|
SIST EN 1218-2:2004/kprA1:2009
01-februar-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY6WURML]DL]GHORYDQMHþHSRYLQXWRURYGHO
'YRVWUDQVNLVWURML]DL]GHORYDQMHþHSRYLQXWRURYR]LURPDSURILOQLVWURML]YHULåQLP
SRGDMDQMHP
Safety of woodworking machines - Tenoning machines - Part 2: Double end tenoning
and/or profiling machines fed by chain or chains
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen -
Teil 2: Doppelseitige Zapfenschneid- und Schlitzmaschinen und/oder Doppelendprofiler
mit Kettenbandvorschub
Sécurité des machines pour le travail du bois - Tenonneuses - Partie 2: Machines à
tenonner et/ou à profiler à chaîne ou chaînes
Ta slovenski standard je istoveten z: EN 1218-2:2004/prA1
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1218-2:2004/kprA1:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1218-2:2004/kprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 1218-2:2004/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 1218-2:2004
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
November 2008
ICS 79.120.10
English Version
Safety of woodworking machines - Tenoning machines - Part 2:
Double end tenoning and/or profiling machines fed by chain or
chains
Sécurité des machines pour le travail du bois - Sicherheit von Holzbearbeitungsmaschinen -
Tenonneuses - Partie 2: Machines à tenonner et/ou à Zapfenschneid- und Schlitzmaschinen - Teil 2:
profiler à chaîne ou chaînes Doppelseitige Zapfenschneid- und Schlitzmaschinen
und/oder Doppelendprofiler mit Kettenbandvorschub
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1218-2:2004. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1218-2:2004/prA1:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1218-2:2004/kprA1:2009
EN 1218-2:2004/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to the Introduction.4
3 Modification to Clause 1, Scope.4
4 Modification to Clause 2, Normative references .4
5 Modification to 3.3, Definitions.5
6 Modification to Clause 4, List of hazards.6
7 Modification to 5.2.1, Safety and reliability of control systems.7
8 Modification to 5.2.3, Starting.8
9 Modification to 5.2.4.1, Normal stopping .8
10 Modification to 5.2.4.2, All other stop controls.
...