|
TECHNICAL SPECIFICATION
Digital cellular telecommunications system (Phase 2+) (GSM);
GSM/EDGE Radio transmission and reception
(3GPP TS 45.005 version 14.6.0 Release 14)
R
GLOBAL SYSTEM FOR
MOBILE COMMUNICATIONS
---------------------- Page: 1 ----------------------
3GPP TS 45.005 version 14.6.0 Release 14 1 ETSI TS 145 005 V14.6.0 (2019-05)
Reference
RTS/TSGR-0645005ve60
Keywords
GSM
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 45.005 version 14.6.0 Release 14 2 ETSI TS 145 005 V14.6.0 (2019-05)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 45.005 version 14.6.0 Release 14 3 ETSI TS 145 005 V14.6.0 (2019-05)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 10
1 Scope . 11
1.1 References . 12
1.2 Abbreviations . 13
1.3 Definitions . 14
2 Frequency bands and channel arrangement . 14
3 Reference configuration . 17
4 Transmitter characteristics . 18
4.1 Output power . 18
4.1.1 Mobile Station . 18
4.1.2 Base station . 23
4.1.2.1 Additional requirements for PCS 1 900 and MXM 1900 Base stations . 25
4.1.2.2 Additional requirements for GSM 850 and MXM 850 Base stations . 25
4.1.2.3 Additional requirements for GSM 700 Base stations . 25
4.1.2.4 Additional requirements for ER-GSM 900 Base stations . 25
4.1.2.4.1 Uncoordinated deployment . 26
4.1.2.4.2 Coordinated deployment . 26
4.2 Output RF spectrum . 26
4.2.1 Spectrum due to the modulation and wide band noise . 26
4.2.1.1 General requirements for all types of Base stations and MS . 26
4.2.1.2 Additional requirements for multicarrier BTS . 27
4.2.1.3 Tables for spectrum requirements due to modulation and wideband noise . 28
4.2.1.4 Exceptions for spectrum due to modulation and wideband noise . 32
4.2.1.4.1 Mobile Stations and Base Transceiver Stations except multicarrier BTS . 32
4.2.1.4.2 Multicarrier BTS . 33
4.2.2 Spectrum due to switching transients . 33
4.2.2.1 General requirements . 33
4.2.2.2 Mobile Station: . 34
b) Base transceiver station: . 34
4.3 Spurious emissions . 35
4.3.1 Principle of the specification . 35
4.3.2 Base Transceiver Station . 37
4.3.2.1 General requirements . 37
4.3.2.2 Additional requirements for co-existence with GSM systems on other frequency bands . 38
4.3.2.3 Additional requirements for co-existence with 3 G . 39
4.3.3 Mobile Station . 40
4.3.3.1 Mobile Station GSM 400, T-GSM 810, GSM 900, ER-GSM 900 and DCS 1 800 . 40
4.3.3.2 Mobile Station GSM 700, GSM 850 and PCS 1 900 . 41
4.4 Radio frequency tolerance . 42
4.5 Output level dynamic operation . 42
4.5.1 Base Transceiver Station . 42
4.5.2 Mobile Station . 42
4.6 Modulation accuracy . 43
4.6.1 GMSK modulation . 43
4.6.2 QPSK, AQPSK, 8-PSK, 16-QAM and 32-QAM modulations . 43
4.6.2.1 RMS EVM . 44
4.6.2.1.1 MS requirements . 44
4.6.2.1.2 Requirements for BTS . 44
4.6.2.2 Origin Offset Suppression . 45
4.6.2.3 Peak EVM . 45
4.6.2.4 95:th percentile . 45
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 45.005 version 14.6.0 Release 14 4 ETSI TS 145 005 V14.6.0 (2019-05)
4.6.3 Phase and amplitude coherency when using blind physical layer transmissions . 46
4.6.3.1 General . 46
4.6.3.2 EC-GSM-IoT MS . 46
4.6.3.3 BTS supporting EC-GSM-IoT . 46
4.7 Intermodulation attenuation. 46
4.7.1 Base transceiver station . 46
4.7.2 Intra BTS intermodulation attenuation . 46
4.7.2.1 GSM 400, GSM 900, ER-GSM 900, DCS 1800 . 47
4.7.2.1.1 Requirements for BTS except multicarrier BTS . 47
4.7.2.1.2 Requirements for multicarrier BTS . 47
4.7.2.2 MXM 850 and MXM 1900 . 47
4.7.2.3 GSM 700, GSM 850 and PCS 1900 . 48
a) Requirements for BTS except multicarrier BTS . 48
b) Requirements for multicarrier BTS . 48
c) Additional requirements for all BTS . 48
4.7.3 Void . 48
4.7.4 Mobile PBX (GSM 900 only) . 48
5 Receiver characteristics . 48
5.1 Blocking characteristics . 49
5.1.1 Definitions of applicable frequency ranges . 49
5.1.2 Requirements for MS . 51
5.1.3 Requirements for BTS . 53
5.1.4 Signal levels of blocking signal . 54
5.1.5 Micro- and pico-BTS . 59
5.2 AM suppression characteristics . 59
