|
1:2002/oprA1:2006
PREDSTANDARD
januar 2006
Dvižne ploščadi – Dvižne ploščadi, nameščene na cestna vozila – Varnostne
zahteve – 1. del: Tovorne dvižne ploščadi
(istoveten EN 1756-1:2001/prA1:2005)
Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements -
Part 1: Tail lifts for goods
ICS 53.020.99 Referenčna številka
SIST EN 1756-1:2002/oprA1:2006(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
EN 1756-1:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
November 2005
ICS
English Version
Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety
requirements - Part 1: Tail lifts for goods
Hayons élévateurs - Plates-formes élévatrices à monter sur Hubladebühnen - Plattformlifte für die Anbringung an
véhicules roulants - Prescriptions de sécurité - Partie 1: Radfahrzeugen - Sicherheitsanforderungen - Teil 1:
Hayons élévateurs pour marchandises Hubladebühnen für Güter
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 98.
This draft amendment A1, if approved, will modify the European Standard EN 1756-1:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status
as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1756-1:2001/prA1:2005:2005: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 1756-1:2001/prA1:2005 (E)
Contents Page
Foreword.3
2 Normative references.4
3 Terms and definitions .4
5 Safety requirements and/or protective measures.4
5.2 Working area.4
5.11 Crushing and shearing.4
5.13.1 Surface.4
5.13.2 Bluntness of edges.5
5.16.1 Prevention of lifting excessive loads.5
5.17.5 Several control devices for one movement .5
7 Verification of the safety requirements and/or measures .5
B.1 General.6
B.2.1 Two-hand control.6
B.2.3 Toe guard.
...