|
SIST EN 12545:2000/kprA1:2009
01-januar-2009
6WURML]DL]GHODYRþHYOMHYXVQMHQLKL]GHONRYLQL]GHONRYL]XPHWQHJDXVQMD
0HUMHQMHKUXSD6SORãQH]DKWHYH
Footwear, leather and imitation leather goods manufacturing machines - Noise test code
- Common requirements
Maschinen zur Herstellung von Leder- und Kunstlederwaren und Schuhwerk -
Geräuschmessung - Allgemeine Anforderungen
Machines de fabrication de chaussures et d'articles en cuir et en matériaux similaires -
Code d'essai acoustique - Exigences générales
Ta slovenski standard je istoveten z: EN 12545:2000/prA1
ICS:
17.140.20 Emisija hrupa naprav in Noise emitted by machines
opreme and equipment
59.140.40 Stroji in oprema za Machines and equipment for
proizvodnjo usnja in krzna leather and fur production
61.080 âLYDOQLVWURMLLQGUXJDRSUHPD Sewing machines and other
]DREODþLOQRLQGXVWULMR equipment for the clothing
industry
SIST EN 12545:2000/kprA1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12545:2000/kprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 12545:2000/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 12545:2000
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
October 2008
ICS 17.140.20; 59.140.40; 61.060
English Version
Footwear, leather and imitation leather goods manufacturing
machines - Noise test code - Common requirements
Machines de fabrication de chaussures et d'articles en cuir Maschinen zur Herstellung von Leder- und
et en matériaux similaires - Code d'essai acoustique - Kunstlederwaren und Schuhwerk - Geräuschmessung -
Exigences générales Allgemeine Anforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 201.
This draft amendment A1, if approved, will modify the European Standard EN 12545:2000. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12545:2000/prA1:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12545:2000/kprA1:2009
EN 12545:2000/prA1:2008 (E)
Foreword
This document (EN 12545:2000/prA1:2008) has been prepared by Technical Committee CEN/TC 201 “Leather
and imitation leather goods and footwear manufacturing machinery - Safety”, the secretariat of which is held by
UNI.
This document is currently submitted to the Unique Acceptance Procedure.
The first reason for amending the published standard EN 12545:2000 is the revision of the EU-Machinery
Directive 98/37/EC into 2006/42/EC, requiring the adaptation of published European standards cited in the
Official Journal of the European Communities under that Directive.
Additionally at this occasion the normative references have been updated, while also some other limited rather
editorial improvements and corrections have been made.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
2
---------------------- Page: 4 ----------------------
SIST EN 12545:2000/kprA1:2009
EN 12545:2000/prA1:2008 (E)
1 Modification to the Foreword
th
Delete the existing 4 paragraph and replace it with the following: "For relationship with EU Directive(s), see
informative Annexes ZA and ZB, which are integral parts of this document."
2 Modification to the Introduction
Delete the existing text and replace it with the following:
"This document is a type
...