|
SLOVENSKI STANDARD
01-julij-2022
Rudarstvo - Sistemi za nadzor kakovosti zraka za ohišje operaterja - Zahteve glede
zmogljivosti in preskusne metode (ISO 23875:2021)
Mining - Air quality control systems for operator enclosures - Performance requirements
and test methods (ISO 23875:2021)
Bergbau - Luftqualitätskontrollsysteme für Bedienerkabinen - Leistungsanforderungen
und Prüfverfahren (ISO 23875:2021)
Exploitation minière - Systèmes de contrôle de la qualité de l'air des enceintes de
l'opérateur - Exigences de performance et méthodes essai (ISO 23875:2021)
Ta slovenski standard je istoveten z: EN ISO 23875:2022
ICS:
13.040.30 Kakovost zraka na delovnem Workplace atmospheres
mestu
73.020 Rudarstvo in kamnolomsko Mining and quarrying
izkopavanje
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 23875
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2022
EUROPÄISCHE NORM
ICS 13.040.30; 73.020
English Version
Mining - Air quality control systems for operator
enclosures - Performance requirements and test methods
(ISO 23875:2021)
Exploitation minière - Systèmes de contrôle de la Bergbau - Luftqualitätskontrollsysteme für
qualité de l'air des enceintes de l'opérateur - Exigences Bedienerkabinen - Leistungsanforderungen und
de performance et méthodes essai (ISO 23875:2021) Prüfverfahren (ISO 23875:2021)
This European Standard was approved by CEN on 20 March 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23875:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 23875:2021 has been prepared by Technical Committee ISO/TC 82 "Mining” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 23875:2022 by
Technical Committee CEN/TC 196 “Mining machinery and equipment - Safety” the secretariat of which
is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2022, and conflicting national standards
shall be withdrawn at the latest by September 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 23875:2021 has been approved by CEN as EN ISO 23875:2022 without any modification.
INTERNATIONAL ISO
STANDARD 23875
First edition
2021-02
Mining — Air quality control
systems for operator enclosures —
Performance requirements and test
methods
Reference number
ISO 23875:2021(E)
©
ISO 2021
ISO 23875:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
ISO 23875:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 Terms related to air quality . 2
3.2 Terms related to the operator enclosure design . 2
3.3 Terms related to measurement . 3
4 Requirements . 4
4.1 Performance requirements . 4
4.2 Engineering design . 4
4.2.1 Operator enclosure . 4
4.2.2 Air quality control system. 5
4.2.3 Filters and filter housings . 6
4.3 Monitoring devices . 7
4.3.1 General. 7
4.3.2 Carbon dioxide operator notification system for retrofit installations . 8
4.3.3 Carbon dioxide operator notification system for machine manufacturers . 8
4.3.4 Additional monitoring capabilities . 9
5 Performance testing. 9
5.1 Requirements . 9
5.1.1 Test set up . 9
5.1.2 Test equipment . 9
5.1.3 Test methods .10
5.2 Test report .12
6 Operation and maintenance instructions .13
Annex A (informative) CO management .15
Annex B (informative) Recommendations for the operational integration of this document .17
Bibliography .21
ISO 23875:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 82, Mining.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
ISO 23875:2021(E)
Introduction
Safety in mining operations is of concern to all involved in owning, developing, managing, and working
in mining environments. Routine mining activities can generate airborne particulates which are
hazardous to human health. Therefore, it is necessary to develop controls which limit the operator’s
exposure to airborne particulates while operating equipment from within the operator enclosure.
With the rise in the number of countries regulating air quality in mining, construction, and industrial
environments, machine manufacturers have become increasingly aware of the need for standard
practices in the design and performance of operator enclosures. This document seeks to address the
fundamental design requirements that w
...