release 10 2 ETSI TS 136 101 V10.28.0 (2019-01)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
rd
This Technical Specification (TS) has been produced by the ETSI 3 Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 36.101 version 10.28.0 Release 10 3 ETSI TS 136 101 V10.28.0 (2019-01)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 13
1 Scope . 14
2 References . 14
3 Definitions, symbols and abbreviations . 14
3.1 Definitions . 14
3.2 Symbols . 15
3.3 Abbreviations . 17
4 General . 18
4.1 Relationship between minimum requirements and test requirements . 18
4.2 Applicability of minimum requirements . 18
4.3 Void . 18
4.3A Applicability of minimum requirements (CA, UL-MIMO) . 18
4.4 RF requirements in later releases . 19
5 Operating bands and channel arrangement . 19
5.1 General . 19
5.2 Void . 19
5.3 Void . 19
5.4 Void . 19
5.5 Operating bands . 19
5.5A Operating bands for CA . 20
5.5B Operating bands for UL-MIMO . 21
5.6 Channel bandwidth . 21
5.6.1 Channel bandwidths per operating band . 22
5.6A Channel bandwidth for CA . 23
5.6A.1 Channel bandwidths per operating band for CA . 25
5.6B Channel bandwidth for UL-MIMO . 26
5.6B.1 Void . 26
5.7 Channel arrangement . 26
5.7.1 Channel spacing . 26
5.7.1A Channel spacing for CA . 26
5.7.2 Channel raster . 26
5.7.2A Channel raster for CA . 27
5.7.3 Carrier frequency and EARFCN . 27
5.7.4 TX–RX frequency separation . 28
5.7.4A TX–RX frequency separation for CA . 29
6 Transmitter characteristics . 29
6.1 General . 29
6.2 Transmit power . 29
6.2.1 Void . 29
6.2.2 UE maximum output power . 29
6.2.2A UE maximum output power for CA . 30
6.2.2B UE maximum output power for UL-MIMO . 31
6.2.3 UE maximum output power for modulation / channel bandwidth . 32
6.2.3A UE Maximum Output power for modulation / channel bandwidth for CA . 33
6.2.3B UE maximum output power for modulation / channel bandwidth for UL-MIMO . 34
6.2.4 UE maximum output power with additional requirements . 34
6.2.4A UE maximum output power with additional requirements for CA . 39
6.2.4A.1 A-MPR for CA_NS_01 for CA_1C . 40
6.2.4A.2 A-MPR for CA_NS_02 for CA_1C . 41
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 36.101 version 10.28.0 Release 10 4 ETSI TS 136 101 V10.28.0 (2019-01)
6.2.4A.3 A-MPR for CA_NS_03 for CA_1C . 41
6.2.4B UE maximum output power with additional requirements for UL-MIMO . 42
6.2.5 Configured transmitted power . 42
6.2.5A Configured transmitted power for CA . 44
6.2.5B Configured transmitted power for UL-MIMO . 45
6.3 Output power dynamics . 46
6.3.1 (Void) . 46
6.3.2 Minimum output power . 46
6.3.2.1 Minimum requirement . 46
6.3.2A UE Minimum output power for CA . 46
6.3.2A.1 Minimum requirement for CA . 46
6.3.2B UE Minimum output power for UL-MIMO . 47
6.3.2B.1 Minimum requirement . 47
6.3.3 Transmit OFF power . 47
6.3.3.1. Minimum requirement . 47
6.3.3A UE Transmit OFF power for CA . 48
6.3.3A.1 Minimum requirement for CA . 48
6.3.3B UE Transmit OFF power for UL-MIMO . 48
6.3.3B.1 Minimum requirement . 48
6.3.4 ON/OFF time mask . 48
6.3.4.1 General ON/OFF time mask . 48
6.3.4.2 PRACH and SRS time mask . 49
6.3.4.2.1 PRACH time mask . 49
6.3.4.2.2 SRS time mask . 49
6.3.4.3 Slot / Sub frame boundary time mask . 50
6.3.4.4 PUCCH / PUSCH / SRS time mask . 51
6.3.4A ON/OFF time mask for CA . 52
