|
TECHNICAL SPECIFICATION
5G;
NR;
User Equipment (UE) conformance specification;
Applicability of radio transmission, radio reception and radio
resource management test cases
(3GPP TS 38.522 version 15.2.0 Release 15)
---------------------- Page: 1 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 1 ETSI TS 138 522 V15.2.0 (2019-05)
Reference
RTS/TSGR-0538522vf20
Keywords
5G
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 2 ETSI TS 138 522 V15.2.0 (2019-05)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 3 ETSI TS 138 522 V15.2.0 (2019-05)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 4
1 Scope . 5
2 References . 5
3 Definitions, symbols and abbreviations . 6
3.1 Definitions . 6
3.2 Symbols . 6
3.3 Abbreviations . 6
4 Recommended test case applicability . 7
4.1 RF conformance test cases . 9
4.1.1 FR1 standalone conformance test cases . 10
4.1.2 FR2 standalone conformance test cases . 16
4.1.3 NR interworking between NR FR1 and NR FR2 and between NR and LTE conformance test cases. 18
4.1.4 Performance conformance test cases . 27
4.2 RRM conformance test cases . 28
Annex A (informative): FFS . 35
Annex B (informative): Change history . 36
History . 37
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 4 ETSI TS 138 522 V15.2.0 (2019-05)
Foreword
This Technical Specification has been produced by the 3rd Generation Partnership Project (3GPP).
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z the third digit is incremented when editorial only changes have been incorporated in the document.
The present document is one part of a multi-part Technical Specification (TS) covering the New Radio (NR) User
Equipment (UE) conformance specification, which is divided in the following parts:
3GPP TS 38.521-1 [1]: NR; User Equipment (UE) conformance specification; Radio transmission and reception;
Part 1: Range 1 Standalone;
3GPP TS 38.521-2 [2]: NR; User Equipment (UE) conformance specification; Radio transmission and reception;
Part 2: Range 2 Standalone;
3GPP TS 38.521-3 [3]: NR; User Equipment (UE) conformance specification; Radio transmission and reception;
Part 3: Range 1 and Range 2 Interworking operation with other radios;
3GPP TS 38.521-4 [4]: NR; User Equipment conformance specification; Radio transmission and reception; Part
4: Performance;
3GPP TS 38.522: NR; User Equipment (UE) conformance specification; Applicability of RF and RRM
test cases;
3GPP TS 38.533 [5]: NR; User Equipment (UE) conformance specification; Radio resource management;
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 5 ETSI TS 138 522 V15.2.0 (2019-05)
1 Scope
The present document provides the Implementation Conformance Statement (ICS) proforma for 5G New Radio (NR)
User Equipment (UE), in compliance with the relevant requirements.
The present document specifies the recommended applicability statement for the test cases included in 3GPP TS
38.521-1 [1], TS 38.521-2 [2], TS 38.521-3 [3], TS 38.521-4 [4] and TS 38.533 [5]. These applicability statements are
based on the features implemented in the UE.
Special conformance testing functions can be found in 3GPP TS 38.509 [6] and the common test environments are
included in 3GPP TS 38.508-1 [7]. Common implementation conformance statement (ICS) proforma can be found in
3GPP TS 38.508-2 [8].
The present document is valid for UE implemented according to 3GPP releases starting from Release 15 up to the
Release indicated on the cover page of the present document.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
- References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
- For a specific reference, subsequent revisions do not apply.
- For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including
a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same
Release as the present document unless the context in which the reference is made suggests a different Release is
relevant (information on the applicable release in a particular context can be found in e.g. test case title,
description or applicability, message description or content).
[1] 3GPP TS 38.521-1: NR; User Equipment (UE) conformance specification; Radio transmission and
reception; Part 1: Range 1 Standalone
[2] 3GPP TS 38.521-2: NR; User Equipment (UE) conformance specification; Radio transmission and
reception; Part 2: Range 2 Standalone
[3] 3GPP TS 38.521-3: NR; User Equipment (UE) conformance specification; Radio transmission and
reception; Part 3: Range 1 and Range 2 Interworking operation with other radios
[4] 3GPP TS 38.521-4: NR; User Equipment conformance specification; Radio transmission and
reception; Part 4: Performance
[5] 3GPP TS 38.533: NR; User Equipment (UE) conformance specification; Radio resource
management
[6] 3GPP TS 38.509: 5GS; Special conformance testing functions for User Equipment (UE)
[7] 3GPP TS 38.508-1: 5GS; User Equipment (UE) conformance specification; Part 1: Common test
environment
[8] 3GPP TS 38.508-2: 5GS; User Equipment (UE) conformance specification; Part 2: Common
Implementation Conformance Statement (ICS) proforma
[9] 3GPP TR 21.905: Vocabulary for 3GPP Specifications
Editor’s note: More specifications need to be added.
