ETSI EN 319 522-4-1 V1.2.1 (2019-01)

Electronic Signatures and Infrastructures (ESI); Electronic Registered Delivery Services; Part 4: Bindings; Sub-part 1: Message delivery bindings

ETSI EN 319 522-4-1 V1.2.1 (2019-01)

Name:ETSI EN 319 522-4-1 V1.2.1 (2019-01)   Standard name:Electronic Signatures and Infrastructures (ESI); Electronic Registered Delivery Services; Part 4: Bindings; Sub-part 1: Message delivery bindings
Standard number:ETSI EN 319 522-4-1 V1.2.1 (2019-01)   language:English language
Release Date:27-Jan-2019   technical committee:ESI - Electronic Signatures and Infrastructures
Drafting committee:   ICS number:
ETSI EN 319 522-4-1 V1.2.1 (2019-01)






EUROPEAN STANDARD
Electronic Signatures and Infrastructures (ESI);
Electronic Registered Delivery Services;
Part 4: Bindings;
Sub-part 1: Message delivery bindings

---------------------- Page: 1 ----------------------
2 ETSI EN 319 522-4-1 V1.2.1 (2019-01)



Reference
REN/ESI-0019522-4-1v121
Keywords
e-delivery services, registered e-delivery
services, registered electronic mail

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at

If you find errors in the present document, please send your comment to one of the following services:

Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.

GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 319 522-4-1 V1.2.1 (2019-01)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definition of terms and abbreviations . 6
3.1 Terms . 6
3.2 Abbreviations . 6
4 Message delivery bindings - general concepts . 6
5 AS4 binding . 6
5.1 Introduction . 6
5.2 Generic requirements . 7
5.3 Signing and encryption of the AS4 message . 8
5.4 Binding of ERD dispatch . 8
5.5 Binding of ERDS receipt . 8
5.6 Binding of ERDS serviceInfo . 8
5.7 Binding of ERD payload . 9
6 IETF RFC 5322 binding . 9
Annex A (informative): Change History . 10
History . 11


ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 319 522-4-1 V1.2.1 (2019-01)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Electronic Signatures and
Infrastructures (ESI).
The present document is part 4, sub-part 1 of a multi-part deliverable. Full details of the entire series can be found in
part 1 [i.3].

National transposition dates
Date of adoption of this EN: 24 January 2019
Date of latest announcement of this EN (doa): 30 April 2019
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2019
Date of withdrawal of any conflicting National Standard (dow): 31 October 2019

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 319 522-4-1 V1.2.1 (2019-01)
1 Scope
The present document defines the binding of the ERD messages, whose semantics is defined in ETSI EN 319 522-2 [1]
and whose format is defined in ETSI EN 319 522-3 [2], to the specific transmission protocol AS4 [4].
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 319 522-2: "Electronic Signatures and Infrastructures (ESI); Electronic Registered
Delivery Services; Part 2: Semantic Contents".
[2] ETSI EN 319 522-3: "Electronic Signatures and Infrastructures (ESI); Electronic Registered
Delivery Services; Part 3: Formats".
[3] ETSI TS 119 312: "Electronic Signatures and Infrastructures (ESI); Cryptographic Suites".
[4] OASIS Standard: "AS4 Profile of ebMS 3.0 Version 1.0", January 2013.
[5] W3C Recommendation: "XML Encryption Syntax and Processing Version 1.1", 11 April 2013.
[6] ETSI EN 319 522-4-2: "Electronic Signatures and Infrastructures (ESI); Electronic Registered
Delivery Services; Part 4: Bindings; Sub-part 2: Evidence and identification bindings".
[7] ETSI EN 319 532-3: "Electronic Signatures and Infrastructures (ESI); Registered Electronic Mail
(REM) Services; Part 3: Formats".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] IETF RFC 5322: "Internet Message Format".
[i.2] OASIS Standard: "Web Services Security X.509 Certificate Token Profile 1.1. OASIS Standard
incorporating Approved Errata", 1 November 2006.
[i.3] ETSI EN 319 522-1: "Electronic Signatures and Infrastructures (ESI); Electronic Registered
Delivery Services; Part 1: Framework and Architecture".
ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 319 522-4-1 V1.2.1 (2019-01)
[i.4] OASIS: "ebXML Messaging Services Version 3.0: Part 1, Core Features", Committee
Specification, July 2007.
3 Definition of terms and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI EN 319 522-1 [i.3] apply.
3.2 Abbreviations
For the purposes of the present document, the abbreviations given in ETSI EN 319 522-1 [i.3] apply.
4 Message delivery bindings - general concepts
The present document specifies the bindings of the interface ERDS
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27