|
SIST EN 710:2000/kFprA1:2009
01-november-2009
9DUQRVWVWURMHY9DUQRVWQH]DKWHYH]DOLYDUVNHVWURMHVWURMH]DL]GHODYRMHGHULQ
SULSDGDMRþRRSUHPR
Safety of machinery - Safety requirements for foundry moulding and coremaking
machinery and plant associated equipment
Sicherheit von Maschinen - Sicherheitsanforderungen an Gießereimaschinen und -
anlagen der Form- und Kernherstellung und dazugehörige Einrichtungen
Sécurité des machines - Prescriptions de sécurité applicables aux machines et chantiers
de moulage et de noyautage en fonderie et à leurs équipements annexes
Ta slovenski standard je istoveten z: EN 710:1997/FprA1
ICS:
13.110 Varnost strojev Safety of machinery
25.120.30 Livarska oprema Moulding equipment
SIST EN 710:2000/kFprA1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 710:2000/kFprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 710:2000/kFprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 710:1997
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
September 2009
ICS 25.120.30
English Version
Safety of machinery - Safety requirements for foundry moulding
and coremaking machinery and plant associated equipment
Sécurité des machines - Prescriptions de sécurité Sicherheit von Maschinen - Sicherheitsanforderungen an
applicables aux machines et chantiers de moulage et de Gießereimaschinen und -anlagen der Form- und
noyautage en fonderie et à leurs équipements annexes Kernherstellung und dazugehörige Einrichtungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 202.
This draft amendment A1, if approved, will modify the European Standard EN 710:1997. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 710:1997/FprA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 710:2000/kFprA1:2009
EN 710:1997/FprA1:2009 (E)
Contents Page
Foreword .3
1 Modification of the title .4
2 Modification to "Contents" .4
3 Modification to "Foreword" .4
4 Modification to "Introduction" .4
5 Modification to Clause 2, "Normative references" .4
6 Modification to Clause 3, "Definitions" .6
7 Modifications to Clause 4, "Hazards" . 10
8 Modifications to Clause 5, "Safety requirements and measures" . 10
9 Modifications to 5.2 to 5.8 . 13
10 Modification to Clause 6, "Verification of the safety requirements and preventative
measures according to clause 5" .
...