|
TECHNICAL SPECIFICATION
Core Network and Interoperability Testing (INT);
Diameter Conformance testing for the Sh/Dh interfaces;
TM
(3GPP Release 13);
Part 1: Protocol Implementation
Conformance Statement (PICS)
---------------------- Page: 1 ----------------------
2 ETSI TS 103 571-1 V1.1.1 (2019-04)
Reference
DTS/INT-00138-1
Keywords
conformance, diameter, PICS, protocol
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI TS 103 571-1 V1.1.1 (2019-04)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
Introduction . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definition of terms, symbols and abbreviations . 6
3.1 Terms . 6
3.2 Symbols . 6
3.3 Abbreviations . 6
4 Conformance . 6
Annex A (normative): PICS pro forma . 7
A.1 The right to copy . 7
A.2 Guidance for completing the ICS pro forma . 7
A.2.1 Purposes and structure . 7
A.2.2 Abbreviations and conventions . 7
A.2.3 Instructions for completing the PICS pro forma. 8
A.3 Identification of the Network Equipment . 9
A.3.1 Introduction . 9
A.3.2 Date of the statement . 9
A.3.3 Network Equipment Under Test identification. 9
A.3.4 Product supplier . 9
A.3.5 Client . 10
A.3.6 PICS contact person . 10
A.4 Identification of the protocol . 11
A.5 Global statement of conformance . 11
A.6 PICS pro forma tables for the Sh and Dh interfaces . 11
A.6.1 Roles . 11
A.6.2 PICS Items for AS and OSA SCS . 11
A.6.2.1 System Capabilities for AS and OSA SCS . 11
A.6.3 PICS Items for HSS and SLF . 12
A.6.3.1 System Capabilities for HSS and SLF . 12
History . 13
ETSI
---------------------- Page: 3 ----------------------
4 ETSI TS 103 571-1 V1.1.1 (2019-04)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Core Network and Interoperability
Testing (INT).
The present document is part 1 of a multi-part deliverable covering the test specifications for the Diameter protocol on
the Sh/Dh interface, as identified below:
Part 1: "Protocol Implementation Conformance Statement (PICS)";
Part 2: "Test Suite Structure (TSS) and Test Purposes (TP)";
Part 3: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT)
pro forma specification".
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
To evaluate protocol conformance of a particular implementation, it is necessary to have a statement of which
capabilities and options have been implemented for a telecommunication specification. Such a statement is called a
Protocol Implementation Conformance Statement (PICS).
ETSI
---------------------- Page: 4 ----------------------
5 ETSI TS 103 571-1 V1.1.1 (2019-04)
1 Scope
The present document provides the Protocol Implementation Conformance Statement (PICS) pro forma for the test
specifications for the Diameter protocol on the Sh/Dh interfaces as specified in ETSI TS 129 328 [1] and ETSI
TS 129 329 [2] in compliance with the relevant requirements and in accordance with the relevant guidance given in
ISO/IEC 9646-7 [4] and ETSI ETS 300 406 [5].
The supplier of a protocol implementation which is claimed to conform to ETSI TS 129 328 [1] and ETSI
TS 129 329 [2] is required to complete a copy of the PICS pro forma provided in annex A of the present document and
is required to provide the information necessary to identify both the supplier and the implementation.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI TS 129 328 (V13.10.0): "Digital cellular telecommunications system (Phase 2+) (GSM);
Universal Mobile Telecommunications System (UMTS); LTE; IP Multimedia (IM) Subsystem Sh
interface; Signalling flows and message contents (3GPP TS 29.328 version 13.10.0 Release 13)".
[2] ETSI TS 129 329 (V13.1.0): "Digital cellular telecommunications system (Phase 2+) (GSM);
Universal Mobile Telecommunications System (UMTS); LTE; Sh interface based on the Diameter
protocol; Protocol details (3GPP TS 29.329 version 13.1.0 Release 13)".
[3] ISO/IEC 9646-1: "Information technology - Open Systems Interconnection - Conformance testing
methodology and framework - Part 1: General concepts".
[4] ISO/IEC 9646-7: "Information technology - Open Systems Interconnection - Conformance testing
methodology and framework - Part 7: Implementation Conformance Statements".
[5] ETSI ETS 300 406: "Methods for testing and Specification (MTS); Protocol and profile
conformance testing specifications; Standardization methodology".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TR 121 905 (V10.3.0): "Digital cellular telecommunications system (Phase 2+); Universal
Mobile Telecommunications System (UMTS); LTE; Vocabulary for 3GPP Specifications (3GPP
TR 21.905 version 10.3.0 Release 10)".
ETSI
---------------------- Page: 5 ----------------------
6 ETSI TS 103 571-1 V1.1.1 (2019-04)
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in ETSI TS 129 328 [1], ETSI TS 129 329 [2] and the
following apply:
PICS pro forma: document, in the form of a questionnaire, designed by the protocol specifier or conformance test suite
specifier, which, when completed for an OSI implementation or system, becomes the PICS
NOTE: See ISO/IEC 9646-1 [3].
Protocol Implementation Conformance Statement (PICS): statement made by the supplier of an Open Systems
Interconnection (OSI) implementation or system, stating which capabilities have been implemented for a given OSI
protocol
NOTE: See ISO/IEC 9646-1 [3].
static conformance review: review of the extent to which the static conformance requirements are met by the IUT,
accomplished by comparing the PICS with the static conformance requirements expressed in the relevant standard(s)
NOTE: See ISO/IEC 9646-1 [3].
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in ETSI TS 129 328 [1], ETSI TS 129 329 [2] and
ETSI TR 121 905 [i.1] apply.
4 Conformance
A PICS pro forma which conforms to this PICS pro forma specification shall be technically equivalent to annex A, and
shall preserve the numbering and ordering of the items in annex A.
A PICS which conforms to this PICS pro forma specification shall:
a) describe an implementation which claims to conform to ETSI TS 129 328 [1] and ETSI TS 129 329 [2];
b) be a conforming ICS pro forma which has been completed in accordance with the instructions for completion
given in clause A.1;
c) include the information necessary to uniquely identify both the supplier and the im
...