ETSI
---------------------- Page: 6 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 6 ETSI TS 138 522 V15.2.0 (2019-05)
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in TR 21.905 [9] and the following apply. A
term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905 [9].
EIRP(Link=Link angle, Meas=Link angle): measurement of the UE such that the link angle is aligned with the
measurement angle. EIRP (indicator to be measured) can be replaced by EIS, Frequency, EVM, carrier Leakage, In-
band eission and OBW. Beam peak search grids, TX beam peak direction, and RX beam peak direction can be selected
to describe Link.
EIRP(Link=Link angle, Meas=beam peak direction): measurement of the EIRP of the UE such that the
measurement angle is aligned with the beam peak direction within an acceptable measurement error uncertainty.
Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system
claimed to conform to a given specification, stating which capabilities have been implemented
ICS proforma: document, in the form of a questionnaire, which when completed for an implementation or system
becomes an ICS
Implementation extra Information for Testing (IXIT): A statement made by a supplier or implementer of an UEUT
which contains or references all of the information (in addition to that given in the ICS) related to the UEUT and its
testing environment, which will enable the test laboratory to run an appropriate test suite against the UEUT
Inter-band carrier aggregation: Carrier aggregation of component carriers in different operating bands.
NOTE: Carriers aggregated in each band can be contiguous or non-contiguous.
Intra-band contiguous carrier aggregation: Contiguous carriers aggregated in the same operating band.
Intra-band non-contiguous carrier aggregation: Non-contiguous carriers aggregated in the same operating band.
IXIT proforma: A document, in the form of a questionnaire, which when completed for an UEUT becomes an IXIT
Protocol Implementation Conformance Statement (PICS): An ICS for an implementation or system claimed to
conform to a given protocol specification
Protocol Implementation eXtra Information for Testing (PIXIT): An IXIT related to testing for conformance to a
given protocol specification
Static conformance review: A review of the extent to which the static conformance requirements are claimed to be
supported by the UEUT, by comparing the answers in the ICS(s) with the static conformance requirements expressed in
the relevant specification(s)
TRP(Link=Link angle): measurement of the TRP of the UE such that the measurement angle is aligned with the beam
peak direction within an acceptable measurement uncertainty. TX beam peak direction and RX beam peak direction can
be selected to describe Link.
NOTE: For requirements based on EIRP/EIS, the radiated interface boundary is associated to the far-field region
3.2 Symbols
For the purposes of the present document, the following symbols apply:
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in TR 21.905 [9] and the following apply. An
abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in
TR 21.905 [9].
For the purposes of the present document, the following abbreviations apply:
ETSI
---------------------- Page: 7 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 7 ETSI TS 138 522 V15.2.0 (2019-05)
CA Carrier Aggregation
EN-DC E-UTRA NR-Dual Connection
FR1 Frequency Range 1 (450 MHz - 6000 MHz)
FR2 Frequency Range 2 (24250 MHz - 52600 MHz)
ICS Implementation Conformance Statement
IXIT Implementation eXtra Information for Testing
NR New Radio
PIXIT Protocol Implementation eXtra Information for Testing
SCS System Conformance Statement
SUL Supplementary UpLink
TC Test Case
TRP Total Radiated Power
UEUT User Equipment Under Test
4 Recommended test case applicability
The applicability of each individual test is identified in the tables 4.1.1-1 / 4.1.2-1 / 4.1.3-1 / 4.1.4-1 / 4.2-1. This is just
a recommendation based on the purpose for which the test case was written.
The test case applicability condition of every test is formally expressed by the use of Boolean expression that are based
on parameters (ICS) included in annex A of TS 38.508-2 [8] without reference.
Selection criteria of tested bands and tested CA configurations for each applicable test is formally expressed using
group theory based on parameters (ICS) included in annex A of TS 38.508-2 [8] without reference.
Additional information related to the Test Case (TC), e.g. affecting its dynamic behaviour or its execution may be
provided as well.
The columns in tables 4.1.1-1 / 4.1.2-1 / 4.1.3-1 / 4.1.4-1 / 4.2-1 have the following meaning:
Clause
The clause column indicates the clause number in TS 38.521-1 [1], TS 38.521-2 [2], TS 38.521-3 [3], TS 38.521-4 [4]
and TS 38.533 [5] that contains the test body.