5.2.1 Requirements for MS . 59
5.2.2 Requirements for BTS . 60
5.3 Intermodulation characteristics . 61
5.3.1 Requirements for MS . 61
5.3.2 Requirements for BTS . 61
5.4 Spurious emissions . 62
6 Transmitter/receiver performance . 62
6.1a MS conditions . 62
6.1b BTS conditions . 63
6.1 Nominal Error Rates (NER) . 65
6.1.1 GMSK modulation . 65
6.1.1.1 General performance requirements . 65
6.1.1.2 Requirements for MS . 65
6.1.1.3 Requirements for BTS. 65
6.1.2 QPSK/8-PSK modulation . 66
6.1.2.1 Requirements for MS . 66
6.1.2.2 Requirements for BTS. 67
6.1.3 16-QAM/32-QAM modulation . 67
6.1.3.1 Requirements for MS . 67
6.1.3.2 Requirements for BTS. 68
6.2 Reference sensitivity level . 68
6.2.1 Circuit-switched channels . 68
6.2.1a Reference performance in VAMOS mode . 71
6.2.2 Packet-switched channels . 72
6.2.3 Flexible Layer One . 74
6.2.4 Repeated associated control channel performance . 74
6.2.4a Extended Coverage control channel and data channel performance for EC-GSM-IoT . 75
6.2.5 Enhanced MS receiver performance . 75
6.2.6 Additional performance conditions . 75
6.3 Reference interference level . 76
6.3.1 GMSK modulated speech channels and associated control channels . 76
6.3.2 Co-channel reference interference performance . 76
6.3.2.1 MS requirements . 76
6.3.2.2 BTS requirements . 77
6.3.3 Adjacent channel reference interference performance . 77
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 45.005 version 14.6.0 Release 14 5 ETSI TS 145 005 V14.6.0 (2019-05)
6.3.3.1 Normal symbol rate used . 77
6.3.3.1.1 MS requirements . 78
6.3.3.1.2 BTS requirements . 79
6.3.3.2 Higher symbol rate used . 79
6.3.3.2.1 MS requirements . 79
6.3.3.2.2 BTS requirements . 80
6.3.4 Reference interference performance – signal levels . 80
6.3.5 Additional reference interference performance requirements and conditions. 81
6.4 Erroneous frame indication performance . 83
6.5 Random access and paging performance at high input levels . 84
6.6 Frequency hopping performance under interference conditions . 85
6.7 Incremental Redundancy Performance for EGPRS and EGPRS2 MS . 85
Annex A (informative): Spectrum characteristics (spectrum due to the modulation) . 199
Annex B (normative): Transmitted power level versus time . 207
Annex C (normative): Propagation conditions . 213
C.1 Simple wideband propagation model . 213
C.2 Doppler spectrum types . 213
C.3 Propagation models . 214
C.3.1 Typical case for rural area (Rax): (6 tap setting) . 214
C.3.2 Typical case for hilly terrain (HTx): (12 tap setting). 214
C.3.3 Typical case for urban area (Tux): (12 tap setting) . 215
C.3.4 Profile for equalization test (Eqx): (6 tap setting) . 215
C.3.5 Typical case for very small cells (Tix): (2 tap setting) . 215
Annex D (normative): Environmental conditions . 216
D.1 General . 216
D.2 Environmental requirements for the MSs. 216
D.2.1 Temperature (GSM 400, GSM 900, ER-GSM 900 and DCS 1 800) . 216
D.2.1.1 Environmental Conditions (PCS 1 900, GSM 850 and GSM 700) . 216
D.2.2 Voltage . 216
D.2.3 Vibration (GSM 400, GSM 900, ER-GSM 900 and DCS 1 800). 217
D.2.3.1 Vibration (PCS 1 900, GSM 850 and GSM 700). 217
D.3 Environmental requirements for the BSS equipment . 217
D.3.1 Environmental requirements for the BSS equipment . 218
Annex E (normative): Repeater characteristics . 219
E.1 Introduction . 219
E.2 Spurious emissions . 219
E.3 Intermodulation products . 220
E.4 Out of band gain . 220
E.5 Frequency error and modulation accuracy . 220
E.5.1 Frequency error . 220
E.5.2 Modulation accuracy at GMSK modulation . 220
E.5.3 Modulation accuracy at 8-PSK, 16-QAM, 32-QAM, QPSK and AQPSK modulation . 220
Annex F (normative): Antenna Feeder Loss Compensator Characteristics (GSM 400, GSM
900 and DCS 1800) . 222
F.1 Introduction . 222
F.2 Transmitting path . 222
F.2.1 Maximum output power . 222
F.2.2 Gain . 223
ETSI
---------------------- Page: 6 ----------------------
3GPP TS 45.005 version 14.6.0 Release 14 6 ETSI TS 145 005 V14.6.0 (2019-05)
F.2.3 Burst transmission characteristics .
...