|
SLOVENSKI STANDARD
SIST EN 13683:2004/oprA1:2007
01-september-2007
Oprema za nego vrta - Motorni drobilniki/sekalniki - Varnost
Garden equipment - Integrally powered shredders/chippers - Safety
Gartengeräte - Motorgetriebene Schredder/Zerkleinerer - Sicherheit
Matériel de jardinage - Broyeurs/déchiqueteurs a moteur a combustion interne - Sécurité
Ta slovenski standard je istoveten z: EN 13683:2003/prA1
ICS:
65.060.70 Vrtnarska oprema Horticultural equipment
SIST EN 13683:2004/oprA1:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
DRAFT
EN 13683:2003
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
April 2007
ICS 65.060.70
English Version
Garden equipment - Integrally powered shredders/chippers -
Safety
Matériel de jardinage - Broyeurs/déchiqueteurs à moteur à Gartengeräte - Motorgetriebene Schredder/Zerkleinerer -
combustion interne - Sécurité Sicherheit
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 144.
This draft amendment A1, if approved, will modify the European Standard EN 13683:2003. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13683:2003/prA1:2007: E
worldwide for CEN national Members.
EN 13683:2003/prA1:2007 (E)
Contents Page
Foreword.3
1 Modification to 5.2.1.1 .4
2 Modification to 5.2.1.2 .4
3 Modification to Table 2.4
4 Modification to 5.2.1.3 .6
5 Modification to 5.2.2 .6
6 Modification to 5.2.3.1 .6
7 Modification to Annex A.6
8 Modification to D.2.3.8
EN 13683:2003/prA1:2007 (E)
Foreword
This document (EN 13683:2003/prA1:2007) has been prepared by Technical Committee CEN/TC 144
“Tractors and machinery for agriculture and forestry”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
EN 13683:2003/prA1:2007 (E)
1 Modification to 5.2.1.1
Delete both indents and replace with the following:
"
either be constructed to meet the dimensional requirements given in 5.2.1.2, 5.2.1.3 and Table 2, or
if a straight rod of 1 m length and 12 mm diameter will not pass through the opening to contact the cutting
means then the tortuous path test of 5.2.1.4 shall apply."
2 Modification to 5.2.1.2
Delete second paragraph and replace with the following:
"Where a feed safety opening is not a slot, square or round, the overall size of opening is considered
...