Title
The title column describes the name of the test and contains the clause title of the clause in TS 38.521-1 [1], TS 38.521-
2 [2], TS 38.521-3 [3], TS 38.521-4 [4] and TS 38.533 [5] that contains the test body.
Release
The release column indicates the earliest release from which each test case is applicable. It may also indicate a range of
releases or a single release to which a test case is applicable.
Applicability - Condition
The following notations are used for the applicability column:
R recommended - the test case is recommended to all terminals supporting NR
O optional - the test case is optional
N/A not applicable - in the given context, the test case is not recommended.
Ci conditional - the test is recommended ("R") or not ("N/A") depending on the support of other
items. "i" is an integer identifying a unique conditional status expression which is defined
immediately following the table. For nested conditional expressions, the syntax "IF . THEN (IF .
THEN . ELSE.) ELSE ." is used to avoid ambiguities.
Applicability - Comments
This comments column contains a verbal description of the condition included in the applicability column.
ETSI
---------------------- Page: 8 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 8 ETSI TS 138 522 V15.2.0 (2019-05)
Tested Bands / CA-Configurations Selection
This column defines a set of bands / CA Configurations the test is to be run for, if the test is applicable. If the set is
empty, the test is considered as not applicable.
The following notations are used in the tested bands selection column:
Di Derive the set based on Band Selection Criteria Di defined in table [FFS].
Eli Derive the set based on CA Configurations Selection Criteria Ei defined in table [FFS].
TBD Band selection not defined at this time, in the meantime test all Bands / CA Configurations
Text For more complex selection criteria, or if the criteria are already specified somewhere else in the
spec, text reference to the section is given.
Additional Information
This column contains indication if the test case may perform differently depending on the UE capabilities.
NOTE 1: To meet the validation requirements from certification bodies then there is a need to uniquely reference
the FDD and TDD branch (i.e. different behaviour within one and the same TC) of common FDD and
TDD RF test cases in table 4.1-1. The FDD and TDD branches of common FDD and TDD test cases can
be referenced by amending a "FDD" or "TDD" suffix to the test case clause number.
NOTE 2: To meet the validation requirements from certification bodies then there is a need to uniquely reference
the 2Rx (UE supports 2 Rx antenna ports in the tested band) and 4Rx (UE supports 4 Rx antenna ports in
the tested band) branch of common 2Rx and 4Rx RRM test cases in table 4.2-1. The 2Rx and 4Rx
branches of common 2Rx and 4Rx test cases can be referenced by amending a "2Rx" or "4Rx" suffix to
the test case clause number. For example for test case 4.2.1 the 2Rx and 4Rx branches can be identified
by "4.2.1_2Rx" and "4.2.1_4Rx".
Editor’s note: The above description will be updated when necessary, for example 1Tx and 2Tx differentiation.
ETSI
---------------------- Page: 9 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 9 ETSI TS 138 522 V15.2.0 (2019-05)
4.1 RF conformance test cases
NOTE: To determine applicability of a test case, FGI support in combined or fdd-Add-UE-NR-Capabilities or
tdd-Add-UE- NR-Capabilities, as well as supported CBW and SCS in the RF-Parameters IE (see TS
38.331) which conveys RF related capabilities for NR operation, is taken into account.
ETSI
---------------------- Page: 10 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 10 ETSI TS 138 522 V15.2.0 (2019-05)
4.1.1 FR1 standalone conformance test cases
Table 4.1.1-1: Applicability of RF conformance test cases, ref. TS 38.521-1 [1]
ETSI
---------------------- Page: 11 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 11 ETSI TS 138 522 V15.2.0 (2019-05)
Tested Bands/ Additional
Clause Title Release Applicability
CA- Information
Configurations
Condition Comments
Selection
Transmitter Characteristics
PC3
UE maximum output UEs supporting
6.2.1 Rel-15 FR1_C01 FR1_D01 requirements
power 5GS FR1 PC3
applied
PC2
UEs supporting
FR1_D02 requirements
5GS FR1 PC2
applied
PC3
requirements
applied
Test
Maximum Power UEs supporting
6.2.2 Rel-15 FR1_C01 FR1_D01 execution not
Reduction (MPR) 5GS FR1 PC3
necessary if
TS 38.521-1
6.5.2.4.1 is
executed.
PC2
requirements
applied
Test
UEs supporting
FR1_D02 execution not
5GS FR1 PC2
necessary if
TS 38.521-1
6.5.2.4.1 is
executed.