6.3.4B ON/OFF time mask for UL-MIMO . 52
6.3.5 Power Control . 52
6.3.5.1 Absolute power tolerance . 52
6.3.5.1.1 Minimum requirements . 53
6.3.5.2 Relative Power tolerance . 53
6.3.5.2.1 Minimum requirements . 53
6.3.5.3 Aggregate power control tolerance . 54
6.3.5.3.1 Minimum requirement . 54
6.3.5A Power control for CA . 55
6.3.5A.1 Absolute power tolerance . 55
6.3.5A.1.1 Minimum requirements . 55
6.3.5A.2 Relative power tolerance . 55
6.3.5A.2.1 Minimum requirements . 55
6.3.5A.3 Aggregate power control tolerance . 55
6.3.5A.3.1 Minimum requirements . 56
6.3.5B Power control for UL-MIMO . 56
6.4 Void . 56
6.5 Transmit signal quality . 56
6.5.1 Frequency error . 56
6.5.1A Frequency error for CA . 56
6.5.1B Frequency error for UL-MIMO . 56
6.5.2 Transmit modulation quality . 56
6.5.2.1 Error Vector Magnitude . 57
6.5.2.1.1 Minimum requirement . 57
6.5.2.2 Carrier leakage . 57
6.5.2.2.1 Minimum requirements . 57
6.5.2.3 In-band emissions . 58
6.5.2.3.1 Minimum requirements . 58
6.5.2.4 EVM equalizer spectrum flatness . 58
6.5.2.4.1 Minimum requirements . 59
6.5.2A Transmit modulation quality for CA . 60
6.5.2A.1 Error Vector Magnitude . 60
6.5.2A.2 Carrier leakage for CA . 60
6.5.2A.2.1 Minimum requirements . 60
6.5.2A.3 In-band emissions . 60
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 36.101 version 10.28.0 Release 10 5 ETSI TS 136 101 V10.28.0 (2019-01)
6.5.2A.3.1 Minimum requirement for CA . 60
6.5.2B Transmit modulation quality for UL-MIMO . 62
6.5.2B.1 Error Vector Magnitude . 63
6.5.2B.2 Carrier leakage . 63
6.5.2B.3 In-band emissions . 63
6.5.2B.4 EVM equalizer spectrum flatness for UL-MIMO . 63
6.6 Output RF spectrum emissions . 63
6.6.1 Occupied bandwidth . 64
6.6.1A Occupied bandwidth for CA . 64
6.6.1B Occupied bandwidth for UL-MIMO . 64
6.6.2 Out of band emission . 64
6.6.2.1 Spectrum emission mask . 64
6.6.2.1.1 Minimum requirement . 65
6.6.2.1A Spectrum emission mask for CA . 65
6.6.2.2 Additional spectrum emission mask . 65
6.6.2.2.1 Minimum requirement (network signalled value "NS_03", “NS_11”, and “NS_20”) . 65
6.6.2.2.2 Minimum requirement (network signalled value "NS_04") . 66
6.6.2.2.3 Minimum requirement (network signalled value "NS_06" or “NS_07”) . 66
6.6.2.3 Adjacent Channel Leakage Ratio . 67
6.6.2.3.1 Minimum requirement E-UTRA . 67
6.6.2.3.1A Void . 68
6.6.2.3.2 Minimum requirements UTRA . 68
6.6.2.3.2A Minimum requirement UTRA for CA . 69
6.6.2.3.3A Minimum requirements for CA E-UTRA . 69
6.6.2.4 Void. 70
6.6.2.4.1 Void . 70
6.6.2A Void . 70
6.6.2B Out of band emission for UL-MIMO . 70
6.6.3 Spurious emissions . 70
6.6.3.1 Minimum requirements . 70
6.6.3.1A Minimum requirements for CA . 71
6.6.3.2 Spurious emission band UE co-existence . 71
6.6.3.2A Spurious emission band UE co-existence for CA . 74
6.6.3.3 Additional spurious emissions . 75
6.6.3.3.1 Minimum requirement (network signalled value "NS_05") . 75
6.6.3.3.2 Minimum requirement (network signalled value “NS_07”) . 76
6.6.3.3.3 Minimum requirement (network signalled value “NS_08”) . 76
6.6.3.3.4 Minimum requirement (network signalled value “NS_09”) . 77
6.6.3.3.5 Void . 77
6.6.3.3.6 Void . 77
6.6.3.3.7 Void . 77
6.6.3.3.8 Void . 77
6.6.3.3.9 Void . 77
6.6.3.3.10 Void . 77
6.6.3.3.11 Void . 77
6.6.3.3.12 Void .
...