|
SIST EN 848-1:2007/kFprA1:2009
01-junij-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY5H]NDOQLNL]YUWLOQLPRURGMHP]DHQRVWUDQVNR
REGHODYRGHO (QRYUHWHQVNLQDYSLþQLUH]NDOQLVWURML
Safety of woodworking machines - One side moulding machines with rotating tools - Part
1: Single spindle vertical moulding machines
Sicherheit von Holzbearbeitungsmaschinen - Fräsmaschinen für einseitige Bearbeitung
mit drehendem Werkzeug - Teil 1: Einspindelige senkrechte Tischfräsmaschinen
Sécurité des machines pour le travail du bois - Machines à fraiser sur une face à outil
rotatif - Partie 1: Toupies monobroches à arbre vertical
Ta slovenski standard je istoveten z: EN 848-1:2007/FprA1:2009
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 848-1:2007/kFprA1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 848-1:2007/kFprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 848-1:2007/kFprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 848-1:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
April 2009
ICS 79.120.10
English Version
Safety of woodworking machines - One side moulding machines
with rotating tools - Part 1: Single spindle vertical moulding
machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
fraiser sur une face à outil rotatif - Partie 1: Toupies
Fräsmaschinen für einseitige Bearbeitung mit drehendem
monobroches à arbre vertical Werkzeug - Teil 1: Einspindelige senkrechte
Tischfräsmaschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 848-1:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 848-1:2007/FprA1:2009:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 848-1:2007/kFprA1:2009
EN 848-1:2007/FprA1:2009 (E)
Contents Page
Foreword .3
1 Modification to the French title .4
2 Modification to the Foreword .4
3 Modification to Clause 1, Scope .4
4 Modification to Clause 2, Normative references .4
5 Modification to 5.4.5, Ergonomics and handling .4
6 Modification to 6.2, Marking .4
7 Modification to 6.3, Instruction handbook .5
8 Modification to Annex ZA .5
9 Addition of Annex ZB .5
Annex ZB (informative) Relationship between this European Standard and the Essentia
...