Configured UEs supporting
6.2.4 Rel-15 FR1_C01 FR1_D01
transmitted power 5GS FR1
Configured
UEs supporting
6.2C.1 transmitted power Rel-15 FR1_C02 FR1_D03
5GS FR1 and SUL
for SUL
UEs supporting
UE maximum output
6.2D.1 Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
power for UL-MIMO
MIMO
UE maximum output UEs supporting
6.2D.2 power reduction for Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
UL-MIMO MIMO
Configured UEs supporting
6.2D.4 transmitted power Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
for UL-MIMO MIMO
Minimum output UEs supporting
6.3.1 Rel-15 FR1_C01 FR1_D01
power 5GS FR1
Test
execution not
UEs supporting necessary if
6.3.2 Transmit OFF power Rel-15 FR1_C01 FR1_D01
5GS FR1 TS 38.521-1
6.3.3.2 is
executed.
General ON/OFF UEs supporting
6.3.3.2 Rel-15 FR1_C01 FR1_D01
time mask 5GS FR1
UEs supporting
6.3.3.4 PRACH time mask Rel-15 FR1_C01 FR1_D01
5GS FR1
UEs supporting
6.3.3.6 SRS time mask Rel-15 FR1_C01 FR1_D01
5GS FR1
PUSCH-PUCCH
UEs supporting
6.3.3.7 and PUSCH-SRS Rel-15 FR1_C01
FR1_D01
5GS FR1
time masks
Absolute power UEs supporting
6.3.4.2 Rel-15 FR1_C01 FR1_D01
tolerance 5GS FR1
Power Control
UEs supporting
6.3.4.3 Relative power Rel-15 FR1_C01 FR1_D01
5GS FR1
tolerance
Aggregate power UEs supporting
6.3.4.4 Rel-15 FR1_C01 FR1_D01
tolerance 5GS FR1
ETSI
---------------------- Page: 12 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 12 ETSI TS 138 522 V15.2.0 (2019-05)
Tested Bands/ Additional
Clause Title Release Applicability
CA- Information
Configurations
Condition Comments
Selection
UEs supporting
Minimum output
6.3D.1 Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
power for UL-MIMO
MIMO
UEs supporting
Transmit OFF power
6.3D.2 Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
for UL-MIMO
MIMO
Transmit ON/OFF UEs supporting
6.3D.3 time mask for UL- Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
MIMO MIMO
Absolute power UEs supporting
6.3D.4.1 tolerance for UL- Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
MIMO MIMO
Relative power UEs supporting
6.3D.4.2 tolerance for UL- Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
MIMO MIMO
Aggregate power UEs supporting
6.3D.4.3 tolerance for UL- Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
MIMO MIMO
UEs supporting
6.4.1 Frequency error Rel-15 FR1_C01 FR1_D01
5GS FR1
Error Vector UEs supporting
6.4.2.1 Rel-15 FR1_C01 FR1_D01
Magnitude 5GS FR1
UEs supporting
6.4.2.2 Carrier leakage Rel-15 FR1_C01 FR1_D01
5GS FR1
UEs supporting
6.4.2.3 In-band emissions Rel-15 FR1_C01 FR1_D01
5GS FR1
EVM equalizer UEs supporting
6.4.2.4 Rel-15 FR1_C01 FR1_D01
spectrum flatness 5GS FR1
EVM equalizer
UEs supporting
6.4.2.5 spectrum flatness Rel-15 FR1_C01 FR1_D01
5GS FR1
for Pi/2 BPSK
UEs supporting
Frequency error for
6.4A.1.1 Rel-15 FFS 5GS FR1 and CA FFS
CA (2UL CA)
(2UL CA)
Error Vector UEs supporting
6.4A.2.1.1 Magnitude for CA Rel-15 FFS 5GS FR1 and CA FFS
(2UL CA) (2UL CA)
UEs supporting
Carrier leakage for
6.4A.2.2.1 Rel-15 FFS 5GS FR1 and CA FFS
CA (2UL CA)
(2UL CA)
UEs supporting
In-band emissions
6.4A.2.3.1 Rel-15 FFS 5GS FR1 and CA FFS
for CA (2UL CA)
(2UL CA)
UEs supporting
6.5.1 Occupied bandwidth Rel-15 FR1_C01 FR1_D01
5GS FR1
Transmit UEs supporting
6.5.4 Rel-15 FR1_C01 FR1_D01
intermodulation 5GS FR1
PC3
Spectrum Emission UEs supporting
6.5.2.2 Rel-15 FR1_C01 FR1_D01 requirements
Mask 5GS FR1 PC3
applied
PC2
UEs supporting
FR1_D02 requirements
5GS FR1 PC2
applied
PC3
Additional spectrum UEs supporting
6.5.2.3 Rel-15 FR1_C01 FR1_D01 requirements
emission mask 5GS FR1 PC3
applied
PC2
UEs supporting
FR1_D02 requirements
5GS FR1 PC2
applied
PC3
UEs supporting
6.5.2.4.1 NR ACLR Rel-15 FR1_C01 FR1_D01 requirements
5GS FR1 PC3
applied
ETSI
---------------------- Page: 13 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 13 ETSI TS 138 522 V15.2.0 (2019-05)
Tested Bands/ Additional
Clause Title Release Applicability
CA- Information
Configurations
Condition Comments
Selection
PC2
UEs supporting
FR1_D02 requirements
5GS FR1 PC2
applied
PC3
UEs supporting
6.5.2.4.2 UTRA ACLR Rel-15 FR1_C01 FR1_D01 requirements
5GS FR1 PC3
applied
General spurious UEs supporting
6.5.3.1
Rel-15 FR1_C01 FR1_D01
emissions 5GS FR1
Spurious emission UEs supporting
6.5.3.2 Rel-15 FR1_C01 FR1_D01
for UE co-existence 5GS FR1
Additional spurious UEs supporting
6.5.3.3 Rel-15 FR1_C01 FR1_D01
emissions 5GS FR1
Transmit UEs supporting
6.5.4 Rel-15 FR1_C01 FR1_D01
intermodulation 5GS FR1
Spectrum emission UEs supporting
6.5A.2.2.1 mask for CA (2UL Rel-15 FFS 5GS FR1 and CA FFS
CA) (2UL CA)
UEs supporting
6.5A.2.4.1. NR ACLR for CA
Rel-15 FFS 5GS FR1 and CA FFS
1 (2UL CA)
(2UL CA)
UEs supporting
6.5A.2.4.2. UTRA ACLR for CA
Rel-15 FFS 5GS FR1 and CA FFS
1 (2UL CA)
(2UL CA)
General spurious UEs supporting
6.5A.3.1.1 emissions for CA Rel-15 FFS 5GS FR1 and CA FFS
(2UL CA) (2UL CA)
Spurious emissions UEs supporting
6.5A.3.2.1 for UE co-existence Rel-15 FFS 5GS FR1 and CA FFS
for CA (2UL CA) (2UL CA)
Transmit UEs supporting
6.5A.4.1 intermodulation for Rel-15 FFS 5GS FR1 and CA FFS
CA (2UL CA) (2UL CA)
Occupied bandwidth UEs supporting
6.5C.1 Rel-15 FR1_C02 FR1_D03
for SUL 5GS FR1 and SUL
Spectrum Emission UEs supporting
6.5C.2.2 Rel-15 FR1_C02 FR1_D03
Mask for SUL 5GS FR1 and SUL
Additional spectrum
UEs supporting
6.5C.2.3 emission mask for Rel-15 FR1_C02 FR1_D03
5GS FR1 and SUL
SUL
UEs supporting
6.5C.2.4.1 NR ACLR for SUL Rel-15 FR1_C02
FR1_D03
5GS FR1 and SUL
UTRA ACLR for UEs supporting
6.5C.2.4.2 Rel-15 FR1_C02 FR1_D03
SUL 5GS FR1 and SUL
General spurious UEs supporting
6.5C.3.1 Rel-15 FR1_C02 FR1_D03
emissions for SUL 5GS FR1 and SUL
Spurious emission
UEs supporting
6.5C.3.2 for UE co-existence Rel-15 FR1_C02 FR1_D03
5GS FR1 and SUL
for SUL
Additional spurious UEs supporting
6.5C.3.3 Rel-15 FR1_C02 FR1_D03
emissions for SUL 5GS FR1 and SUL
Transmit
UEs supporting
6.5C.4 intermodulation for Rel-15 FR1_C02 FR1_D03
5GS FR1 and SUL
SUL
UEs supporting
Occupied bandwidth
6.5D.1
Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
for UL-MIMO
MIMO
UEs supporting
Spectrum Emission
6.5D.2.2 Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
Mask for UL-MIMO
MIMO
UEs supporting
NR ACLR for UL-
6.5D.2.4.1 Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
MIMO
MIMO
ETSI
---------------------- Page: 14 ----------------------
3GPP TS 38.522 version 15.2.0 Release 15 14 ETSI TS 138 522 V15.2.0 (2019-05)
Tested Bands/ Additional
Clause Title Release Applicability
CA- Information
Configurations
Condition Comments
Selection
UEs supporting
UTRA ACLR for UL-
6.5D.2.4.2 Rel-15 FR1_C03 5GS FR1 and UL- FR1_D01
MIMO
MIMO
General spurious UEs supporting
6.5D.3.1 emissions for UL- Rel-15 FR1_C03 5GS FR1 and UL
...